You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 3 Current »

The Call Accounting Manager (CAM) generates Call Detail Records (CDRs) and supports accounting event logging on the

Unable to show "metadata-from": No such page "_space_variables"
. As calls traverse the
Unable to show "metadata-from": No such page "_space_variables"
, CDRs are generated and stored in the /var/log/sonus/sbx/evlog directory. You can view these CDR by looking at files with the “.ACT” extension. It is useful to view the ACT logs during call debugging (to get the originating trunk group, calling and called numbers, codec used, and more). You can also view billing records (and other logs) while in EMA Platform Mode. Refer to Administration - Accounting and Logs for more information. 


Note

The SBC generates timestamps in the local time format in the ACT files for any of the fields that were previously in the GMT time format.


You can send 

Unable to show "metadata-from": No such page "_space_variables"
 accounting records to three different types of locations:

  1. Local hard disk: If accounting is enabled, then ASCII records are always written to the local disk.
  2. An external server, for example: 
    1. To a DSI-L0 server: If configured, the ASCII records can be transferred to an external
      Unable to show "metadata-from": No such page "_space_variables"
       DSI server using SFTP.
    2. To an external billing server in an IMS network via the Rf Interface.
  3. RADIUS server: RADIUS accounting records can be generated and sent to an external RADIUS server.

Call Detail Record Format

This section describes the ASCII and streaming Call Detail Record (CDR) format.


The SBC may insert non-ASCII characters in CDRs when messages are parsed in the initial INVITE.

Various

Unable to show "metadata-from": No such page "_space_variables"
 elements such as GSX 9000, PSX, and
Unable to show "metadata-from": No such page "_space_variables"
 use many of the same CDR fields. Because of this, some fields in the “Accounting Records” table below do not apply to
Unable to show "metadata-from": No such page "_space_variables"
 call details, but instead simply indicate pass-though type messages (for example, ISUP and PSTN fields).

For GW-GW calls on the

Unable to show "metadata-from": No such page "_space_variables"
and 
Unable to show "metadata-from": No such page "_space_variables"
Cloud, a CDR is only generated for the ingress leg. If the generation mode is configured as origination and the populateRemoteGsxInfoState flag is enabled, the SBC logs billing information from the termination node.

The “Service Group” object is not applicable to the
Unable to show "metadata-from": No such page "_space_variables"
. Any references to “Service Group” must be mapped to “Trunk Group”.

For more information on known limitations, refer to the applicable release notes at SBC Release Information page.

Additional references:

Accounting File Version

The CAM version of the SBC 12.00.00 is 103.00.00 (major CAM version is 103, minor CAM version is 0, special CAM version is 0). The associated hex format of CAM file version is  00670000, displayed as "00670000" in ASCII CAM file header below:

Sonus Networks, Inc.00000000FF600000670000000000000128V12.00.00R000 0000000000000000000000000000ACT2023041023333000000000000000

File Header

Every event log file, including accounting logs, contains a file header. This header consists of a 128-character string terminated by a (line feed). Each field in the event log file header is defined in the following table:


Field Offset

Field Length

Field Content

0

20

ASCII OEM string, blank padded, (for example "Ribbon Communications, Inc.")

20

8

Reserved

28

2

Old CAM File Version. Always "FF".

30

2

Hex offset to the Event Log Type, or the number of bytes from the beginning of the record to the beginning of the Event Log Type field (in the above example, "64").

32

2

Reserved

34

8

New CAM File Version. This value is 100, and consists of:

  • 0064 0000—the 4-digit hex value of decimal value 100. This field is incremented with major
    Unable to show "metadata-from": No such page "_space_variables"
    releases.
  • Minor CAM Version of "00"—This field is incremented when accounting changes are introduced in minor
    Unable to show "metadata-from": No such page "_space_variables"
    releases.
  • Special CAM version of "00"—This field is incremented when accounting changes are introduced in special builds of major
    Unable to show "metadata-from": No such page "_space_variables"
    releases.

