sipTrunkGroup services - CLI

In this section:

Use this object to specify parameters associated with various enhanced services and features for this SIP trunk group.

CLI commands are case-sensitive and must be entered exactly as shown in this guide. Objects and profiles with names that differ only in case are considered distinct objects.

For example, the following trunk groups are three distinct trunk group entities: trunkgroup1, TRUNKGROUP1, TrunkGroup1. It is strongly recommended to avoid such naming conventions, and to also adopt a standard naming convention when initially defining your configuration.

As a best practice, always use UPPERCASE for trunk group names.

Command Syntax

% set addressContext <name> zone <name> sipTrunkGroup <name> services
	colocatedPandEcscf <disabled | enabled>
	dialogEventNotificationSupported <disabled | enabled>
	disconnectTreatmentProfile <h323Default | sipDefault>
    dnsSupportType <a-only | a-srv-naptr>
    dynamicBlacklistProfile <profile name>
    emergencyCallHandlingMode <emergencyRegRequired | emergencyRegSupported | none | rejectWith380>
    emergencyCallProfile <profile name>
    honorSdpClockRate <disabled | enabled> 
    jsrcBandwidthReservation <disabled | enabled>
    longDurationCall 
        action <noAction | release | trap | trapAndRelease> 
        emergencyCalls <exclude | include> 
        relCause <#> 
        timeoutValue <0-44640 minutes>
    natTraversal 
        adaptiveLearning
            maxTcpPinholeTimer <60-65535>
            maxUdpPinholeTimer <60-65535>
            reLearningInterval <1-240>
            state <disabled | enabled> 
		iceSourceAddressFilterPriority
			serverReflexivePrefixLength <unsignedInt | 0..32>
        	state <disabled | enabled>
		iceSupport <none | iceWebrtc | iceLync | iceFull>
        learnNatForRtpOnly <disabled | enabled>
        mediaNat <disabled | enabled> 
        outboundTcpKeepaliveTimer <0-32767> 
        outboundUdpKeepaliveTimer <0-32767>
        qualifiedPrefix <IPv4 address> 
        secureMediaNatPrefix <0-32>
        signalingNat <disabled | enabled>
        tcpKeepaliveTimer <15-65535> 
        udpKeepaliveTimer <15-65535>
    overlapAddressing 
        minDigitsForQuery <#> 
        overlapState <disabled | enabled> 
        receive <InfoMethod | MultiInvite | disabled> 
        send <InfoMethod | MultiInvite | disabled> 
        timer1 <integer> 
        timer2 <integer> 
        timer3 <integer>
    preconditionIntwkUsing183 <disabled | enabled>
    preconditions <none | required | supported | transparent>
    remoteEPreservation <disabled | enabled>
    resolvedDnsPrioritization <alwaysPrioritize | doNotPrioritize>
	sipArsProfile <profile name>
    sipJipProfile defaultJipProfile
    sipJurisdictionSupport <disabled | enabled>
    sipSecurityProfile <profile name>
    transmitPreconditions <none | required | supported>
    transparencyProfile <Transparency Profile name>

