The EMS uses the EMS Calea user role for all LI configuration operations and the admin user for communicating over netconf to the SBC. The EMS creates the SBC Calea user credentials automatically when an SBC registers to the EMS. Distributed SBC instances are registered dynamically in the EMS.

Note

A single Call Data Channel (CDC) configuration is supported per cluster. The S-SBC does not support the creation of a media TCP or UDP.

To configure the S-SBC LI through the CLI, refer to the following pages:

Note

For a D-SBC (S-SBC or M-SBC) cluster, configure the CLI on the OAM node for the cluster.

Prerequisites

To configure the CDC for an S-SBC instance:

Configuring CDC using the EMS Calea User Account

The LI Call Data Channel must be configured on the S-SBC to indicate that it supports interception. For LI, the CDC configuration is performed using the CDC Configuration Manager through the EMS. You can create CDC information only when logged in as the EMS Calea user from the EMS CDC configuration window.

Configure Cluster CDC for S-SBC Nodes

To configure a cluster CDC for S-SBC nodes:

  1. Log into the EMS as an admin user.
  2. Click Network > Cluster Management. The Cluster Management / Manage VNFs window opens listing the SBC clusters created on the EMS.

    EMS Cluster/VNF List

  3. Click the radio button adjacent to the name of the cluster you want to configure. The Details tab for the selected cluster opens by default. 
  4. Click the Configurations tab. 

    Cluster Configurations Tab

  5. Click Edit Configuration. The SBC Configuration Manager opens in a separate window against the cluster's active OAM node.
  6. Launch another EMS session as the Calea user.
  7. Under Monitoring, click Lawful Intercept. The Lawful Intercept window is displayed.
  8. Click Cluster CDC. The Lawful Intercept/Cluster CDC window is displayed.

    Lawful Intercept/Cluster CDC

  9. Select the S-SBC cluster.
  10. Click Launch CDC Configuration Manager. The SBC Configuration Manager window is displayed.

Creating a Call Data Channel for the S-SBC (Default, IMS, and PCSI LI)

Note

The S-SBC supports only one CDC. You will receive an error message if you try to create a CDC when a CDC already exists.

To create a new call data channel:

  1. Perform the Configure Cluster CDC for S-SBC Nodes procedure.
  2. In the SBC Configuration Manager window of the Calea user, navigate to Configuration > Intercept > Call Data Channel. The Call Data Channel window is displayed.

    Call Data Channel for S-SBC

    Note

     You can configure LI using the default Address Context only.

  3. Select default from the Address Context drop-down menu.

  4. Click New Call Data Channel. The Create New Call Data Channel window is displayed.

  5. Configure the Create New Call Data Channel panel for either the default, IMS, or PCSI LI. For descriptions of the parameters in the following tables, refer to Intercept - Call Data Channel.

    • To configure the CDC for the default LI, use the following table.

      Note

      You cannot create or modify mediation servers for an S-SBC with a default LI. Since you cannot create mediation servers, you cannot configure the signaling interception for a default LI.

      For S-SBCs with a default LI, you can configure only the CDC. In the CDC configuration, you provide the IP Address and Port details.

      Call Data Channel Parameters - Default LI

       ParameterConfiguration
      NameEnter the name of the CDC configuration object.
      Intercept Standard

      Select one of the following options: Packetcable or Packetcable Plus Etsi.

      Vendor Id

      Select one of the following options: None, Utimaco, or Verint.

      Pri StateSelect Enabled.
      Sec StateSelect Enabled.
      Pri ModeSelect Active.
      Sec ModeSelect Active.
      Pri IP AddressEnter the primary LI server's IP address where the SBC sends the CDC messages.
      Sec IP AddressEnter the secondary LI server's IP address where the SBC sends the CDC messages.
      Pri PortEnter the primary LI server's UDP port where the SBC sends the CDC messages.
      KA TimerEnter the KA timer.
      RetriesEnter the number of retries before the SBC considers the LI CDC as failed.
      IP Interface Group NameSelect the name of the IP interface group you want to use.
      See the following screen capture for an example configuration.

      Create new Call Data Channel - Default LI

    • To configure the CDC for the IMS LI, use the following table. 

