Note
Windows and/or dialog boxes depicted in this section are intended as examples only and may not reflect the actual software/firmware versions applicable to you. Refer to your hardware/software requirements relevant release note for software/firmware version details.
In this section:
The ConnexIP Operating System jump start installation is required for cases such as reverting to older releases or SSD drive replacement. To re-install the ConnexIP OS, follow the procedure below.
Note
The ConnexIP ISO installation procedure automatically copies the SBC application package to the SBC platform, and takes about 30 to 40 minutes to complete.
Note
When using the Java Console, ensure that Java version 8 (or lower) is installed on the target machine. The SBC does not support higher than version 8.
Downloading the ConnexIP ISO Image
Download the ConnexIP OS files bundles from the Ribbon Support Portal. The file bundles below are examples, where N is the release number and x is the build number. To determine the exact OS versions, refer the appropriate release notes at SBC Release Information.
- sbc-V0N.0N.0NR0xx-connexip-os_0N.0x.xx-R0xx_amd64.iso
- sbc-V0N.0N.0NR0xx-connexip-os_0N.0x.xx-R0xx_amd64.iso.md5
Refer to Downloading Software from the Ribbon Support Portal.
Reinstalling the OS
Note
Reinstalling the OS will format your disk and erase all data. Ribbon strongly recommends saving configuration data to a remote server before reinstalling the OS in the event you need to restore the original configuration data after the re-installation.
The following procedure describes how to reinstall the ConnexIP OS:
Launch the host remote console through the BMC. Refer to Launching the Remote Console from the BMC.
Select Media in the JViewer and click Virtual Media Wizard.
Virtual Media Wizard
The Virtual Media screen appears. Select ISO Image from the CD/DVD Media1 section of the screen.
Virtual Media Screen
Click Browse. From the Open dialog, browse to and select the connexip-os_<version>_amd64.iso file and click Open.
Open Dialog Screen
Click Connect CD/DVD. A message Device redirected in Read Only Mode appears on the screen. Click OK to continue. This mounts the ISO image from your local desktop or laptop.
Mounting Virtual CD/DVD
- Click Close to exit the window.
- Minimize the JViewer window.
On the SBC BMC GUI, navigate to Remote Control > Server Power Control. The Power Control and Status window is displayed.
Observe that the "Host is currently on" message is in the window.Server Power Control Window
Select the Power Off Server-Orderly Shutdown option and click Perform Action. This action brings the SBC host down.
Server Power Control - Off Option
Once the SBC host is down, from the same location, select Power On Server and click Perform Action. This action powers on and reboots the SBC host.
Server Power Control - On
Once the BMC is up and running, access the JViewer window.Press <DEL> or <F2> immediately, when the splash screen appears.
BIOS Splash Screen
The BIOS setup utility screen is displayed.
Use the right arrow key to navigate to the Save & Exit menu.
BIOS Setup Utility
Select AMI Virtual CDROM0 1.00 from the Save & Exit menu to boot from the virtual CD drive. This instructs the server to boot from the redirected ConnexIP OS ISO image.
Booting from Virtual CD Drive
Select Install and press <Enter> to start the installation.
ConnexIP Installer Boot Menu
The automated installation process starts. This process takes approximately 30 to 40 minutes.
Partitions Formatting Screen
Installing the Base System
Selecting and Installing Software
Copying SBC Package
Running Post Install
Once the installation is complete, the disk partition upgrade starts. At this stage, DO NOT power off the system.Disk Partitioning
Once the system reboots, the ConnexIP login screen appears on the screen.ConnexIP Login Screen
This concludes the ConnexIP OS installation/re-installation process.
Close the JViewer window.
Continue to install the desired SBC application build. Refer to Installing SBC Application.
Overview
Content Tools