egressIpAttributes - SIP - CLI

In this section:

This section lists CLI commands to configure various SIP egress IP attributes involved in sending a call in the forward direction to the peer.

BCI

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes bci 
	bciInterworkEncountered <disable | enable> 
	bciIsdnAddess <disable | enable>

Command Parameters

BCI Parameters

Parameter Description

bci

Use this object to configure Backward Call Indicator (BCI) for Egress IP attributes.

bciInterworkEncountered – Enable flag to indicate that ISUP is interworking with a network which is not capable of providing as many services as ISUP does. ISUP networks will therefore not employ certain features they otherwise normally would, including potentially the use of ISDN cause codes in failure conditions .
- disable (default)
- enable
bciIsdnAddess – Enable flag to enable ISDN Address in the BCI parameter of backward SS7 messages (e.g. ACM or ANM).
- disable (default)
- enable

Domain Name

Use this object to specify use of domain names.

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes domainName 
	useIpSignalingPeerDomainInRequestUri <disable | enable> 
	useSipDomainNameInFromField <disable | enable> 
		preserveIngressFromDomainName <disable | enable> 
		useLowerCaseDomainNames <disable | enable> 
	useSipDomainNameInRequestUri <disable | enable> 
		preserveIngressRUriDomainName <disable | enable> 
		useLowerCaseDomainNames <disable | enable> 
	useZoneLevelDomainNameInContact <disable | enable>

	useZoneLevelDomainNameInPathHdr <disable | enable>

Command Parameters

Domain Name Parameters

Parameter	Description
`useIpSignalingPeerDomainInRequestUri`	Enable flag to use IP Signaling Peer Domain in Request URI. `disable` (default) `enable`
`useSipDomainNameInFromField`	By default, Unable to show "metadata-from": No such page "_space_variables" uses its IP address as the host-port of the FROM URI in the outgoing INVITE message. Enable flag to use the originating gateway information returned in the policy response as the host-port of the FROM URI in the outgoing INVITE message. `disable` (default) `enable` When `useSipDomainNameInFromField` is enabled, the following parameters are available: `preserveIngressFromDomainName` – If a SIP domain is configured for the ingress trunk group and this flag is enabled, the default gateway associated with that SIP domain will be the originating gateway. Otherwise, the originating gateway will be the default gateway associated with the SIP domain associated with the Softswitch entity. `disable` (default) `enable` `useLowerCaseDomainNames` – Set flag to allow lower case domain name. `disable` (default) `enable` The above two flags only apply when a `domainName` is configured for this zone (see Zone - CLI page).
`useSipDomainNameInRequestUri`	Use this flag to indicate how to treat SIP Domain name in outgoing SIP INVITE. `disable` – Unable to show "metadata-from": No such page "_space_variables" includes the IP address in the host-port portion of the Request-URI in outgoing SIP INVITE messages. `enable` – Unable to show "metadata-from": No such page "_space_variables" includes the trunk group domain associated with egress trunk group as destination domain name in outgoing SIP INVITE messages. When `useSipDomainNameInRequestUri` is enabled, the following parameters are available: `preserveIngressRUriDomainName` – Preserve Ingress R-URI Domain Name Flag. When enabled, the ERE/ Unable to show "metadata-from": No such page "_space_variables" uses domain name received in the Request-URI as destination domain name in outgoing SIP INVITE messages. Normally, outgoing SIP INVITE messages contain the trunk group domain assigned to egress trunk group. `disable` (default) `enable` `useLowerCaseDomainNames` – Set flag to allow lower case domain names. `disable` (default) `enable`
`useZoneLevelDomainNameInContact`	Enable flag to use Zone level domain name in the Contact header. `disable` (default) `enable`
`useZoneLevelDomainNameInPathHdr`	Enable flag to send the Domain Name configured at the Zone level in the Path Header of the outgoing REGISTER message. `disable` (default) `enable`

Flags

Use this object to set egress IP attribute flags.

