CLI Changes in This Release

New CLI in 8.2.0R0

SBX-41671 TTY/TDD Interworking Support for RFC-4103 and/or RFC-4351

The parameter generateRtcpForT140IfNotReceivedFromOtherLeg is added to packetServiceProfile rtcpOptions rtcp. When the parameter is set to enable, the SBC generates RTCP for T140 media streams if RTCP is not received from peer.

For more information, refer to the following pages:

• Packet Service Profile - CLI
• Show Status System
• Show Table System 

Command Syntax

To configure the parameter generateRtcpForT140IfNotReceivedFromOtherLeg, use the following syntax:

set profiles media packetServiceProfile <packetServiceProfile_name: INGRESS>
	rtcpOptions 
		rtcp <disable | enable> 
			generateRtcpForT140IfNotReceivedFromOtherLeg <disable | enable>

Command Parameters

SBX-62459 Support for Public-key-Based Peer Authentication Method for IPSec

The SBC is enhanced to support a Public Key-based peer authentication method for IPSec on SBC. In past releases, the SBC used a Preshared key-based authentication method for Peer authentication during IKE negotiation for establishing IKE and IPSec Security associations. To meet Common Criteria certification requirements, the SBC is now capable of using x.509 digital certificates for Peer authentication. Note: Not currently supported on SBC Cloud and D-SBC platforms.

For more information, refer to IPsec Peer - CLI.

Command Syntax

% set addressContext default ipsec peer <peerName> authType <psk | rsaSig>
% set addressContext default ipsec peer <peerName> localCertificate <sbcCertName>
% set addressContext default ipsec peer <peerName> remoteCertificate <peerCertName>
% set addressContext default ipsec peer <peerName> remoteCaCertificate <caCertName1>

Command Parameters

SBX-67554 LCQ CC/SIP Issue - Multiple Call Transfer - SIP Layer Stops Responding

The SBC is enhanced with the parameter maxNumTransfers under the object global signaling.

For more information, refer to Signaling - Global - CLI and Show Table Global.

Command Syntax

To configure maxNumTransfers, use the following syntax:

% set global signaling maxNumTransfers <10-100>

Command Parameters

Configuration Examples

To configure maxNumTransfers, use the following example:

% set global signaling maxNumTransfers 30

To display the maxNumTransfers, use the following example:

• In the "configure" mode:

  % show global signaling maxNumTransfers
  maxNumTransfers 30

• In the "display" mode (when you exit the "configure" mode):

  > show table global signaling
  maxNumTransfers 30;
  messageManipulation {
      inputAdapterProfile  DD1;
      outputAdapterProfile DD1;
  }
  sipPeerOverloadControl {
      samplingPeriod  2;
      discardPeriod   2;
      stepDownGain    100;
      rejectThreshold 1;
  }
  sipSigControls {
      registrarSupportContactParam enabled;
      maxPduSizeValue              pdusize15kb;
  }
  
  

SBX-68878 CDR for SIPREC Sessions

The SBC is enhanced to support a new parameter "Generate Recording CDR" to the OAM > Accounting > Admin. When the "Generate Recording CDR" parameter is enabled, the SBC generates a Recording-CDR. The selected CDR is placed in the .ACT files along with the other call and Event CDRs. All the file size and CDR count rules of the existing CDRs apply to the Recording CDRs. 

For more information, refer to Packet Service Profile - CLI.

Command Syntax

% set oam accounting admin generateSipRecordingCdr <disabled | enabled>

 Command Parameters

SBX-70465 STIR/SHAKEN: Option to Signal Verification Failures in Backward Provisional Responses

The ATIS specification defines an optional capability to signal verification failures in backward provisional responses. If a terminating carrier B fails verification for an originating carrier A subscribers, but continues to deliver the call to the carrier B called party, carrier A will have no way to know. The terminating carrier can use failed verification to indicate robocalling status to the called party. In this case, carrier A has no way to know that their subscribers' calls are being flagged as robocalls to the terminating party.

The capability described in the ATIS specification solves this issue if carrier A has tools in place to find these indications in the SIP messaging.

