Excerpt |
---|
The EdgeView contains the |
Add_workflow_for_techpubs |
---|
AUTH1 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb41059c, userName='null'} |
---|
JIRAIDAUTH | CHOR-4035 |
---|
REV5 | UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} |
---|
REV6 | UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} |
---|
REV3 | UserResourceIdentifier{userKey=8a00a0c85c46b657015d505775a80024, userName='null'} |
---|
REV4 | UserResourceIdentifier{userKey=8a00a0c86062358001607e0702a30014, userName='null'} |
---|
REV1 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cc7d083d, userName='null'} |
---|
REV2 | UserResourceIdentifier{userKey=8a00a0c86d7a8a62016d81ab2a4a0001, userName='null'} |
---|
|
Excerpt |
---|
The EdgeView Service Control Center (SCC) is in the EdgeView and . The EdgeView SCC can launch an instance's UI in your internet browser, which allows you to configure, operate, and monitor the instance if the remote UI connection is currently active. For example, you can configure the EdgeView Agent (EVAgent) logging and view the current connection and remote UI status of the EdgeView connection. Info |
---|
| To enable this feature for the , you require the EdgeView 16.0.0 1 Release or later. |
To enable the EdgeView SCC, you must configure the EdgeView IP address or FQDN and the EdgeView Management ID. With the EdgeView SCC enabled, the sends a SIP signaling group (SG) and port status report and the most recent, highest severity alarm to the EdgeView. The SIP SG SG and port status report includes information about the SIP SG and port's unique ID, administrative status, and real-time status. Info |
---|
| If a timeout results in the runtime status not being retrieved, then the reports the real-time status as Unknown. |
RequirementsTo enable the EdgeView SCC, you must configure the EdgeView panel (see the following procedure) according to your :- - Configure the EdgeView IP address or FQDN.
- - Configure the EdgeView IP address or FQDN and the EdgeView Management ID.
Note |
---|
| When you enter the EdgeView Management ID, you must insert a colon every two characters (00:00:00). Otherwise, the cannot connect to the EdgeView. |
|
Configure the
...
for EdgeView during Initial SetupTo configure the
for EdgeView SCC during your initial setup, refer to
one of the
following procedures:...
When you configure the Initial Ribbon SBC SWe Lite Setup screen, use the following table to configure the EdgeView panel.
Caption |
---|
0 | Table |
---|
1 | EdgeView Parameters |
---|
|
Parameter | Description |
---|
EdgeView | Configure this field to enable or disable the EdgeView SCC. - No (default) - The EdgeView is disabled.
- Yes - The EdgeView is enabled.
| EdgeView Address | Configure this field with the IP address or FQDN of the EdgeView. Note: This field applies only when the EdgeView field is set to Yes. | EdgeView Management ID | Caution: When you enter the EdgeView Management ID, you must insert a colon every two characters (00:00:00). Otherwise, the cannot connect to the EdgeView.Configure this field with the Management ID of for the EdgeView. Note: This field applies only to the . The automatically sends the MAC address to the EdgeView.Note: This field applies only when the EdgeView field is set to Yes. |
|
Caption |
---|
0 | Figure |
---|
1 | SBC 1000/2000 EdgeView in Initial Ribbon Setup Screen - Enabled |
---|
|
Image Added |
Note |
---|
|
When you enter the EdgeView Management ID, you must insert a colon every two characters (00:00:00). Otherwise, the cannot connect to the EdgeView. |
Caption |
---|
0 | Figure |
---|
1 | SBC SWe Lite EdgeView in Initial Ribbon Setup Screen - Enabled |
---|
|
|