Command Parameters

SIP Trunk Group Services Parameters

SIP Trunk Group Services Parameters

Parameter	Description
`colocatedPandEcscf`	Use this flag to support notification for a SUBSCRIBE with dialog event in this Trunk Group. `disabled` (default) `enabled`
`dialogEventNotificationSupported`	Use this flag to support co-locating P-CSCF and E-CSCF on the ingress Trunk Group. `disabled` (default) `enabled`
`disconnectTreatmentProfile`	Disconnect Treatment Profile name.
`dnsSupportType`	Indicates whether to use the DNS server for just A-record lookups, or for full NAPTR/SRV/A lookup as specified in RFC3263. `a-only` `a-srv-naptr`
`dynamicBlacklistProfile`	Dynamic Blacklist Profile name.
`emergencyCallHandlingMode`	Use this parameter to specify how to handle emergency calls. `emergencyRegRequired` – Use this option to reject the emergency session establishment without an emergency registration. “`usePsxRouteForEmergencyCall`” must also be enabled to use this option. `emergencyRegSupported` – Use this option when emergency registrations are supported, but emergency session establishment is possible without an emergency registration. “`usePsxRouteForEmergencyCall`” must also be enabled to use this option. `none` (default) – Use this option when not using emergency registrations to perform PSX dip for registered user for emergency calls. “`usePsxRouteForEmergencyCall`” must also be enabled to use this option. `rejectWith380` – Use this option to reject an INVITE request with ‘380 Alternate Service’ response code from Ingress leg when the request is identified as emergency request and redirection flag is set to redirection mode. See Emergency Registration for emergency registration functionality.
`emergencyCallProfile`	Emergency Call Profile name.
`honorSdpClockRate`	Enable this flag to allow the mapping of up to five DTMF Payload Types (PT), each with a different clock rate of a preferred or selected payload type for audio. If the flag is disabled, all DTMF PTs except 8 kHz (both send and receive) are dropped. `disabled` (default) `enabled`
`jsrcBandwidthReservation`	Enable flag to require bandwidth reservation with Juniper Session Resource Controller. `disabled` (default) `enabled`
`longDurationCall`	The parameters associated with long duration call supervision. `action` – This is the action to take if the long duration call timer expires. `noAction` (default) `release` `trap` `trapAndRelease` `emergencyCalls` – Specifies whether Emergency Calls should be excluded from or included in Long Duration Call Disconnect procedures. `exclude` (default) `include` `relCause` – The Q.850 release value to use should the call be released due to long duration call timer expiry. (default = 41). `timeoutValue` – Timeout value (in minutes) of the long duration call timer. 0 (default) – Disable the timeout. 1-44640 – Set the timeout to the specified value.
`natTraversal`	Specifies the various parameters associated with network-hosted NAT/NAPT traversal for SIP endpoints. Specify the following NAT Traversal parameters. See NAT Traversal Parameters table below for parameter details.
`overlapAddressing`	Parameters associated with overlap addressing support. `minDigitsForQuery` – Minimum number of digits that need to be received before attempting to route the call. (range: 0-30 / default = 0). `overlapState` – Specifies the whether to support or not support overlap addressing. `disabled` (default) `enabled` `receive` – Use this parameter to specify the Incoming overlap type. `InfoMethod` – Select to support Info-based overlap dialing where initial INVITE with incomplete called party digits is answered locally by the SBC to establish early dialog, and subsequent digits are received through INFO message to complete dial sequence. `MultiInvite` – Select to process multiple INVITEs for the same call with additional digits to complete the dial sequence. `disabled` (default) – Select to disable this feature. `send` – Use this parameter to specify the Outgoing overlap type. `InfoMethod` – Select to support Info-based overlap dialing where initial INVITE with incomplete called party digits is answered locally by the SBC to establish early dialog, and subsequent digits are received through INFO message to complete dial sequence. `MultiInvite` – Select to process multiple INVITEs for the same call with additional digits to complete the dial sequence. `disabled` (default) – Select to disable this feature. `timer1` – Specifies the maximum time (in seconds) between collection of digits. (range: 5-15 / default = 10) `timer2` – Maximum time (in seconds) between sending an INVITE and receiving a backward message. (range: 0-14 / default = 0). `timer3` – Maximum time (in seconds) between receiving a 484 Address Incomplete message (if there are no outstanding INVITE transactions) and the receipt of fresh address information. (range: 4-64 / default = 4).
`preconditionIntwkUsing183`	(This flag is for specific call flows and is not intended for generic use) Enable this flag to locally generate first 183 responses for preconditions interworking before egressing INVITE. If disabled, these responses are dropped. `disabled` (default) `enabled` Do not enable `preConditionIntwkUsing183` when End-to-End Prack is configured.
`preconditions`	Use this parameter to level of preconditions support for incoming (only) requests. `none` – (default) `required` `supported` `transparent` – Select this option to allow SBC to pass the received precondition option tag (either in require or supported) and precondition attributes present in SDP transparently. The `transparent` option must be configured on both Egress and Ingress legs. For precondition support of outgoing requests, see `transmitPreconditions` flag below.
`remoteEPreservation`	Enable flag to require bandwidth reservation with the Juniper Session Resource Controller for the remote endpoint. `disabled` (default) `enabled`
`resolvedDnsPrioritization`	Use this parameter to control DNS prioritization for the specified SIP trunk group. `alwaysPrioritize` – The SBC sends the requests in a dialog to the IP address where the INVITE was sent and the contact in the response message is an FQDN that resolves into multiple IP addresses. `doNotPrioritize` – (default) The SBC latches on the first resolved IP address.
`sipArsProfile`	The name of the SIP ARS (Address Reachability Service) profile.
`sipJipProfile`	`defaultJipProfile` – The default name of the SIP JIP profile to associate in egress and ingress SIP Trunk Groups. This parameter is only supported when the SBC is configured to use an external PSX.
`sipJurisdictionSupport`	Enable this flag to allow insertion of JIP parameter in SIP trunk group ingress and egress headers. `disabled` (default) `enabled` This flag is only supported when the SBC is configured to use an external PSX.
`sipSecurityProfile`	The name of the SIP Security Profile.
`transmitPreconditions`	Indicates level of preconditions support for outgoing request/response. `none` – When set to "none", Unable to show "metadata-from": No such page "_space_variables" does not add SIP precondition attributes in SDP of outgoing request even if attributes are present in the SDP of incoming requests. `required` – Use this option to add SIP precondition attributes in SDP of outgoing request even if attributes are NOT present in the SDP of incoming requests. If precondition attributes are added by Unable to show "metadata-from": No such page "_space_variables" , the local preconditions are set to ‘met’ and remote preconditions are set to ‘not-met’. `supported` – (default) Use this option to ensure backward compatibility behavior. Use this option to add SIP precondition attributes in SDP of outgoing request only if attributes are present in the incoming request.
`transparencyProfile`	The name of the Transparency Profile to associate with this SIP Trunk Group.

