DO NOT SHARE THESE DOCS WITH CUSTOMERS!
This is an LA release that will only be provided to a select number of PLM-sanctioned customers (PDFs only). Contact PLM for details.
Network-wide licensing using a site license server (SLS) has been discontinued and is no longer available on SBC 8.0 or later releases.
Note
In this section:
| Common Call Statistics Terminology | |
|---|---|
| Stable Calls | Calls that are established and fully stable (connected and media cut-through type of calls) and will survive a fail-over. This excludes calls in establishing, clearing and updating states which will not survive a fail-over. |
| Active Calls | A snapshot of total number of active calls on the SBC at the point of execution of the status command. This count reflects the actual live calls on the box independent of the state of the call (setup, stable, updating or clearing). |
| Call Attempts | Accumulative number of attempted calls on this system since the last reboot/start-up, including calls where a setup was sent/received, uncompleted calls (calls failed, busy, not answered, etc.) and calls completed (answered). |
| Call Completions | Accumulative number of calls completed on this system since the last reboot/start-up. |
The SBC allows the operator to access data from the current interval and from the interval statistics table related to each object being monitored. The current interval consists of a statistics table entry that is accumulating data for the next interval report. The interval statistics table is a series of statistics table entries containing data from the most recently completed n intervals (where n is the number of intervals in the retention policy configuration).
Note
Refer to Links to Statistics Pages to navigate to a particular EMA or CLI statistics page.
System
Command Syntax
Below is a high-level view of the command syntax for 'show status system' command.
> show status system
activeFileConfig
activeRevision
admin
announcements
adSyncStatus
baseMacAddress
configMode
coredumpList
coredumpSummary
cpuUtilCurrentStatistics
cpuUtilIntervalStatistics
databaseIntegrity
daughterBoardStatus
dodModeStatus
dsbc
dspRes
dspStatus
ethernetPort
fanStatus
fileStatisticsStatus
fipsFSMState
haConfig
hardDiskStatus
hardDiskUsage
highAvailabilityPort
ipPolicing
isOAM
jsrcServer
ledStatus
licenseDomainBundleInfo
licenseInfo
licenseNodeLockedBundleInfo
licenseStatus
loadBalancingService
logicalMgmtIpInterfaceStatus
macAddressStatus
mediaProfile
memoryUtilCurrentStatistics
memoryUtilIntervalStatistics
metaVariable
mgmtIpInterfaceGroup
networkProcessorStatistics
niceLicense
ntp
objectStoreParameters
pdcsLicense
policyServer
powerSupplyStatus
savedConfigList
sbcliLicense
sbcPersonalityStatus
security
serverAdmin
serverSoftwareUpgradeStatus
serverStatus
softwareUpgradeDetailedStatus
softwareUpgradeStatus
standbySyncStatus
syncStatus
systemCongestionCurrentStatistics
systemCongestionIntervalStatistics
systemCongestionStatus
Command Parameters
Note
The following objects are included in this table for completeness, but only apply when using the
command:clusterAdmin, congestion, daughterBoardAdmin, dspPad, fileStatisticsAdmin, fipsBypassMode, intervalStatistics, licenseRequired, logicalMgmtIpInterface, media, metaVariableDynamic, mgmtStaticRoute, pathCheckPath
Shared Common Parameters - 'show status system' and 'show table system'
Parameter | Description |
|---|---|
activeConfigFile | Displays the file name of the last retrieved file from the external object store service. |
activeRevision | Numeric identifier for the active configuration revision level. (SBC SWe N:1 HA deployments only) The revision number is incremented when executing the CAUTION: In certain scenarios, a managed node is unable to apply changes due to unexpected configuration conflicts or network error conditions. Such situations trigger a sonusSbxManagedNodeUnableToReceiveConfigUpdates alarm and set the |
| Basic configuration (name, location, etc) for the system. See Admin Attributes table below for details. |
| Announcement file status and statistics. See Announcements Attributes table below for details. |
| Displays base MAC address of servers.
|
bfdSessionStats | Displays the status of the active BFD sessions.
|
clusterAdmin | Displays cluster-specific configuration details.
|
configMode | Indicates the configuration mode for the node.
|
| System congestion profile for the node.
|
| List of core dumps on the server(s). Fields include:
|
| Summary of core dump files on server(s).
|
cpuTranscodeStatus | Available only on SWe except S-SBC SWe. See CPU Transcode Status for details. |
| The CPU utilization of the server for the current period.
|
| The CPU utilization for the 'n' number of intervals.
|
databaseIntegrity | Displays SBC database sync status from executing the The following command options are available to match the results of the 'show' command with the associated 'request' command: activeAndStandbyPolicy – Display results of the sync check against policy databases on the active and standby servers. Displayed results include the following fields:
|
| SBC 5x10/7000 daughter board administrative status from server/CE level.