42

8

Reserved

50

4

Hex offset to start of data. In this example, "0128".

54

13

Unable to show "metadata-from": No such page "_space_variables"
software revision. In this example, "V10.01.00R000".

67

29

Reserved

96

3

Event Log Type (same as file extension). In this example, "ACT".

99

16

File creation time.

115

12

Reserved

127

1

Header terminator (line feed)

File Footer

The following line footer is appended to each log file (including accounting logs) when the file is closed under controlled conditions for non-CNF environments:

MMDDYYYY HHMMSS: File administratively closed.

Controlled conditions include CLI commands (for example, set oam eventLog typeAdmin acct rolloverAction...) and automatic roll-overs when maximum file size is reached.

When an uncontrolled file closure occurs, such as an

Unable to show "metadata-from": No such page "_space_variables"
 switch-over or system failure, this footer may not be present.

File Footer - CNF

For CNF environments, the following line footer is appended to each log file:

YYYY-MM-DD HH:MM:SS ZONE File administratively closed.

For backward compatibility of the logging format, a CLI configuration is added for the debug, system, and security logs. You can switch the files of these log formats at runtime using the following CLI commands:

% set oam eventLog typeAdmin debug cnfLogFormat <disable | enable>
% set oam eventLog typeAdmin system cnfLogFormat <disable | enable>
% set oam eventLog typeAdmin security cnfLogFormat <disable | enable>
Note
  • By default, the cnfLogFormat flag is enabled in the CNF environment and disabled in non-CNF environments.
  • You can configure the debug, system, and security formats to have the new CNF log format based on this flag.
  • The trace and pkt files always follow the old format.
  • The audit and mem files always follow the new format.

Renaming Open Accounting Files

The SBC includes the ability to rename a currently-open accounting file using a known suffix to make it easily identifiable by external applications. To activate this feature, simply enable the flag “Rename Open Files” using EMA GUI or CLI. 

CLI syntax example:

% set oam eventLog typeAdmin acct renameOpenFiles enable

Once this flag is enabled, on the next accounting file open activity, the suffix .OPEN is appended to the filename using the format <shelf><sequence number>.ACT.OPEN (currently open files are not affected).

For example, as accounting file 1000099 is created with this feature already enabled, the file is named “1000099.ACT.OPEN”.

If a file closes due to a rollover, logging shutdown or system shutdown, it is renamed to the original format: <shelf><sequence number>.ACT.

For configuration details, refer to:

Accounting File Roll-Over

The 

Unable to show "metadata-from": No such page "_space_variables"
application maintains a configurable maximum of up to 2048 accounting files. Once the configured limit of files is reached, the application deletes the oldest files first to accommodate the new files.

When accounting file names reach the maximum value of 1FFFFFF.ACT, the next file name rolls over to 1000001.ACT. Use the “Rename Open Files” flag to rename the most recent accounting file with the ”ACT.OPEN” extension. This flag is accessible from the EMA at “System Configuration” > “CDR and Servers” tab.

Global Charge Reference

The Global Charge Reference (GCR) feature allows correlation of calls across networks where the calls are originated from and terminated at different third-party devices. The GCR field is populated in the CDRs of the SBC if the GCR is received in a gateway protocol message from a GSX9000.

The GSX9000 receives or generates the GCR parameter through an ISUP parameter. The GCR is used in conjunction with SIP call-id’s to associate calls that interwork between SIP and ISUP protocols across multiple network devices.

How to Set Up SFTP from the SBC to a CDR Server

If a CDR server is configured, the 

Unable to show "metadata-from": No such page "_space_variables"
transfers the files through SFTP to the configured destination.