Trunk-group-level SIP cause value reporting should include counts for each unique case value transmitted. These statistics already exist for the Reason header transmitted at the end of the call; however, this would additionally count the cause values send in the 18x/200 for STIR/SHAKEN.

New STI Profile flag overWriteReasonCodeIn4xxto6xx added regarding 4xx-6xx handling.

For more information, refer to STI Profile - CLI.

Command Syntax

% set profiles services stiProfile <profile_name> overWriteReasonCodeIn4xxto6xx <disabled | enabled>

Command Parameters

SBX-70938 RTCP for T.140 Pass-through

A parameter, t140RtcpMonitorInterval, is added under mediaRTCPControl to define the RTCP monitoring interval. This enables the SBC to wait for an RTCP packet from peer before starting RTCP towards T.140 endpoint with the following PSP flag enabled.

% set system media mediaRtcpControl t140RtcpMonitorInterval 6
% set profiles media packetServiceProfile DEFAULT rtcpOptions generateRtcpForT140IfNotReceivedFromOtherLeg enable

Command Parameters

SBX-75174 - Generate or Replace SSRC Values for Calls Toward a Kandy Link WebRTC Gateway

The synchronization source (SSRC) identifier uniquely identifies media streams within an RTP session and is included in SDP signaling when establishing or modifying media sessions. The WebRTC specification requires that the SSRC value in an RTP stream match the SSRC sent in the SDP. However some endpoints, such as PSTN gateways, are not capable of generating SSRC values so they are not present in the SDP. Other endpoints change the SSRC during call hold/resume scenarios. The SBC provides two flag parameters to the Packet Service profile to determine whether the SBC generates and updates the SSRC and related attributes.

For more information, refer to Packet Service Profile - CLI.

Command Syntax

The SBC adds the following two flags to the Packet Service profile. 

% set profiles media packetServiceProfile <profile name> flags
      generateAndSignalSSRCAndCname <disabled | enabled>
      allowMidCallSSRCModification <disabled | enabled>

The SBC only allows mid-call modifications to the SSRC if it is generating the SSRC. Therefore, the first parameter, generateAndSignalSSRCAndCname, must be enabled for the second parameter, allowMidCallSSRCModification, to become available.

Command Parameters

SBX-75865 Alarm Generation when SBC Receives RCODE Except for 0

The rcodeErrorMonitorTimer parameter is added to the DNSGroup configuration to support monitoring timer interval which the SBC Core uses to monitor RCODE errors.

 For more information, refer to DNS Group - CLI

Command Syntax

% set addressContext <address_context_name> dnsGroup <dnsgroup> rcodeErrorMonitorTimer <rcode_error_monitor_timer>

Command Parameters

SBX-76436 - Increase CDR Retention with Compression

The SBC is enhanced to allow writing accounting files containing CDRs into a compressed format. The compressed files are retained for a user-specified time period; thereafter, they are automatically deleted after a specified number of days. The compressed files are stored in the evlog directory or another directory that you specify.

 For more information, refer to Event Log - CLI

Command Syntax

% set oam eventLog typeAdmin acct
    compressionSupport <both | none | only>
    compressionDaysToKeep <1 .. 7>
    compressionCleanupDirectory

Command Parameters

SBX-76610 Selection Feature for ARS Recovery Algorithm

The following is the full syntax to create a SIP ARS profile, including the new recoveryAlgForTimeouts and recoveryAlgForNoRetryAfter options and their parameters for selecting the ARS recovery algorithm for each blacklist algorithm.

For more information, refer to SIP ARS Profile - CLI.

