In this section:
This section describes
To install and configure the
The recommended hardware and software settings are intended to ensure optimum
The following table lists the server hardware requirements: Server Hardware Requirements Intel Xeon processors (Nehalem micro-architecture or above) with 6 cores and above (processors should support hyper threading). Ribbon recommends using Westmere (or newer) processors for better SRTP performance. These processors have the AES-NI instruction set for performing cryptographic operations in hardware. The supported CPU Family Number is 6 and CPU Model Number must be newer than 26. Refer to Intel Architecture and Processor Identification document for more information. ESXi 6.5 and later releases require approximately two physical cores to be set aside for hypervisor functionality. Number of VMs which can be hosted on a server needs to be planned accordingly. Otherwise, 8 NICs (preferably with SR-IOV capability to support SWe optimizations). Intel x710 NICs are also supported on VMware (ESXi versions 6.5 and above) with SR-IOV enabled. x710 NICs are not supported on Direct I/O or KVM. Number of ports allowed: The Configuration Requirement Processor RAM Minimum 24 GB Hard Disk Minimum 500 GB Network Interface Cards (NICs) Ports
Ribbon recommends the following BIOS settings for optimum performance:
Recommended BIOS Settings for Optimum Performance
BIOS Parameter | Recommended Setting | Details |
---|---|---|
Intel VT-x (Virtualization Technology) | Enabled | For hardware virtualization |
Intel VT-d (Directed I/O) | Enabled | If available |
Intel Hyper-Threading | Enabled | |
Intel Turbo Boost | Enabled | |
CPU power management | Maximum Performance |
For example, the BIOS settings are shown below for HP DL 380p Gen8 servers. For BIOS settings of other servers, refer to the respective vendor website.
BIOS Setting Recommendations for HP DL380p Gen8 Server
BIOS Parameter | Recommended Setting | Default Value |
---|---|---|
HP Power Profile | Maximum Performance | Balanced Power and Performance |
Thermal Configuration | Maximum Cooling | Optimal Cooling |
HW Prefetchers | Disabled | Enabled |
Adjacent Sector Prefetcher | Disabled | Enabled |
Processor Power and Utilization Monitoring | Disabled | Enabled |
Memory Pre-Failure Notification | Disabled | Enabled |
Memory Refresh Rate | 1x Refresh | 2x Refresh |
Data Direct I/O | Enabled | Disabled |
SR-IOV | Enabled | Disabled |
Intel® VT-d | Enabled | Disabled |
The following are the VMware ESXi and VMWare ESXi Requirements The VMware Enterprise Plus license is required for SR-IOV.SBC SWe for VMware – Software Requirements
VMware ESXi Requirements
Software Version Tested and Qualified Version For More Information vSphere ESXi 5.1 or above vSphere Client 5.1 or above VMware Knowledge Base vCenter Server 5.1 or above vCenter Server
For more information, refer to Downloading the SBC SWe Software Package.
The following general recommendations apply to all platforms where SBC SWe is deployed:
Following are recommended VMware ESXi and
Following are recommended VMware ESXi configurations:
Use virtual hardware version 8 and above when creating new VMs (available starting in ESXi 5.x). This provides additional capabilities to VMs such as supporting a VM with up to 1 TB RAM, up to 32 vCPUs, etc.
Use VMware vSphere client to configure the following ESXi host configuration parameters on the Advanced Settings page (see figure below) before installing the
ESXi Advanced Settings
ESXi Parameter | ESXi 5.1 Settings | ESXi 5.5 Settings | ESXi 6.0 Settings | ESXi 6.5 Settings | ||||
---|---|---|---|---|---|---|---|---|
Recommended | Default | Recommended | Default | Recommended | Default | Recommended | Default | |
Cpu.CoschedCrossCall | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 |
Cpu.CreditAgePeriod | 500 | 3000 | 1000 | 1000 | 1000 | 1000 | 1000 | 3000 |
DataMover.HardwareAcceleratedInit | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 |
DataMover.HardwareAcceleratedMove | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 |
Disk.SchedNumReqOutstanding | 256 | 32 | n/a | n/a | n/a | n/a | n/a | n/a |
Irq.BestVcpuRouting | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 |
Mem.BalancePeriod | 0 | 15 | 0 | 15 | n/a | n/a | n/a | n/a |
Mem.SamplePeriod | 0 | 60 | 0 | 60 | n/a | n/a | n/a | n/a |
Mem.ShareScanGHz | 0 | 4 | 0 | 4 | 0 | 4 | 0 | 4 |
Mem.VMOverheadGrowthLimit | 0 | 4294967295 | 0 | 4294967295 | 0 | 4294967295 | 0 | 4294967295 |
Misc.TimerMaxHardPeriod | 2000 | 100000 | 2000 | 100000 | 2000 | 100000 | 2000 | 500000 |
Misc.TimerMinHardPeriod | 100 | 100 | n/a | n/a | n/a | n/a | n/a | n/a |
Net.AllowPT | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 1 |
Net.MaxNetifRxQueueLen | 500 | 100 | 500 | 100 | 500 | 100 | 500 | n/a |
Net.MaxNetifTxQueueLen | 1000 | 500 | 1000 | 500 | 1000 | 500 | 1000 | 2000 |
Net.NetTxCompletionWorldlet | 0 | 1 | 0 | 1 | n/a | n/a | n/a | n/a |
Net.NetTxWordlet | 0 | 2 | 1 | 2 | 1 | 2 | 1 | n/a |
Numa.LTermFairnessInterval | 0 | 5 | 0 | 5 | 0 | 5 | 0 | 5 |
Numa.MonMigEnable | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 |
Numa.PageMigEnable | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 |
Numa.PreferHT | 1 | 0 | 1 | 0 | 1 | 0 | 1 | 0 |
Numa.RebalancePeriod | 60000 | 2000 | 60000 | 2000 | 60000 | 2000 | 60000 | 2000 |
Numa.SwapInterval | 1 | 3 | 1 | 3 | 1 | 3 | 1 | 3 |
Numa.SwapLoadEnable | 0 | 1 | 0 | 1 | 0 | 1 | 0 | 1 |
ESXi Parameters
The following configurations are recommended to improve performance.
Configure the VM Latency Sensitivity setting to High in VM Options > Advanced configurations as shown below:
VM Options Window
Limit instances to using cores from a single NUMA by configuring the numa.nodeaffinity option according to the number of the NUMA node the VM is on. Access this option using the path: VM Options > Advanced > Configuration Parameters > Edit Configuration For example, in the following figure the Numa node is 0.
Configuration Parameters Window
VM Configuration Recommendations
Settings | Recommended Configuration |
---|---|
vCPU | Minimum 4 vCPUs required. Any number of vCPUs may be configured depending upon the call capacity requirements, but the number should be even (4, 6, 8, etc.) to avoid impacting performance. Keep the Resource Allocation setting marked as 'unlimited.' Refer to Adjusting Resource Allocations for a VM for more information on setting CPU-related parameters. |
vRAM | Keep the Resource Allocation setting marked as 'unlimited'. Reserve the memory based on call capacity and configuration requirements. Refer to SBC SWe Performance Metrics for supported call capacities with different configuration limits. |
Virtual Hard Disk | Set Hard Disk (virtual) size as 100 GB or more (based on requirements of retaining CDRs, logs, etc. for number of days)
|
vNICs | Set number of virtual NICs as 4 (1-MGMT, 1-HA, 1-PKT0 and 1-PKT1).
|
vSwitch settings |
|
Make sure the Processors, ESXi version and VM configuration (vCPUs, vRAMs, Virtual Hard Disk, vNICs, and vSwitch Settings) must be identical for SBC SWe HA pair.
Make sure that the BIOS and ESXi settings and recommendations must not be changed once it is applied on the server.