  1. To create a CDR server, use the following command syntax:

    % set oam accounting cdrServer admin [primary | secondary] connectionTimeout <numeric: 15 to 600 seconds> filePrefix <name of SBC> ipAddress <ip address> password <password for ftp user> path <directory to ftp to> transferTimeout <numeric: 15 to 600 seconds> username <username of ftp user>



    An example to show the CDR server configuration and check the configuration is as follows:


    admin@SBC01> config
    admin@SBC01% set oam accounting cdrServer admin primary connectionTimeout 15 filePrefix SBC01 ipAddress 10.10.211.10 password sonus path /export/home/SBC01ACTrecs/ transferTimeout 15 username root
    admin@SBC01% commit
    admin@SBC01% quit
    
    admin@SBC01> show table oam accounting cdrServer admin
                                                                                    FILE    CONNECTION  TRANSFER
    TYPE     IP ADDRESS    USERNAME  PASSWORD         PATH                          PREFIX  TIMEOUT     TIMEOUT
    --------------------------------------------------------------------------------------------------------------
    primary  10.10.211.10  root      $3$qaO71mBy8l8=  /export/home/SBC01ACTrecs/  SBC01   15          15
    [ok][2013-10-02 06:14:49]
    admin@SBC01>


  2. Initially, the accounting field is not set to ftp or automatically roll over. Use the following command to view Rollover settings for accounting (See "acct" row in the example):

    > show table oam eventLog typeAdmin
                                    MESSAGE                ROLLOVER                                     FILE               RENAME    DISK                           SYSLOG
                       FILE   FILE  QUEUE    SAVE  FILTER  START     ROLLOVER                 ROLLOVER  WRITE    SYSLOG    OPEN      THROTTLE  EVENT LOG   SERVER   REMOTE
    TYPE      STATE    COUNT  SIZE  SIZE     TO    LEVEL   TIME      INTERVAL  ROLLOVER TYPE  ACTION    MODE     STATE     FILES     LIMIT     VALIDATION  NO       HOST
    ----------------------------------------------------------------------------------------------------------------------------------------------------------------------
    system    enabled  32     2048  10       disk  major   -         0         nonrepetitive  stop      default  disabled  disabled  5000      disabled    server1  0.0.0.
    debug     enabled  32     2048  10       disk  major   -         0         nonrepetitive  stop      default  disabled  disabled  -         disabled    server1  0.0.0.
    trace     enabled  32     2048  10       disk  info    -         0         nonrepetitive  stop      default  disabled  disabled  -         disabled    server1  0.0.0.
    acct      enabled  32     2048  10       disk  major   -         0         nonrepetitive  stop      default  disabled  disabled  -         disabled    server1  0.0.0.
    security  enabled  32     2048  10       disk  major   -         0         nonrepetitive  stop      default  disabled  disabled  -         disabled    server1  0.0.0.
    audit     enabled  32     2048  10       disk  info    -         0         nonrepetitive  stop      default  disabled  disabled  -         disabled    server1  0.0.0.
    packet    enabled  32     2048  10       disk  major   -         0         nonrepetitive  stop      default  disabled  disabled  -         disabled    server1  0.0.0.
    memusage  enabled  32     2048  10       disk  major   -         0         nonrepetitive  stop      default  disabled  disabled  -         disabled    server1  0.0.0.
    [ok]



  3. To create the accounting file rollover and ftp, use the following command syntax:

    % set oam eventLog typeAdmin acct rolloverStartTime <CCYY-MM-DDTHH:MM:SS> rolloverInterval <number of seconds between each file rollover> rolloverType repetitive rolloverAction start
    where 'T' in 'DDTHH' is a constant used to indicate the Time follows.