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes flags
	addLoopBackRouteHeader <disable | enable>
	bgcfTargetSchemeTransparency <disable | enable>
	convertInactiveToSendrecv <disable | enable> 
	disable2806Compliance <disable | enable> 
	disableOptionalRegisterParameters <disable | enable>
	ignoreSdpAfterOfferAnswerCompleted <disable | enable>
	includeEnumParameters <disable | enable>
	map3xxContactUrlToRouteHeader <disable | enable>
	map181Or182MessageTo183 <disable | enable> 
	mapContractorNumberInPSigInfoHeader <disable | enable>
	qosBasedRouting <disable | enable> 
	sameCallIdForRequiredAuthorization <disable | enable>
	suppressUnregister <disable | enable>
	transitPAIFromUnregisteredPeer <disable | enable>
	ttcIsupMapping <disable | enable> 
	useCalledPartyInRequestUri <disable | enable> 
	useColonInSdpMediaTypeParameter <disable | enable> 
	validateIsubAddress <disable | enable>

Command Parameters

Flags Parameters

Parameter	Description
`addLoopBackRouteHeader`	Enable flag to add the SBC URI as the second top-most Route header in the INVITE towards EATF. `disable` (default) `enable`
`bgcfTargetSchemeTransparency`	Enable flag to preserve the scheme used by the SIP INVITE Request-URI when the INVITE is routed by the Unable to show "metadata-from": No such page "_space_variables" , acting as a BGCF supporting Tel-URL. When disabled, the SBC changes the scheme used by the Request-URI parameter to SIP in the egress INVITE message. `disable` (default) `enable`
`convertInactiveToSendrecv`	Enable flag to control the a-line in the SDP of an egress SIP INVITE message by converting a=inactive to a=sendrecv. When disabled, the Unable to show "metadata-from": No such page "_space_variables" continues to use a=inactive, when appropriate, in the egress INVITE message. `disable` (default) `enable`
`disable2806Compliance`	If enabled, the 2806 Compliance Code is disabled and no phone context or user=phone parameters are signaled in egress messages. `disable` (default) `enable`
`disableOptionalRegisterParameters`	Enable flag to prevent Unable to show "metadata-from": No such page "_space_variables" from sending the DTG (Destination Trunk Group) parameter in the Contact header of egress REGISTER messages. `disable` (default) `enable`
`ignoreSdpAfterOfferAnswerCompleted`	Enable flag to allow the SBC to ignore the new SDP at the egress leg in subsequent 1xx-rel or final 200 OK messages after the Offer Answer for the initial Invite dialog was completed by an earlier 1xx-rel (and does not trigger a new offer or answer). `disable` (default) `enable`
`includeEnumParameters`	Use this flag to specify how to handle ENUM parameters in outgoing INVITE. `disabled` (default) – SBC drops ENUM parameters received from ENUM server. `enabled` – SBC sends ENUM parameters in the outgoing INVITE
`map3xxContactUrlToRouteHeader`	When map3xxContactUrlToRouteHeader flag is enabled, SBX adds 3XX contact header as second route header in the outgoing INVITE message. This flag is enabled on a IBCF TG because when a call is routed by ECSCF to IBCF, the 3xx contact URI need to be added as second route header for subsequent routing to IP-PSAP. `disable` (default) `enable`
`map181Or182MessageTo183`	Enable flag to allow Unable to show "metadata-from": No such page "_space_variables" to map 181 or 182 response messages to 183. When disabled, the SBC handles 1xx response messages normally. `disable` (default) `enable`
`mapContractorNumberInPSigInfoHeader`	Enable flag to map the Contractor Number parameter into the outgoing SIP P-Sig-Info header. The P-Sig-Info header is a customer-specific SIP header used to convey ISUP information in SIP messages. `disable` (default) `enable`
`qosBasedRouting`	Enable flag to allow QoS-based routing. `disable` (default) `enable`
`sameCallIdForRequiredAuthorization???`	Enable this flag to support sending an INVITE with credentials on receiving a 401 (Unauthorized) or 407 (Proxy Authentication Required) response to initial INVITE with the same call ID as in the original INVITE. `disable` (default) `enable`
`suppressUnregister`	Enable flag to prevent Unable to show "metadata-from": No such page "_space_variables" from sending an unregister message (Register=0) to the registrar upon expiration of a SIP UA registration. When disabled, the Unable to show "metadata-from": No such page "_space_variables" generates unregister messages on the egress leg if the UA does not refresh the registration on time. `disable` (default) `enable`
`transitPAIFromUnregisteredPeer`	Enable flag to transparently pass the received PAI to the INVITE if the default PUI procedure cannot add a PAI header. `disable` (default) `enable` To use this flag, you must enable the `enableDefaultPUIProcedures` flag and disable the `privacy transparency` flag.
`ttcIsupMapping`	When enabled, and when the IP protocol type of the IP signaling profile entry is SIP or SIP-I, the application that receives the Unable to show "metadata-from": No such page "_space_variables" policy response (which can be either the SIP signaling gateway application on the Unable to show "metadata-from": No such page "_space_variables" or the SIP core proxy on the Unable to show "metadata-from": No such page "_space_variables" ) applies the mapping necessary for TTC-ISUP signaling. `disable` (default) `enable`
`useCalledPartyInRequestUri`	When enabled, the Unable to show "metadata-from": No such page "_space_variables" copies the username selected for the "To" header to the Request URI instead of the registered username. When disabled, the Unable to show "metadata-from": No such page "_space_variables" includes the registered username in the Request URI. This flag is used when interoperating with IP-PBXs that require the real end station number in the Request URI in order to do proper routing of calls terminating on them. `disable` (default) `enable`
`useColonInSdpMediaTypeParameter`	When enabled, a colon (:) is used as the separator between the SDP Media Type parameter key and value. When disabled, an equal sign (=) is used as the separator between the SDP Media Type parameter key and value. `disable` (default) `enable`
`validateIsubAddress`	When enabled, the Unable to show "metadata-from": No such page "_space_variables" validates ISUB digits for called and calling parties. When isabled, the Unable to show "metadata-from": No such page "_space_variables" will not validate ISUB digits.