NOTE: Not applicable for 5x00 or SWe systems. |
| Server Daughter Board (DB) status details. See Daughter Board Status Attributes table below for details. |
dodModeStatus | DoD mode status details, with following details:
|
dsbc | Distributed SBC (D-SBC) statistics details.
|
| DSP PAD configuration service (must be restarted for new configuration to take effect). See DSP PAD Attributes table for details (for 'show table system' command only). |
| DSP historical interval statistics. See DSP Resources Attributes table below for parameter details.
|
| Status of DSP resources. See DSP Status Attributes table below for details. |
ems | EMS-specific configuration.
Applies to SBC SWe systems only. |
| Configuration for management, packet, and field service Ethernet ports. See Ethernet Port Attributes table for details. |
| Fan status on the server(s).
|
fileStatisticsAdmin | Displays whether the following interval statistics are enabled/disabled to write data to the statistics file.
|
| Displays the current ID of the last performance statistics data written to the database. |
fipsFSMState | FIPS finite state machine state.
|
gpuStatus | SWE only. Returns server name and GPU number for each attached GPU. See GPU Status table for details. |
gpuTranscodeStatus | Returns GPU codec channel capacities. Available only on SBC SWe except S-SBC SWe. See GPU Transcode Status for details. |
haConfig | This statistic displays GRHA status details.
|
| Hard disk status on the server(s).
|
| Hard disk usage on the server(s).
NOTE: The role of the standby server is reflected as Primary for the root partition because the other partition, /var/log/sonus/sbx/evlog is not mirrored/mounted in the standby CE until a switch-over occurs and the Standby assumes the role of active. |
| Configuration and status for the HA ethernet ports.
|
| The system- wide settings for interval statistics.
|
| The MIB Module for IP Monitoring statistics. These statistics are divided into three categories: Offenders List/Offenders Interval statistics, Micro Flow statistics and System statistics. Some or all of the following fields appear in the Offenders List/Offenders Int Stats statistics, depending on the type:
Offenders Lists: (See Offenders Lists for additional details about each type of list)
Offenders Interval Statistics:
Micro Flow statistics:
NOTE: This command displays any micro flow entry regardless of whether SIPFE or MRM (or any sub-system) created the micro flow. System statistics:
|
isOAM | Indicates whether the node is an OAM node.
|
| JSRC server configuration.
|
| Displays status of various LEDs of the server.
|
licenseDomainBundleInfo | License details for the domain licenses available on the SBC. See License Attributes table for details. |
| The license status for registered license features. See License Attributes table for details. |
licenseNodeLockedBundleInfo | License details for the node-locked licenses stored on the SBC. See License Attributes table for details. |
licenseRequired | Displays the (Applies to 'show table' command only) |
| The CE license status table describes the current CE license state, for example " |
| The Load Balancing Service status/statistics details with the following fields. See one of the following tables, as applicable, for details: |
| The logical management IP interface status/statistics details with following fields:
|
| The Logical Mgmt IP Interface status status/statistics details with following fields:
|
macAddressStatus | Displays MAC addresses of the system server(s).
|
| System- wide media configurations, UDP port range and RTP/RTCP peer inactivity timeout.
|
| DSP Media Profile configuration. (The System Media Profile configuration applies to hardware platforms (5000 series, 5400, 7000) only.)
|
| The memory utilization for the current interval period. Fields include:
|
| The memory utilization for the 'n' number of intervals.
|
metaVariable | Displays the system dynamic metavariable names and values.
|
metaVariableDynamic | Displays user-configured metavariables that add to the metadata available to an existing SBC SWe N:1 HA or cloud-based deployment.
|
| A group of management IP interfaces for the default address context. See Mgmt IP Interface Group Parameters table below for details. |
| Static IP routes for this address context.