    An example of the configuration and display of the accounting file rollover and ftp is as follows:


    % set oam eventLog typeAdmin acct rolloverStartTime 2018-09-13T06:30:00 rolloverInterval 500 rolloverType repetitive rolloverAction start
    [ok][2018-08-13 12:58:11]
    
    [edit]
    admin@SBXUK11-1% commit
    Commit complete.
    [ok][2018-08-13 12:58:14]
    
    [edit]
    admin@SBXUK11-1% exit
    
    > show table oam eventLog typeAdmin
                                    MESSAGE                                                                              FILE               RENAME    DISK
                       FILE   FILE  QUEUE    SAVE  FILTER                             ROLLOVER                 ROLLOVER  WRITE    SYSLOG    OPEN      THROTTLE  EVENT LOG
    TYPE      STATE    COUNT  SIZE  SIZE     TO    LEVEL   ROLLOVER START TIME        INTERVAL  ROLLOVER TYPE  ACTION    MODE     STATE     FILES     LIMIT     VALIDATION
    ----------------------------------------------------------------------------------------------------------------------------------------------------------------------
    system    enabled  32     2048  10       disk  major   -                          0         nonrepetitive  stop      default  disabled  disabled  5000      disabled
    debug     enabled  32     2048  10       disk  major   -                          0         nonrepetitive  stop      default  disabled  disabled  -         disabled
    trace     enabled  32     2048  10       disk  info    -                          0         nonrepetitive  stop      default  disabled  disabled  -         disabled
    acct      enabled  32     2048  10       disk  major   2018-09-13T06:30:00-00:00  500       repetitive     start     default  disabled  disabled  -         disabled
    security  enabled  32     2048  10       disk  major   -                          0         nonrepetitive  stop      default  disabled  disabled  -         disabled
    audit     enabled  32     2048  10       disk  info    -                          0         nonrepetitive  stop      default  disabled  disabled  -         disabled
    packet    enabled  32     2048  10       disk  major   -                          0         nonrepetitive  stop      default  disabled  disabled  -         disabled
    memusage  enabled  32     2048  10       disk  major   -                          0         nonrepetitive  stop      default  disabled  disabled  -         disabled
    [ok]



  4. View CDR Server status using the following command:

    admin@SBC01> show table oam accounting cdrServer status
                               SUCCESSFUL  FAILED     PENDING
    TYPE     STATE   PROGRESS  TRANSFERS   TRANSFERS  TRANSFERS
    -------------------------------------------------------------
    primary  active  done      3           0          0
    [ok][2013-10-02 07:27:19]



  5. Verify that the files were transferred to the FTP server by logging in to the CDR server and executing the following command:

    ftp server:
    root@hostname # pwd
    /export/home/SBC01ACTrecs
    root@hostname # ls -l
    total 708
    -rw-r--r--   1 root     other     346730 Oct  2 06:45 SBC01.20131002064500.1000022.ACT
    -rw-r--r--   1 root     other        175 Oct  2 07:00 SBC01.20131002070000.1000023.ACT
    -rw-r--r--   1 root     other        175 Oct  2 07:15 SBC01.20131002071500.1000024.ACT
    root@hostname #



  6. Execute the following command to view the successful and failed CDR file transfer:

    % show table oam accounting cdrServer status
                               SUCCESSFUL  FAILED     PENDING
    TYPE      STATE  PROGRESS  TRANSFERS   TRANSFERS  TRANSFERS
    ---------------------------------------------------------
    primary   active  done     2           0          0
    secondary standby idle     0           7          0

CDR Server Remote Port Configuration

The 

Unable to show "metadata-from": No such page "_space_variables"
 supports transferring call accounting files (.ACT) to a CDR server through a user-configured port. The 
Unable to show "metadata-from": No such page "_space_variables"
 also supports using Secure Shell (SSH) public keys instead of password to authenticate with the remote CDR server.

Use the following parameters within CDR server configuration to set up remote port and ssh key based authentication:

  • cdrPort
  • useSshKeyFile 
  • generateSshPublicKeys

You can either use the existing username/password or the SSH public key to authenticate with the remote CDR server. The parameter useSshKeyFile must be enabled to generate the SSH public key.