ISUB

Use this object to configure ISDN Calling Party Subaddress (ISUB) parameters:

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes isub 
	allowNsapIsub <disable | enable> 
	allowUserSpecifiedIsub <disable | enable> 
	includeCalledPartyIsub <disable | enable> 
	includeCallingPartyIsub <disable | enable>

Command Parameters

ISUB Parameters

Parameter	Description
`allowNsapIsub`	Enable to allow NSAP ISUB parameter. `disable` (default) `enable`
`allowUserSpecifiedIsub`	Allow user-specified ISUB. `disable` (default) `enable`
`includeCalledPartyIsub`	Include called party ISUB. `disable` (default) `enable`
`includeCallingPartyIsub`	Include calling party ISUB. `disable` (default) `enable`

Media QOS KPI Profile

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes mediaQosKpiProfile <profile_name>

Command Parameter

Media QOS KPI Profile Parameter

Parameter	Description
`mediaQosKpiProfile`	The Media QoS KPI (Key Performance Indicator) Profile name.

Number Globalization Profile

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes numberGlobalizationProfile <profile_name>

Command Parameters

Number Globalization Profile Parameter

Parameter	Description
`numberGlobalizationProfile`	The Number Globalize Profile name. This profile converts numbers to SIP global number format.

Number Portability Attributes

Number portability attributes configuration.

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes numberPortabilityAttributes 
	disableRn <disable | enable> 
	npdiOptions <doNotIncludeNpdi | includeNpdi | includeNpdiYes>

Command Parameters

Number Portability Attributes Parameters

Parameter Description

disableRn

Enable flag to prevent the

Unable to show "metadata-from": No such page "_space_variables"

and ERE SIP proxy/redirector from sending the SIP rn parameter in the egress INVITE message when an LNP translated number is present. When the flag is disabled, the

Unable to show "metadata-from": No such page "_space_variables"

and ERE SIP proxy/redirector send "rn=NNNN" in the userinfo portion of the Request URI, where "NNNN" is the LNP translated number.

disable (default)
enable

npdiOptions

Use the following options to specify whether the

Unable to show "metadata-from": No such page "_space_variables"

and ERE SIP proxy/redirector send the SIP NPDI parameter in the egress INVITE message when LNP translation is performed by ERE call processing or the preceding switch.

doNotIncludeNpdi – Do not send the NPDI parameter.
includeNpdi – Send "npdi" in the userinfo portion of the Request URI.
includeNpdiYes – (default) Send "npdi=yes" in the userinfo portion of the Request URI.