      Call Data Channel Parameters - IMS LI

       ParameterConfiguration
      NameEnter the name of the CDC configuration object.
      Intercept StandardSelect one of the following options: Three Gpp or Etsi.
      Vendor IdSelect one of the following options: None, Verint, Utimaco, or Group Two Thousand.
      IP Interface Group NameSelect the name of the IP interface group you want to use.
      Li Pol Dip For Regd Ood MsgEnable or disable the Li Pol Dip For Regd Ood Msg.
      Dsr Protocol VersionEnter the DSR protocol version.
      See the following screen capture for an example configuration.

      Create new Call Data Channel - IMS LI

    • To configure the CDC for the PCSI LI, use the following table. 

      Note

      You cannot create or modify mediation servers for an S-SBC with a PCSI LI. Since you cannot create mediation servers, you cannot configure the signaling interception for a PCSI LI.


      Call Data Channel Parameters - PCSI LI

       ParameterConfiguration
      NameEnter a name for the CDC configuration object.
      Intercept StandardSelect Packetcable.
      Vendor IdSelect Ss8.
      See the following screen capture for an example configuration.

      Create new Call Data Channel - PCSI LI

  6. Click Save. The object is created successfully.

  7. Click OK.

  8. Click Close at the top-right of the SBC Configuration Manager window.

  9. Click Yes to confirm that you want to close the window.
  10. Return to the EMS session containing the SBC Configuration Manager for the OAM node and click Apply Saved Changes and Close.

  11. When prompted, confirm that you want to save and activate your configuration changes.

Creating Mediation Servers

After you create the CDC, you can create mediation server objects that associate with the CDC. The CDC configuration supports up to eight mediation servers.

Note

You can create and modify the mediation servers only for an S-SBC with an IMS LI.

To Create a Mediation Server Object

Use the following procedure to create a mediation server object.

  1. Perform the Configure Cluster CDC for S-SBC Nodes procedure.
  2. In the SBC Configuration Manager window of the Calea user, select Configuration > Intercept > Call Data Channel > Mediation Server.

    Mediation Server

  3. Select default from the Address Context drop-down menu.

  4. Select the CDC you created for the S-SBC from the Call Data Channel drop-down menu.

  5. Click New Mediation Server. The SBC Configuration Manager displays the Create New Mediation Server panel.

    Create new Mediation Server

  6. In the Msname field, enter a mediation server name.
  7. Click Save.
  8. Click Ok.

    Note

    You can repeat the preceding steps to create a maximum of eight mediation servers for the S-SBC.

  9. Click Close at the top-right of the SBC Configuration Manager window.

  10. Click Yes to confirm that you want to close the window.
  11. Return to the EMS session containing the SBC Configuration Manager for the OAM node and click Apply Saved Changes and Close.

  12. When prompted, confirm that you want to save and activate your configuration changes.

To Configure Signaling Interception

Note

You can configure the signaling interception only for an S-SBC with an IMS LI.

Use the following procedure to configure the signaling interception.

  1. Perform the Configure Cluster CDC for S-SBC Nodes procedure.
  2. In the SBC Configuration Manager window of the Calea user, select Configuration > Intercept > Call Data Channel > Mediation Server.

  3. Click Signaling.

    Signaling

  4. Select default from the Address Context drop-down menu.
  5. Select the CDC you created for the S-SBC from the Call Data Channel drop-down menu.
  6. Select the mediation server you created for the S-SBC from the Mediation Server drop-down menu.

  7. Use the following table to configure the Edit Signaling panel. For descriptions of the parameters in this table, refer to Mediation Server - Signaling.

    Signaling Parameters

    Parameter Configuration
    IP Address V4 or V6

    Enter the IPv4 or IPv6 address of the mediation server for the signaling interception.

    Port NumberEnter the port number of the mediation server for the signaling interception.
    DSCP ValueEnter the DSCP value of the intercepted media packets sent on this port.
    Protocol TypeSelect TCP.
    Mode

    Select Out of Service.

    State

    Select Disabled.

    See the following screen capture for an example configuration.

    Edit Signaling - Out of Service

  8. Click Save.
  9. Click Ok.
  10. Configure the Edit Signaling panel with the following values to enable the mediation server:
    1. Mode: Select In Service.
    2. State: Select Enabled.

    Edit Signaling - In Service

  11. Click Save.
  12. Click Ok.
  13. Click Close at the top-right of the SBC Configuration Manager window.

  14. Click Yes to confirm that you want to close the window.
  15. Return to the EMS session containing the SBC Configuration Manager for the OAM node and click Apply Saved Changes and Close.

  16. When prompted, confirm that you want to save and activate your configuration changes.