To generate a new SSH public key, execute the following command:

% request oam accounting cdrServer admin primary generateSshPublicKeys

The generated SSH public key must be installed on CDR server to use ssh key based authentication from SBC. The SSH public key must be copied to the remote CDR server file /home/<user>/.ssh/authorized_keys. If the private key is compromised, the key must be re-generated. Once the key is re-generated, the CDR server must be updated with the new key.

  • The SSH public key generated for the primary CDR server can also be used to authenticate the secondary CDR server. The SSH public key can be installed on both primary and secondary CDR servers.
  • The configured user must have access to /home/<user>/.ssh for reading the public key.

Configuring the CDR Server Remote Port

When downloading billing records (or other logs), you must use port 2024 to SFTP files from the 

Unable to show "metadata-from": No such page "_space_variables"
.

% set oam accounting cdrServer admin primary cdrPort 2024

Using SSH Public Keys for CDR Server Authentication

 Using SSH public keys for CDR server authentication requires the following:

  1. Enabling SSH Key Based Authentication
  2. Generating the SSH Public Key
  3. Copying and Installing the SSH Public Key to CDR Servers

Enabling SSH Key Based Authentication

To enable SSH key based authentication, execute the following command:

% set oam accounting cdrServer admin primary useSshKeyFile Enable

Generating the SSH Public Key

To generate a new SSH public key, execute the following command:

% request oam accounting cdrServer admin primary generateSshPublicKeys
result success
reason 
ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAAABAQDclSOlVfVmmhatw5bDQRk7AaYvCRUUfHHbSvkCBb4T8zYdJ8JNw15rMSKk9hEkVdtEEZRJU4Q97C+3LbPknZrIMM+zmSRYmh2/LkGAlydSJ+sPe9i7zWFOLYeA3gitaKJSPgSjdb4WGgDq686Ei4yup9xYDbT8wAcosQsf3tfbqH2GetNJ8tAs3KjRi7FPhH1hHdXVyH0yW1mdGlMYvoFUeFCRjhE81oJhy2jMTJD9T3eQiJo4NZQZYOgALMQPi8fxaAgnuWmvrejNTn/PgRyGpQEs7HFHkX5zHW5M74PU/Z3S3Y2uSZlYrCQRf9Y2mUiK5R40bjsKz4TqIP5LfzhX
[ok]

Copying and Installing the SSH Public Key to CDR Servers

The SSH public key is copied to the remote CDR server file /home/<user>/.ssh/authorized_keys.

For configuration details, refer to Accounting - CLI.

RADIUS Accounting Support

Remote Authentication Dial In User Service (RADIUS) is a standardized protocol for supporting Authentication, Authorization, and Accounting (AAA) management in a distributed client-server architecture. The 

Unable to show "metadata-from": No such page "_space_variables"
 can map CDR fields and other input parameters to attributes (standard as well as vendor-specific attributes) in RADIUS call-accounting records. The
Unable to show "metadata-from": No such page "_space_variables"
, acting as a RADIUS client, can send the call-accounting records to an external RADIUS server. For a description of Sonus CDR to RADIUS VSA field mapping, refer to CDR to VSA Mapping.

The following accounting message types are supported by RADIUS protocol:

  • Accounting Request
  • Accounting Response

The process for sending accounting requests and responses is described below.

  • The
    Unable to show "metadata-from": No such page "_space_variables"
     sends an accounting-request with Accounting-Status-Type value "Accounting-on". At a later time, this transaction informs the server about the new accounting client that will send the accounting messages to the NAS/resource usage by user.
  • When the
    Unable to show "metadata-from": No such page "_space_variables"
     connects the call, the accounting starts. The accounting-request contains the Accounting-Status-Type with the value "Start". The "Start" records contains the following:
  • User identification
  • Network address
  • Point of attachment
  • Unique session identifier
  • Next, the
    Unable to show "metadata-from": No such page "_space_variables"
     records the status change by NAS to the RADIUS server for this active session. The accounting-request now contains the Accounting-Status-Type with the value "Interim". The interim record usually conveys the current session duration and information on the current data usage.
  • When the user network access is closed, the NAS issues a final Accounting Stop record to the RADIUS server, providing the information on the final usage in the terms of the following:
  • Time
  • Packets transferred
  • Data transferred
  • Reason for disconnect
  • Other information related to the call

The Accounting-Request contains the Accounting-Status-Type with the value "Stop". The primary purpose of this data is to bill the user. The data is also used for statistical purposes and for general network monitoring.