P-Charge Info

Use this parameter to configure egress P-Charge-Info header in INVITE message behavior.

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes pChargeInfo
	includeNOA <disable | enable>
	includeNPI <disable | enable>
	pChargeInfoTransparency <disable | enable>
	pChargeInfoType <headerParameter | uriParameter | userParameter>

Command Parameters

P-Charge Info Parameters

Parameter	Description
`includeNOA`	Enable flag to include Nature of Address Indicator in egress P-Charge-Info header in INVITE message. `disable` (default) `enable`
`includeNPI`	Enable flag to include Number Plan Indicator in egress P-Charge-Info header in INVITE message. `disable` `enable` (default)
`pChargeInfoTransparency`	Enable flag to transparently pass egress P-Charge-Info header in INVITE message. `disable` (default) `enable`
`pChargeInfoType`	The format types for which NPI/NOA are encoded in P-Charge-Info header. Options include: `headerParameter` – NPI and NOA are sent in header parameter format. For example, P-Charge-Info: <sip:123456@10.54.69.140>;npi=ISDN;noa=3 `uriParameter` (default) – NPI and NOA are sent in uri parameter format. For example, P-Charge-Info: sip:123456@10.54.69.144;npi=ISDN;noa=3 `userParameter` – NPI and NOA are sent in user info parameter format. For example, P-Charge-Info: <sip:12345;npi=ISDN;noa=3@10.54.69.144>

Phone Context Parameter Length

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes phoneContextParameterLength (0-31)

Command Parameter

Phone Context Parameter Length Parameters

Parameter Length/Range Description

phoneContextParameterLength

0-31

Use this attribute to specify the length of phone-context parameter sent in RURI and To headers of the egress message (default = 0).

When a value greater than "0" is configured, and the called number is globalized using the existing globalization profile, the PSX sends the configured value in a policy response to the

Unable to show "metadata-from": No such page "_space_variables"

. The

Unable to show "metadata-from": No such page "_space_variables"

uses this configured value to insert phone-context parameter of received length in RURI and To headers.

Privacy

Use this object to specify Privacy parameters.

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes privacy 
	flags 
		includeEmbeddedPAIheaderInRedirectedInvite <disable | enable> 
		includePrivacy <disable | enable> 
		msLyncPrivacySupport <disable | enable> 
		privacyRequiredByProxy <disable | enable> 
	privacyInformation 
			<pAssertedId | pPreferredId | remotePartyId> 
	transparency <disable | enable>

Command Parameters

Privacy Parameters

Parameter Description

flags

Privacy flags:

includeEmbeddedPaiHeaderInRedirectedInvite – Enable this flag to include the embedded PAI header in the redirected Invite message.
- disable (default)
- enable
includePrivacy – Use this flag to specify whether the SBC includes privacy information in outgoing SIP INVITE messages.
- disable – The
  Unable to show "metadata-from": No such page "_space_variables"
  does not include a P-Preferred-Identity header or a P-Asserted-Identity header, an Anonymous identifier in the SIP From field, or a Privacy header that contains a Critical token in outgoing SIP INVITE messages, and the
  Unable to show "metadata-from": No such page "_space_variables"
  will not include a P-Asserted-Identity header or a Privacy header that contains a Critical token in outgoing SIP INVITE messages.
- enable (default) – The
  Unable to show "metadata-from": No such page "_space_variables"
  includes either a P-Preferred- Identity header or a P-Asserted-Identity header (provisioned in Privacy Information above) in outgoing SIP INVITE messages. The
  Unable to show "metadata-from": No such page "_space_variables"
  will include a P-Asserted-Identity header in outgoing SIP INVITE messages. The
  Unable to show "metadata-from": No such page "_space_variables"
  will also insert an Anonymous identifier in the SIP From field and the
  Unable to show "metadata-from": No such page "_space_variables"
  will include a Privacy header that contains a Critical token.
msLyncPrivacySupport – Backward compatibility for the Caller Privacy feature. The Caller privacy feature only works if this flag is enabled.
- disable (default)
- enable
privacyRequiredByProxy – Enable flag to indicate that privacy service is mandated for any calls to the SIP trunk (proxy). In this case, the
Unable to show "metadata-from": No such page "_space_variables"
includes a Proxy-Require header with a privacy value, and a critical token in the Privacy header of the INVITE message. The privacy service must be applied by the proxy or the call is rejected. If disabled, the
Unable to show "metadata-from": No such page "_space_variables"
does not include a Proxy-Require header with privacy value. The proxy accepts the call even if it cannot provide privacy service.
- disable (default)
- enable

privacyInformation

Use this object to specify which of the following headers the

Unable to show "metadata-from": No such page "_space_variables"

uses when sending privacy information in outgoing SIP INVITE messages:

pAssertedId – Used among trusted SIP entities (typically intermediaries) to carry the identity of the caller as it was verified by authentication.
pPreferredId – Used by a User Agent (UA) to carry the identity the caller wishes to be used, and sent to a trusted proxy to be inserted in the P-Asserted-Identity field.
remotePartyId – Used among trusted SIP entities (typically intermediaries) to carry the identity of the caller as it was verified by authentication. This header is specified in an earlier RFC that continues to be supported.

transparency

Enable flag to allow ingress Privacy information to pass through unchanged.

disable (default)
enable

Redirect

Use this object to configure Redirect parameters.

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes redirect 
	contactHandling <mergeReceivedContacts | purgeExistingContacts> 
	flags 
		forceRequeryForRedirection <disable | enable>
		honorEmbeddedHeadersin3xx <disable | enable>
		relayUnusedContactParams <disable | enable>
		skipCrankbackProfileAndAlwaysCrankback <disable | enable> 
	mode <acceptRedirection | allowSingleRedirectAttempt | rejectRedirection>

Command Parameters

Redirect Parameters

Parameter Description

contactHandling

Select one of the following to control processing of contacts received in SIP Redirects:

mergeReceivedContacts – Contacts received in Redirects are ordered by q-value and inserted at the head of the list of untried contacts.
purgeExistingContacts – Contacts received in Redirects are ordered by q-value and replace untried contacts.

flags

Redirect flags:

forceRequeryForRedirection – (applies to Invite requests only) Use flag to re-query ERE with contact information received in a 3xx response for redirection-type scenarios.
- disable (default)
- enable
honorEmbeddedHeadersin3xx – Enable flag to allow the processing of embedded headers in 3xx Contact headers for the trunk group that received the 3xx.
- disable (default)
- enable
relayUnusedContactParams – When enabled, Contact parameters received in 3xx responses that are not consumed/processed locally by the SBC (see NOTE below) can now be passed through to the R-URI of subsequent INVITE request.
- disable (default)
- enable
skipCrankbackProfileAndAlwaysCrankback – Enable this flag to force any 4xx–6xx SIP response code to cause crankback so the next potential contact or 3xx response is tried. If disabled, only the response codes specified in default SBC crankback profile cause the call to crank back.
- disable (default)
- enable

mode

Use this object to control SIP redirection:

acceptRedirection (default) – Multiple redirections are allowed.
allowSingleRedirectAttempt – Only a single Redirect is allowed per route. Additional Redirects cause crankback to be performed.
rejectRedirection – If a Redirect is received, crank back is performed.