Command Syntax

 set profiles services sipArsProfile <Profile Name> recoveryAlgForTimeouts < probe | timer | none >

 set profiles services sipArsProfile <Profile Name> recoveryAlgForNoRetryAfter < probe | timer | none >

% set profiles services sipArsProfile <profile name>
   blkListAlgRetryAfterType sip-503
   blkListAlgTimeoutsDuration <1-3600>
   blkListAlgTimeoutsNumTimeouts <1-3600>
   blkListAlgTimeoutsType sip-invite
   blkListAlgorithms <retryafter | timeouts | noRetryAfer>
   blkListAlgNoRetryAfterNum503 <1-3600>
   blkListAlgNoRetryAfterDuration <1-3600>
   failureResponseCodes <400-699 | all |all4xx | all5xx | all6xx>
   midDialogArsScreenLevel <always | never | onlyIfNotBlackListDueto503>
   recoveryAlgProbeDuration <1-3600>
   recoveryAlgProbeInterval <1-600>
   recoveryAlgProbeMethod sip-options
   recoveryAlgProbeNumResponses <1-32>
   recoveryAlgTimerDuration <1-3600>
   recoveryAlgorithm <probe|timer>
   recoveryAlgForTimeouts <probe|timer|none>
   recoveryAlgForNoRetryAfter <probe|timer|none>

Command Parameters

SBX-85716  Re-initiate Pre-condition Negotiation Towards Ingress

Two new parameters are added to SIP trunk group signaling and are shown in the context of the complete command syntax.

• performPrecondtionRenegotiation: to re-initiate precondition procedure when the 
  Unable to show "metadata-from": No such page "_space_variables"
  changes the ingress side SDP due to 18x/200 OK or UPDATE received from the egress side.
• preferUPDATEOverReINVITE: to use UPDATE instead of Re-INVITE on the ingress to communicate SDP, when the call goes to the confirmed state.

For more information, refer to:

• SIP Trunk Group - Signaling - CLI
• SIP TG - Signaling - Prefer UPDATE Over ReINVITE - CLI
• SIP TG - Signaling - Perform Precondtion Renegotiation - CLI

Command Syntax

% set addressContext default zone <zone_name> sipTrunkGroup <siptrunkgroup_name> signaling preferUPDATEOverReINVITE <enabled | disabled>

% set addressContext default zone <zone_name> sipTrunkGroup <siptrunkgroup_ingress_name> signaling performPrecondtionRenegotiation 
<enabled | disabled>

Command Parameters

SBX-86008 Cloud SBC Avalanche Fault - Detection and Control

Packets that cause a direct SBC fault can lead to a catastrophic failure of an SBC service, which is known as a packet-stimulated fault avalanche. These packets appear for various reasons, such as: the SBC adds a new Session Initiation Protocol (SIP) endpoint, upgrades or replaces a peering endpoint or gateway (GW), changes a configuration on a peer, or introduces a new call scenario. The SBC does not currently check for double faults, which is when the SBC has a failover and then another failover. Double faults cause call loss.

For more information, refer to  CLI Configure Mode.

Command Syntax

Use the following command to set and configure the faultAvalancheControl parameter.

% set system faultAvalancheControl callIdThreshold <0-999> calledPartyThreshold <0-999> callingNCalledPartyThreshold <0-999> callingPartyThreshold <0-999> sourceIpThreshold <0-999> faultRecAgeingTimeOut <15-60>

Use the following command to enable or disable the faultAvalancheControl parameter.

% set system faultAvalancheControl facState <disabled | enabled>

Command Parameters

SBX-86658 Offer-Answer Timer Configuration

In specific call scenarios, the SBC treats the Offer-Answer (OA) as a MODIFY Offer-Answer cycle, but the peer treats it as an INITIAL Offer-Answer cycle. According to RFC 3261, the response from the peer is expected within 300 seconds. The SBC, however, assumes a 20-second response, and therefore any delay in the response from the peer which exceeds of 20 seconds causes call failure.

Currently, the internal Offer-Answer (OA) timer value is fixed and cannot be configured. To overcome this limitation, the SBC is enhanced with a new parameter offerAnswerTimer to configure this OA timer.

For more information, refer to Signaling - Global - CLI

Command Syntax

% set global signaling sipSigControls offerAnswerTimer 
Possible completions:
<Enter offer answer timer value in range of (10..300) in seconds.> (20):

Command Parameters

SBX-86789 SBC Should Create TLS Connection Based on Contact Header

The SBC provides the following new SIP trunk group parameter to specify whether to use the Contact header information instead of the source IP address when routing a call to an access user over TLS transport. 