NAT Traversal Parameters

Parameters		Description
`adaptiveLearning`	N/A	Adaptive NAT pinhole learning parameters. `maxTcpPinholeTimer` – Defines upper limit of the pinhole timeout for TCP in seconds. (range: 60-65535 / default = 600). `maxUdpPinholeTimer` – Defines the upper limit of the pinhole timeout for UDP in seconds. (range: 60-65535 / default = 180). `reLearningInterval` – Interval in hours at which the pinhole timeout is relearned. (range: 1-240 / default = 24). `state`– Enables/disables the adaptive nat pinhole timeout learning process for devices behind NAT. `disabled` (default) `enabled`
`iceSourceAddressFilterPriority`	N/A	Enable this parameter for the SBC to prioritize the processing of STUN packets matching the source addresses received in the candidate lines of the ICE SDP received from the peer during the STUN connectivity check phase. `serverReflexivePrefixLength` – The length (in bits) of the prefix for server reflexive IP address (range: 0-32 / default = 16). `state` – Administrative state of `iceSourceAddressFilterPriority`. `disabled` `enabled` (default) The filtering mechanism is applicable to the following RTP address types: IPV4 Server Reflexive Address (for this address type, filtering is based on the provisioned Server Reflexive Prefix Length) IPV4 Relay Address IPV6 Relay Address IPv6 Host Address NOTE: When ICE Source Address Filtering is enabled, STUN packets received during the connectivity check phase that do not match the addresses sent by the peer are still processed, but at a reduced rate. This allows the SBC to learn of the presence of Peer Reflexive Candidates through STUN. This has no impact during a stable call when only packets received from the learned source address are processed and the remaining are dropped by default.
`iceSupport`	N/A	This parameter indicates the type of ICE method used for STUN packet check. `none` (default) `iceWebrtc` – Use this attribute for WebRTC Gateway interworking. For example, using the Sonus WRTC Gateway, or in situations when the SBC is presented with an ICE SDP from a WebRTC-enabled Endpoint. When configured for this mode, SBC acts as a generic ICE-Lite agent. `iceLync` – Use this attribute when interworking with a Microsoft Lync 2010 or 2013 client. `iceFull` – Use this attribute when interworking with a full ICE client requiring the generation of a STUN connectivity check by the SBC in response to its own STUN connectivity check. The "`iceFull`" implementation is for lab use only in 5.0.0 release. NOTE: Sonus recommends to avoid configuring both Media Nat and ICE Support on the same Trunk Group because these configurations are independent mechanisms for solving NAT traversal issues. Because of of this, these configurations should not coexist on the same Trunk Group. See ICE-Lite Support for feature details. See Configuring SBC for WRTC for ICE-Lite configuration best practices.
`learnNatForRtpOnly`	N/A	Enable flag to learn media NAT from the first RTP packet only. If disabled, media NAT is learned from any first packet received. For egress trunk groups, this flag is applicable only if `dynamicLRBT` flag is disabled. If `dynamicLRBT` is enabled, NAPT learning occurs on arrival of RTP packet until the call is connected, at which point `learnNatForRtpOnly` applies even for egress Trunk Groups. disabled (default) enabled The flag `mediaNat` must be enabled to use this flag. Do not enable `learnNatForRtpOnly` for SIP trunk groups with `iceSupport` enabled because it does not apply to ICE NAT traversal.
`mediaNat`		Specifies the whether or not NAT/NAPT support is required for media. `disabled` (default) `enabled` NOTE: Sonus recommends to avoid configuring both Media Nat and ICE Support on the same Trunk Group because these configurations are independent mechanisms for solving NAT traversal issues. Because of of this, these configurations should not coexist on the same Trunk Group.
`outboundTcpKeepaliveTimer`	0-32767	The NAT outbound keep-alive timer (in seconds) for SIP over TCP (default = 240)
`outboundUdpKeepaliveTimer`	0-32767	The NAT outbound keepalive timer (in seconds) for SIP over UDP (default = 60)
`qualdifiedPrefix`	N/A	Set of IP network media and signaling prefixes that an address must match to be considered for NAT handling. If there are no entries in `qualifiedPrefix`table, the endpoint is treated as existing behind a NAT device. As a result, SBC considers requests from all IP addresses to be behind a NAT device. `ipAddress` – IPv4 or IPv6 address. `prefixLength` – Value from 0-128 specifying the number of bits representing the network part of `ipAddress`.
`secureMediaNatPrefix`	0-32	Use this parameter to match up to 'N' bits of the network IPv4 address obtained from signaling. If set to "0", feature is disabled, and no match of network IP address will occur. (default = 0)
`signalingNat`	N/A	This indicates whether or not NAT/NAPT support is required for signaling. `disabled` (default) `enabled`
`tcpKeepaliveTimer`	15-65535	This NAT TCP keep-alive timer sets the registration refresh rate (in seconds) for SIP over TCP. (default = 240).
`udpKeepaliveTimer`	15-65535	This NAT UDP keep-alive timer sets the registration refresh rate (in seconds) for SIP over UDP. (default = 60).

Space shortcuts

Page tree

Command Syntax

Command Parameters

SIP Trunk Group Services Parameters

NAT Traversal Parameters