|
networkProcessorStatistics | NOTE: For internal debug use only. Network Processor statistics details.See Network Processor Attributes table below for details. |
niceLicense | Reports whether the SBC NICE recording feature is dependent on the setting for the feature within the SBC's license. For deployments that upgraded and were already using the legacy license model, this status is set to "true" automatically and access to the NICE recording feature is maintained without the need to install a new license. If the status is set to "false" your installed license must have NICE recording explicitly enabled to enable the feature. |
| NTP services management details. See NTP Attributes table below for details. |
objectStoreParameters | Parameters used to specify an object store service to upload or download a configuration file ( SBC SWe cloud-based deployments only) |
pathCheckPath | Path for ICMP ping mechanism
NOTE: This field applies to the 'show table' command only. |
pdcsLicense | Reports whether the SBC feature which enables lawful call interception based on receipt of a SIP P-DCS-LAES header is dependent on the setting for the feature within the SBC's license. For deployments that upgraded and were already using the legacy license model, this status is set to "true" automatically and access to the P-DCS-LAES feature is maintained without the need to install a new license. If the status is set to "false" your installed license must have the P-DCS-LAES feature explicitly enabled to enable the feature. |
| Softswitch servers and client services status/statistics details. See Policy Server Attributes table below for details. |
| Power consumption/state of the server.
|
rgStatus | Displays the status of the instances in a redundancy group. NOTE: This command applies to N:1 redundancy configurations only. |
| List of configurations saved on the system.
|
sbcliLicense | Reports whether the SBC feature which enables lawful interception (LI) service using ERE is dependent on the setting for the feature within the SBC's license. For deployments that upgraded and were already using the legacy license model, this status is set to "true" automatically and access to the feature is maintained without the need to install a new license. If the status is set to "false" your installed license must have the LI feature explicitly enabled to enable the feature. |
sbcPersonalityStatus | Displays the personality role of the SBC SWe instance. Choices are isbc, msbc and ssbc. |
| Security management status/statistics details. See Security Attributes table for details. |
| The serverAdmin table describes the configuration of each server module.
|
| The system server software upgrade status table describes the status of the server software upgrade module.
|
| The system server status table provides status of the server module.
|
serviceDiscovery | The settings for the Service Registry and name server used to resolve FQDNs as part of Service Discovery. Refer to Service Discovery for Trap Target Destinations and EMS Registration.
|
slb | SIP-aware front-end Load-Balancer (SLB) configuration. See SLB for details. |
softwareUpgradeDetailedStatus |
|
| LSWU status at any given time with the following details.
|
standbySyncStatus | Sync status details of the standby node for active nodes created through a N:1 redundancy group configuration.
|
| HA Redundancy: Sync status of both the active and standby nodes for an SBC HA pair.
N:1 Redundancy: Sync status of both the active and standby nodes created through a N:1 redundancy group.
|
| The System Congestion Current Statistics table details.
|
| The System Congestion Interval Statistics details.
|
| System Congestion status status/statistics details.
|
transcodeInfo | (Available only on SWe except S-SBC SWe)
|
transcodeType | (Available only on SWe except S-SBC SWe) Shows type of transcode information used (CPU, GPU, CPU + GPU, HWDSP). This is system level information and shows only one entry in case of HA system. |
Admin
Command Syntax
> show status system admin <system name>
Command Parameters
Admin Attributes
Parameter | Description |
|---|---|
<system name> | System name |
actualSystemName | System name given by the user as user/metadata |
clusterId | clusterID instance present in the userdata |
savedConfigurations | A list of saved configurations, by revision number and the timestamp when the configuration was saved. Applicable for SBC SWe N:1 HA clusters that are configured to use OAM node configuration. |
sftpUserPassword | Password rules for SFTP user |
adSyncModuleName | Specifies the AD server |
adSyncStatus | Displays AD server sync status Specifies one of the following status values:
|
adTimeStamp | The timestamp of the last successful sync operation |
Announcements
Announcement file status and statistics.
Command Syntax
> show status system announcements
Command Parameters
Announcements Attributes Announcement segment NP memory usage. Announcement segment file status.
Parameter Description memoryUsagecachedSegments – Number of announcement segments cached in NP memory.totalCacheMemory – Total amount of segment cache memory available in NP.totalPlayoutTime – Total playout time of all segments cached in NP memory.totalSegments – Total number of announcement segments on disk.usedCacheMemory – Amount of segment cache memory being used in NP.utilizedCacheMemory – Percentage of segment cache memory being used in NP.segmentStatus <segment ID>audioFormat – Compression type of audio data.audioLength — Length of audio data in segment file.pathname – Pathname of segment file.playoutDuration – Playout duration of segment file.state – State of segment.totalPlays – Total number of times this segment has been played.useCount – Number of announcements currently using this segment.version – Version number of segment file.