For more information, refer to SIP Trunk Group - Signaling - CLI

Command Syntax

Command Parameters

SBX-87239 Response Code Change When SBC Fails a DNS Query 

 When the SBC fails a DNS query, it generates a 503 or 500 error response. These error codes are now mapped to a configurable response code. A new enum - DnsRcodeError - has been added to internalCause in sonusSipInternalCauseMapProfile.yang to provide mapping entry in existing InternalSipCauseMapProfile profile.

For more information, refer to Show Table Global. and CPC to SIP Cause Map Profile - CLI.

Command Syntax

% set profiles signaling sipCauseCodeMapping internalSipCauseMapProfile <profile_name> causeMap <CPC cause value> DnsRcodeError

Command Parameters

SBX-88542 Prefix-based TG Selection using SMM

The SBC adds support for using  SIP Message Manipulation (SMM) to enable secondary selection of an ingress trunk group. This processing requires two new SMM operations and SIP Param Based Action profiles.

For more information, refer to SIP Adaptor Profile - CLI.

Command Syntax

The following new operations are supported in SMM sipAdaptorProfiles.

%  set profiles signaling sipAdaptorProfile <profileName> rule <rule index> action <action index> operation 
        storeSipParam
        storeProfileName

The SIP Param Based Action profile is supported.

%   set profiles signaling sipParamBasedActionProfile <profileName> 
          action <none | selectTG>
          entry <0 to 2056>
             trunkGroupName <trunk group name>
             matchType 
               full 
                 param <parameter value>
               none
               range 
                 rangeEnd <end of parameter range>
                 rangeStart <start of parameter range>
               regexp
                 paramRegexp <regular expression>

Command Parameters

The following table describes the new SMM operations.

The following table describes the parameters in the sipParamBasedActionProfile.

SBX-88601 SMM: Support Global Configuration

The SBC adds support for applying SIP message manipulation (SMM) profiles (SIP adaptor profiles) at both the global and address context levels and options that control how to execute profiles when they are specified at more than one level.

For more information, refer to Signaling - Global - CLI.

Command Syntax

Global

The following new options specify the names of SIP adaptor profiles to apply at the global level.

% set global signaling messageManipulation
      inputAdapterProfile <profile name>
      outputAdapterProfile <profile name>

Address Context

The following new options specify the names of SIP adaptor profiles to apply to sessions within a specified address context..

% set addressContext <address context> signaling messageManipulation
      inputAdapterProfile <profile name>
      outputAdapterProfile <profile name>

SIP Trunk Group

The following new options specify whether or not to use fixed order execution when multiple SMM profiles apply to a session. When fixed order execution is enabled, you can also specify which of the four profile types to enable and therefore include in SMM processing.

% set addressContext <address context>  zone <zone> sipTrunkGroup <trunk group name> signaling messageManipulation smmProfileExecution 
      none
      fixedOrder 
         addressContext acState <disable | enable>
         global globalState <disable | enable> 
         iptg iptgState <disable | enable>  
         zone zoneState <disable | enable>     

Command Parameters

Global

Address Context

SIP Trunk Group

SBX-70005 Relay Changes in PAID as per RFC-5876

A new Services profile, sipAdaptiveTransparencyProfile, is added to configure SIP header transparency for P-ASSERTED-IDENTITY.

For more information, refer to SIP Adaptive Transparency Profile - CLI.

Under sipAdaptiveTransparencyProfile, the following parameters are added:

• sipMethod
• sipResponse
• state
• triggerHeader
• action
• trigger

Command Syntax

% set profiles services
	sipAdaptiveTransparencyProfile <profile_name>
		sipMethod <UPDATE | INVITE>
		sipResponse <180 | 183 | 200>
		state <disabled | enabled>
		triggerHeader <P-ASSERTED-ID>
			action new-value
			trigger value-change

Command Parameters

sipMethod

SBX-85818 + SBX-85655 Support for SIP-ISUP

The CLI changes are as follows:

• The following profiles are added under the object profiles signaling:
  • calledPrefixMatchProfile
  • carrierCodeToIoiMappingProfile
  • ioiToCarrierCodeMappingProfile
  • sipJJ9030InterworkingProfile
    For information on the parameters associated with each of the profiles, see the sub-section Command Syntax.
• The following parameter is added under the object profiles signaling NNIProfile:
  • contractorNumInterworking
• The following profiles are added under the object addressContext zone sipTrunkGroup signaling:
  • calledPrefixMatchProfile
  • sipJJ9030InterworkingProfile

For more information, refer to the following pages:

• Called Prefix Match Profile - CLI
• Carrier Code to Ioi Mapping Profile - CLI
• Ioi to Carrier Code Mapping Profile - CLI
• SIP JJ9030Interworking Profile - CLI
• NNI Profile - CLI
• SIP TG - Signaling - Called Prefix Match Profile - CLI (Duplicate of Called Prefix Match Profile - CLI)
• SIP TG - Signaling - SIP JJ9030Interworking Profile - CLI (Duplicate of SIP JJ9030Interworking Profile - CLI)
• Show Table Profiles - Signaling

Command Syntax

To configure the signaling profile calledPrefixMatchProfile, use the following syntax:

% set profiles signaling
	calledPrefixMatchProfile <called_prefix_match_profile_name: 1-23 characters>
		prefixMatch 
			<stringPattern: 1-12 digits, 'X' or 'x' characters>
			<startPosition: 0-11>
			<digitLength: 1-30>

To configure the signaling profile carrierCodeToIoiMappingProfile, use the following syntax:

% set profiles signaling
	carrierCodeToIoiMappingProfile <carrier_code: 4 digits [0-9]>
		accessParam <class | type>
		accessValue <access_value_string: 1-64 characters>
		ioi <inter_operator_identifier_string: 1-128 characters>

To configure the signaling profile ioiToCarrierCodeMappingProfile, use the following syntax:

% set profiles signaling
	ioiToCarrierCodeMappingProfile <inter_operator_identifier_string: 1-128 characters>
		carrierCode <carrier_code: 4 digits [0-9]>

To configure the signaling profile sipJJ9030InterworkingProfile, use the following syntax:

% set profiles signaling
	sipJJ9030InterworkingProfile <sip_JJ9030_Interworking_Profile_name: 1-23 characters>
		addUserEqualPhoneforDivHiInterworking <disabled | enabled>
		bciCalledPartyCategory <noIndication | ordinary | payphone | spare>
		bciChargeIndicator <charge | noCharge | noIndication | spare>
		bciTerminatingIsdnAccess <isdn | nonIsdn>
		chargeAreaInformation <charge_area: 5 digits [0-9]>
		origIoi <originating_inter_operator_identifier_string: 1-128 characters>
		originatingCarrierCode <originating_carrier_code: 4 digits [0-9]>
		setHiPresentationRestricted <disabled | enabled>
		sipFlavor
			JJ9030
			SIP-T
			SIP-ttc-charging-params
		termIoi <terminating_inter_operator_identifier_string: 1-128 characters>

To configure the parameter contractorNumInterworking under the profile NNIProfile, use the following syntax:

% set profiles signaling NNIProfile <nni_profile_name>
	contractorNumInterworking <disabled | enabled>

To attach the signaling profiles calledPrefixMatchProfile and sipJJ9030InterworkingProfile with sipTrunkGroup, use the following syntax:

% set addressContext <address_context_name> zone <zone_name> sipTrunkGroup <SIP_TG_name> signaling
	calledPrefixMatchProfile <called_prefix_match_profile_name>
	sipJJ9030InterworkingProfile <sip_JJ9030_interworking_profile_name>

Command Parameters

The parameter descriptions for profiles signaling calledPrefixMatchProfile are as follows:

The parameter descriptions for profiles signaling carrierCodeToIoiMappingProfile are as follows:

The parameter descriptions for profiles signaling ioiToCarrierCodeMappingProfile are as follows:

The parameter descriptions for profiles signaling sipJJ9030InterworkingProfile are as follows:

The descriptions for new parameters under profiles signaling NNIProfile are as follows:

The descriptions for new parameters under addressContext zone sipTrunkGroup signaling are as follows: