SBC 1000
# | Name | Description |
|---|---|---|
1 | Reset | System reset button. For more information, see Resetting SBC Edge to Factory Defaults. |
2 | USB Ports | USB ports for Sonus SBC 1000/2000 main board — see USB Ports detail section below |
3 | Power | |
4 | Alarm | |
5 | Peer Node | Peer Node Status LED (also recognized as the Locator LED) |
6 | Ready | |
7 | Ethernet Port 1 - 3 | Ethernet Ports 1, 2 and 3. |
| 8 | USB Ports | USB ports for the Application Service Module (ASM) (when installed) |
| 9 | Ethernet Port Status | Ethernet Status LED |
| 10 | DS1 Ports | T1/E1 ports (when installed) |
SBC 1000 With ASM
# | Name | Description |
|---|---|---|
1 | Reset | System reset button. For more information, see Resetting SBC Edge to Factory Defaults. |
2 | USB Ports | USB ports for Sonus SBC 1000/2000 main board — see USB Ports detail section below |
3 | Power | |
4 | Alarm | |
5 | Peer Node | Peer Node Status LED (also recognized as the Locator LED) |
6 | Ready | |
7 | Ethernet Port 1 - 3 | Ethernet Ports 1, 2 and 3. |
| 8 | USB Ports | USB ports for the Application Service Module (ASM) (when installed) |
| 9 | Ethernet Port Status | Ethernet Status LED |
| 10 | DS1 Ports | T1/E1 ports (when installed) |
SBC 1000 With Dual T1/E1
# | Name | Description |
|---|---|---|
1 | Reset | System reset button. For more information, see Resetting SBC Edge to Factory Defaults. |
2 | USB Ports | USB ports for Sonus SBC 1000/2000 main board — see USB Ports detail section below |
3 | Power | |
4 | Alarm | |
5 | Peer Node | Peer Node Status LED (also recognized as the Locator LED) |
6 | Ready | |
7 | Ethernet Port 1 - 3 | Ethernet Ports 1, 2 and 3. |
| 8 | USB Ports | USB ports for the Application Service Module (ASM) (when installed) |
| 9 | Ethernet Port Status | Ethernet Status LED |
| 10 | DS1 Ports | T1/E1 ports (when installed) |
SBC 1000 With ASM and Dual T1/E1
# | Name | Description |
|---|---|---|
1 | Reset | System reset button. For more information, see Resetting SBC Edge to Factory Defaults. |
2 | USB Ports | USB ports for Sonus SBC 1000/2000 main board — see USB Ports detail section below |
3 | Power | |
4 | Alarm | |
5 | Peer Node | Peer Node Status LED (also recognized as the Locator LED) |
6 | Ready | |
7 | Ethernet Port 1 - 3 | Ethernet Ports 1, 2 and 3. |
| 8 | USB Ports | USB ports for the Application Service Module (ASM) (when installed) |
| 9 | Ethernet Port Status | Ethernet Status LED |
| 10 | DS1 Ports | T1/E1 ports (when installed) |
Ports
Usage
The Sonus SBC 1000 sports two pairs of USB ports (as illustrated above) — each pair serves a particular purpose:
Location | USB Port Intent and Usage Detail |
|---|---|
2
| These ports are optionally used to attach an external USB drive to store core dumps for troubleshooting (in the event they occur), and as a survivability mechanism for Active Directory Caching (when configured). See Support section below for proper usage. |
8
| If your Sonus SBC 1000 has a built-in Application Service Module (ASM), this USB port is primarily used for Updating the ASM Recovery Partition, and to (optionally) transfer files between a USB drive and the ASM. |
Support
The following section is applicable only to the USB ports on location #2 on the Sonus SBC 1000's front panel.
For the Sonus SBC 1000/2000 system to properly recognize the USB thumb drive, you must ensure the following prerequisites are satisfied:
- The USB storage must be of FAT32 file format.
- The storage must be at least 1GB (or more) in size.
- The SBC does not require a reboot after the USB drive is installed.
Overview
Content Tools