To configure the

Unable to show "metadata-from": No such page "_space_variables"
to send records to an external RADIUS server and to configure up to three RADIUS servers per
Unable to show "metadata-from": No such page "_space_variables"
, refer to Accounting - CLI.

SBC Standard Attributes

The 

Unable to show "metadata-from": No such page "_space_variables"
 RADIUS application uses standard attributes from the RADIUS when possible. For CDR fields that cannot be mapped to the standard attributes, vendor-specific attributes are defined. The 
Unable to show "metadata-from": No such page "_space_variables"
 allows instances of the standard attributes in Accounting request message as per following table:

Table 2: Allowed Standard Attributes


Attribute Name

Attributes description

NAS-IP-Address

The IP Address of the

Unable to show "metadata-from": No such page "_space_variables"
generating accounting request.

NAS -Identifier

The configured NAS Identifier for a given

Unable to show "metadata-from": No such page "_space_variables"
. When sending RADIUS accounting messages, the NAS-Identifier field is populated with the corresponding value configured for the RADIUS server to which message is sent.

Acct-Status-Type

The type of accounting message sent by the

Unable to show "metadata-from": No such page "_space_variables"
. The
Unable to show "metadata-from": No such page "_space_variables"
uses the appropriate value of Acct-Status-Type corresponding to the CDR type to be generated.

  • “Value” field in Acct-Status-Type attribute is “1” when call accounting record type is “START”.
  • “Value” field in Acct-Status-Type attribute is “2” when call accounting record type is “STOP”.
  • “Value” field in Acct-Status-Type attribute is “3” when call accounting record type is “INTERMEDIATE”.
  • “Value” field in Acct-Status-Type attribute is “4” when call accounting record type is “ATTEMPT”.
  • “Value” field in Acct-Status-Type attribute is “5” when call accounting record type is “REBOOT”.
  • “Value” field in Acct-Status-Type attribute is “6” when call accounting record type is “SWITCHOVER”.

Acct-Session-Id

Uniquely identifies accounting records for a given call. It is possible to match all accounting records for a given call when correlating call records.

Acct-Session-Time

The number of seconds during which the user received service (duration of the call).

Acct-Terminate-Cause

The class of termination cause. This value is derived from the disconnect reasons class value.

Rf Interface Support

The

Unable to show "metadata-from": No such page "_space_variables"
acting as a P-CSCF or IBCF supports Rf interface-based offline billing in compliance with standard IMS as well as file-based and stream-based CDRs. The SBC can select either CDR/streaming-based charging or Rf Interface depending on whether the system-wide flag, enableRfApp, is enabled or not. Refer to Signaling - Global - CLI or Signaling - Diam Sig Controls for configuration details.

The

Unable to show "metadata-from": No such page "_space_variables"
Diameter node supports both Rf application along with the existing Rx application. The Diameter node uses "Route Table" to find peer for outbound request based on destination realm and application.

For more details, refer to Rf Interface Support.

Generating CDRs in Q-SBC Format

By default, the SBC Core generates CDRs in the standard SBC Core (former Sonus) format. For deployments that require it, users with admin privileges can configure the SBC Core to generate CDRs in the format of the (former GENBAND) Q-series SBCs. Similar to SBC Core CDRs, the Q-SBC format is an ASCII-format text file with multiple records per file. When you enable the Q-SBC format, the SBC Core populates CDR log files according to the mapping shown in the Q-SBC to SBC Core CDR Mapping table. Refer to Generating CDRs in Q-SBC Format for more information.


  • No labels