NOTE

Parameters consumed/processed locally by the SBC and excluded from relayUnusedContactParams command include:

dtg
tgrp
trunk-context
cic
npdi
npi
rn
bgid
bgt
user
phone-context

Back to Top

Signaling QOS KPI Profile

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes signalingQosKpiProfile <profile_name>

Command Parameter

Signaling QOS KPI Profile Parameters

Parameter	Description
`signalingQosKpiProfile <profile name>`	The Signaling QoS KPI (Key Performance Indicator) Profile name.

SIP Cause Mapping

Command Syntax

% set profiles signaling ipSignalingProfile <IPSP name> egressIpAttributes sipCauseMapping 
	sipToInternalCauseMappingProfileName <sipToInternalProfile_Name>
	internalToSipCauseMappingProfileName <internalToSIPProfile_Name>

Command Parameters

SIP Cause Mapping Parameters

Parameter

Description

sipCauseMapping

Use this object in a SBC ERE configuration to create Internal-to-SIP and SIP-to-Internal SIP Cause Mapping Profile names for this IP Signaling Profile.

internalToSipCauseMappingProfileName– The name of the Internal-to-SIP cause mapping profile.
sipToInternalCauseMappingProfileName – The name of the SIP-to-Internal cause mapping profile.

To create a profile to map CPC and SIP, refer to CPC to SIP Cause Map Profile - CLI and SIP CPC Cause Code Mapping Profiles - CLI.

To associated these profiles with Ingress/Egress trunk groups, refer to sipTrunkGroup signaling - CLI.

For configuration examples and external PSX considerations, see Configuring SIP Cause Code Mapping.

Back to Top

SIP Headers and Parameters

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes sipHeadersAndParameters 
	callForwarding 
		dataMapping <diversion | none | pkHeader> 
		diversionHeaderTransparency <disable | enable> 
		diversionHistoryInfoInterworking <disable | enable>
		historyInformation 
			includeHistoryInformation <disable | enable>
				causeParameterInRFC4458 <disable | enable> 
				reasonWithCauseValueAsPerRFC4244 <disable | enable>
 	destinationTrunkGroupOptions <includeDtg | includeNone | includeTgrpWithDomainName | includeTgrpWithIpAddress>
	flags 
		endToEndAck <disable | enable>
		includeCic <disable | enable> 
		includeCpcInformation <disable | enable> 
		includeNpi <disable | enable> 
		includeOlip <disable | enable> 
		includePKAdn <disable | enable> 
		includePstnParameters <disable | enable> 
		includeQvalue <disable | enable> 	
		skipCSeqCheckInEarlyDialog <disable | enable> 
		transparencyForDestinationTrunkGroupParameter <disable | enable>
	generateCallIdUsing <doNotUseIngressCallId | useIngressCallIdByAddingStaticString | useIngressCallIdByPrepending>
	includeChargeInformation <includeNone | includePChargeInfo> 
	originatingTrunkGroupOptions <includeNone | includeOtg | includeTgrpWithDomainName | includeTgrpWithIpAddress> 
	sipToHeaderMapping <calledNumber | gapDialedNumber | none | originalCalledNumberOcn>

