Use the following workflow to deploy a partially configured signaling group and a new single endpoint using the SBC Easy Configuration Wizard.

The analog module of the Edge 8300 model needs this configuration to transmit and receive calls from the device's analog ports. The configuration includes setting up the SBC SWe Edge function inside the 8300 to act as the User Agent (UA) server for telephone devices connected to those analog ports.

  • For this single endpoint scenario, since the peer end is not known or is not configured, the Easy Configuration Wizard creates the Transformation and Routing entries for the endpoint being configured independent of the peer end. (If you connect two endpoints and then use the Single Leg Wizard to add a third endpoint, you must create or modify the Transformation and Routing entries to complete the routing.)
  • Refer to Using the Easy Configuration Wizard in the SBC Edge documentation for an overview of the Easy Config routine. Refer to Workflow for Initial Setup - Standalone or Workflow for Initial Setup - High Availability for the complete instructions for a new Edge 8000 setup.
Easy Configuration Wizard - Single Leg Configuration Notes
  • Use the Single Leg Wizard to add a 3rd, 4th, or 5th peer to the device when at least two legs have already been configured via the standard Easy Configuration Wizard.
  • Emergency configuration is not supported for single end-point scenarios.

Prerequisites

  • Completion of the initial setup procedures in Workflow for Initial Setup. This includes physically installing the device, configuring the initial platform settings, and installing the SBC SWe Edge license.
  • Login access to the SBC SWe Edge WebUI as user administrator (admin).

Workflow

StepAction
1Log in and Start the Easy Configuration
2Step 1 – Select the Edge 8K Scenario
3Step 2 – Configure Edge 8K for Endpoint
4Step 3 – Confirm and Execute the Provisioning

Log in and Start the Easy Configuration

  1. From the SBC SWe Edge WebUI, log in as user administrator (admin).

  2. Follow the prompts to change the password, and then log in again.
    Refer to First-Time Login Passwordsfor the initial (default) passwords.

  3. Once in the WebUI, click the Tasks tab.
  4. In the navigation pane on the left, select SBC Easy Setup > Easy Config Wizard.
    Step 1 of the Easy Configuration appears.

Select the Edge 8K Scenario – Step 1

Step 1 of Easy Configuration includes the selection and provisioning of the Edge 8000 scenario and the selection of the Edge 8000 device type.

  1. In the Scenario Parameters panel, from the Application dropdown, list select Edge 8K.

  2. Complete the following fields.

    FieldDescription
    ApplicationSelect Edge 8K.
    Scenario DescriptionEnter a name to describe the setup.
    Telephone CountryEnter the Country in which the IP PBX is setup.
    SIP SessionsEnter the number of simultaneous SIP Sessions. Valid entries: 1 - 1200.
    EDGE 8K Variants

    Select the model of the device you are configuring.

    Example for the Edge 8300 device: 

    • 8300 22S 2X (for the 8300 model with 22 FXS ports and 2 FXO ports)
  3. Click Next to advance to Step 2 of Easy Configuration.

Configure Edge 8K for Endpoint – Step 2

Step 2 includes the configuration of the Edge 8000 endpoint.

  1. Enter the UA Server FQDN or IP address.
    This is the FQDN or IP address of the User Agent (UA) server resident in the Edge 8300 device.
    The port numbers of the FXS, FXO, and PRI ports (as applicable) also appear in the Step 2 menu for reference.
  2. Click Next to advance to Step 3 of Easy Configuration.

Confirm the Configuration – Step 3

Step 3 allows you to review a summary before executing the provisioning.

  1. Review the information and click Finish.
  2. Read the continuation statement that asks you to configure the routes before attempting to make calls, and click OK.
  3. Read the confirmation statement that says the System Configuration is complete, and click OK.