Command Parameters

sipHeadersAndParameters Parameters

Parameter	Description
`callForwarding`	This parameter is used to control the call forwarding data mapping method in egress SIP signaling. `dataMapping` – Use this parameter to define how to map the diversion or redirecting data. Options are: `none` – No Diversion information is egressed. `diversion` – Diversion information is sent out as SIP Diversion Header. `pkHeaders` – Diversion information is sent out as proprietary PK Headers. `diversionHeaderTransparency` – When enabled, the ingress Diversion header is passed through unchanged. Call forwarding data mapping transparency applies to Diversion header only `disable` (default) `enable` `diversionHistoryInfoInterworking` – Enable flag to allow interworking between Diversion and History-Info header as per RFC 6044. The Unable to show "metadata-from": No such page "_space_variables" supports up to 12 History-Info entries and 10 Diversion entries. When this flag is disabled, only the first and last entries are maintained when History-Info or diversion transparency is disabled. `disable` (default) `enable` `diversionHistoryInfoInterworking` is only visible when either Diversion or History-Info header is selected as the egress call forwarding header. Diversion and History-Info Transparency configuration controls are ignored when it is enabled. This parameter has precedence over the others. `historyInformation includeHistoryInformation` – Use this parameter to specify how to treat call forwarding history information. Enable this flag to include History-Info in INVITE egress message. `disable` (default) `enable` `causeParameterInRFC4458` – Enable this flag to include the History-Info cause value in egress message as per RFC 4458 recommendation. When the flag is enabled, the output is similar to the following example: `History-Info: <sip:1234567890@P1.interwork.com?Privacy=none>;index=1, <sip: last_diverting_target;cause=408>;index=1.1` `disable` (default) `enable` `reasonWithCauseValueAsPerRFC4244` – Enable this flag to include History-Info cause value with Reason Header as per RFC 4244 recommendation. When the flag is enabled, the output is similar to the following example: `History-Info: <sip:1234567890@P1.interwork.com?Privacy=none>;index=1, <sip: last_diverting_target?Reason=SIP%3Bcause%3D408>;index=1.1` `disable` (default) `enable`
`destinationTrunkGroupOptions`	Use this parameter to specify destination trunk group options. `includeDtg` – Include the destination trunk group parameter in SIP headers sent over associated trunk group. `includeNone` (default) – Do not include any trunk group information. `includeTgrpWithDomainName` – Include trunk group with domain name. `includeTgrpWithIpAddress` – Include the destination trunk group, and include the trunk context as domain name.
`flags`	Use this object to configure the SIP Headers and Parameters flags. `endToEndAck` – Enable flag to send the ACK towards egress for the initial invite after receiving it from the ingress (remote) entity. The application retransmits the 200 OK towards the ingress side based on the configuration, and terminates the call if no ACK is received for the corresponding 200 OK. `disable` (default) `enable` `includeCic` – If enabled, the Unable to show "metadata-from": No such page "_space_variables" includes the Carrier Identification Code in a cic= parameter in outgoing INVITE messages. `disable` (default) `enable` `includeCpcInformation` – If enabled, the Unable to show "metadata-from": No such page "_space_variables" includes the Calling Party Category (CPC) parameter value in the From header of outgoing SIP INVITE messages.The CPC parameter characterizes the station used to originate a call, such as ordinary, priority, data, test, operator, pay phone, prison, hotel or unknown. `disable` (default) `enable` `includeNpi` – If enabled, the Unable to show "metadata-from": No such page "_space_variables" includes the Numbering Plan Indicator in a npi= parameter in outgoing INVITE messages. `disable` (default) `enable` `includeOlip` – If enabled, the Unable to show "metadata-from": No such page "_space_variables" includes the Originating Line Information Parameter in a oli= parameter in outgoing INVITE messages. `disable` (default) `enable` `includePKAdn` – When enabled, the Unable to show "metadata-from": No such page "_space_variables" includes the P-K-Adn header in egress SIP messages. When disabled, the Unable to show "metadata-from": No such page "_space_variables" does not include the P-K-Adn header. The P-K-Adn header is a customer-specific SIP header used for ISUP-to-SIP interworking and contains the Translation Source Number (TSN) used in Number to SIP URL translation via the Number Username Translation screen (Generic variant only). `disable` (default) `enable` `includePstnParameters` – If enabled, the Unable to show "metadata-from": No such page "_space_variables" includes a set of specific PSTN parameters in a pstn-params= entry in outgoing INVITE messages. The PSTN parameters currently included in pstn-params are Screening Indicator, ISDN Indicator, and Transmission Medium Requirement (TMR). `disable` (default) `enable` `includeQvalue` – If enabled, the ERE SIP proxy/redirector includes the qvalue parameter (for example, q=0.9) in the Contact header of outgoing 3xx messages. `disable` (default) `enable` `skipCSeqCheckInEarlyDialog` – When enabled, the Unable to show "metadata-from": No such page "_space_variables" accepts multiple SIP requests in which the CSeq number in a later request is of a lesser value than the CSeq number received in earlier requests. `disable` (default) `enable` `transparencyForDestinationTrunkGroupParameter` – When enabled, if ERE receives both tgrp parameter and trunk-context in an ingress INVITE Request-URI, ERE as proxy transparently passes the tgrp parameter and trunk-context in the egress INVITE Request-URI. Values selected for the "Destination Trunk Group Option" are ignored. `disable` (default) `enable`
`generateCallIdUsing`	Use this parameter to control ingress and egress Call-ID behavior. `doNotUseIngressCallId` – Generates egress Call-ID independent of ingress Call-ID. `useIngressCallIdByAddingStaticString` – Generates egress Call-ID using ingress Call-ID and a static string (`egressCallIdStaticString`) configured in the SIP trunk group. Egress Call-ID is the aggregate of ingress Call-ID and static string. `useIngressCallIdByPrepending` – Generates egress Call-ID using ingress Call-ID and locally generated string. Egress Call-ID is the aggregate of ingress Call-ID and locally generated string.
`includeChargeInformation`	Select the `includePChargeInfo` option to map charge information in a call setup message (i.e., the charge number parameter of an IAM) to egress P-Charge-Info header in INVITE message. If the ERE returns billing information in a policy response, the Unable to show "metadata-from": No such page "_space_variables" ensures that the egress P-Charge-Info header in INVITE message is populated with the indicated data. If the Unable to show "metadata-from": No such page "_space_variables" receives a SIP INVITE message for a call destined to the PSTN, the Unable to show "metadata-from": No such page "_space_variables" populates the charge number parameter of the outgoing IAM based on the egress P-Charge-Info header in INVITE message. `includeNone` (default) `includePChargeInfo`
`originatingTrunkGroupOptions`	Use this parameter to specify originating trunk group options. `includeNone` (default) – Do not include any trunk group information. `includeOtg` – Include the originating trunk group parameter in SIP headers sent over the associated trunk group. `includeTgrpWithDomainName` – Include the originating trunk group, and include the trunk context as domain name. `includeTgrpWithIpAddress` – Include the originating trunk group, and include the trunk context as IP address
`sipToHeaderMapping`	This parameter indicates which number is mapped and returned in the outgoing SIP To header. Options include: `calledNumber` – The TO header is mapped using the called number. `gapDialedNumber` – The TO header is mapped using the Generic Address Parameter from mime, if applicable. `none` (default) – The TO header user part is mapped from the Original Called Number, if present. Otherwise, it is mapped from the Called Number. The Original Called Number may be taken from the Diversion or the History-Info header, if present, in a SIP Invite. `originalCalledNumberOcn` – The TO header is mapped using the redirecting original Called number OCN parameter. This is filled from the SIP Invite using the Diversion or the History-Info header, if present.

Back to Top

Transport

Command Syntax

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes transport type1...type4 
	none
	sctp
	tcp
	tlsOverTcp
	udp

Command Parameters

Transport Parameters

Parameter

Length/Range

Description

transport

N/A

Use this object to set up to four transport parameter types:

type1
type2
type3
type4

Each transport type above can be set to any one of the following transport protocols:

none (default)
sctp
tcp
tlsOverTcp
udp

Back to Top

Space shortcuts

Page tree

egressIpAttributes - SIP - CLI

BCI

Command Syntax

Command Parameters

Domain Name

Command Syntax

Command Parameters

Flags

Command Syntax

Command Parameters

ISUB

Command Syntax

Command Parameters

Media QOS KPI Profile

Command Syntax

Command Parameter

Number Globalization Profile

Command Syntax

Command Parameters

Number Portability Attributes

Command Syntax

Command Parameters

P-Charge Info

Command Syntax

Command Parameters

Phone Context Parameter Length

Command Syntax

Command Parameter

Privacy

Command Syntax

Command Parameters

Redirect

Command Syntax

Command Parameters

Signaling QOS KPI Profile

Command Syntax

Command Parameter

SIP Cause Mapping

Command Parameters

SIP Headers and Parameters

Command Syntax

Command Parameters

Transport

Command Syntax

Command Parameters