AD Sync Status
Command Syntax
> show status system adSyncStatus
Command Parameters
adSyncStatus Command Parameters
| Parameter | Description |
|---|---|
| adSyncStatus | Displays AD server sync status |
Daughter Board Status
Command Syntax
> show status system daughterBoardStatus
Command Parameters
Daughter Board Status Attributes Daughter board identifier SBC 5000 series: SBC 7000 series: A card’s programmed firmware version (using FPGA build date) NOTE: This maintenance field does not apply to SPS100 cards. Number of module boot failures since the last successful module boot, for use during diagnostic testing of a potentially failed module. NOTE: This maintenance field does not apply to SPS100 cards. Operational state of daughter board. NOTE: For 5x00 systems, only the “enabled” state displays in the results. Identifies the serial number of the module (if present)
Parameter Description daughterBoardStatus<server name> – Server name daughterBoardIdSPS100 – SBC 5x00 SPS100 moduleDB0 – SBC 5x00 SPS100DB 0 moduleDB1 – SBC 5x00 SPS100DB 1 moduleDSP20 – SBC 5x10 DSP20 moduleDSP25 – SBC 5x10 DSP25 moduleFRU_DSP1 – SBC 7000 DSP-LC slot 1FRU_DSP2 – SBC 7000 DSP-LC slot 2FRU_DSP3 – SBC 7000 DSP-LC slot 3FRU_DSP4 – SBC 7000 DSP-LC slot 4fpgaVersionimageLoadFailureCountoperationalStatusdisabled – Card is disabled.dryup – Card is enabled but in the process of drying up. Once completed, card will be set to ‘disabled’.enabled – Card is enabled.failed – If a DSP2x or DSP-LC module fails to boot over three consecutive tries (typically due to a hardware failure), it is taken out of service and marked as state “failed”. The rest of the system continues to boot normally, including any other DSP modules. The module failure is logged/alarmed with trap “sonusConnexIpSystemCESlotFailedNotification”. The slot remains in the failed state until the module is disabled and re-enabled once a replacement card is installed.loading – Card is enabled but in the process of booting. Resources are not yet available. Once completed, card will be set to ‘enabled’.locked – Slot capacity is locked out due to mismatch (with “preserveRedundancy” configured).partNumThe part number of the module (if present) presentIndicates if the module is present or not. productNameIdentifies manufacturer name of module (if present) serialNum
DSP
DSP Resources
Command Syntax
> show status system dspRes dspCallCurrentStatistics dspCallIntervalStatistics dspUsageCurrentStatistics dspUsageIntervalStatistics
Command Parameters
DSP Resources Attributes
| Parameter | Description |
|---|---|
|
|
dspCallCurrentStatistics | The System Call DSP Resource Current table containing the following information: The following statistics are collected in this table for each codec.
|
dspCallIntervalStatistics | The System Call DSP Resource Interval table containing the following statistics for the 'n' number of intervals:
|
dspUsageCurrentStatistics | The DSP Resource statistics details. The following statistics are collected in this table for each codec. Statistics are collected once per second.
For information on the supported codecs, refer to Audio Codecs. |
dspUsageIntervalStatistics | The DSP Resource Interval table containing the following statistics over the 'n' number of intervals. Interval statistics are weighted per codec type.
For information on the supported codecs, refer to Audio Codecs. NOTE: The number of available transcoded calls depends on whether or not back-to-back transcoding is required. Also, DSP resources are commonly held during call setup (even when transcoding ultimately is not required on the call). At a high call rate this can marginally cut into the number of DSP resources available on the system. |
DSP Status
This statistic command provides the current number of transcoded sessions per DSP2x slot (SBC 5x10) or SPS100 module (SBC 5x00) depending upon the number of modules installed for the specified system. The SBC 5x10 can include up to four DSP modules. The SBC 5x00 can be configured for up to three SPS100 modules
(Refer to DSP Channel Densities for SBC 5xx0 and 7000 for details).
Command Syntax
> show status system dspStatus dspUsage
Command Parameters
DSP Status Attributes The below fields display raw count of DSP resources (i.e. channels) in use on each slot to aid in understanding which slots are loaded and to what extent in case card removal/hot swap is necessary. For each DSP codec, a Additional fields:
Parameter Description dspStatus dspUsage<system name> – The SBC system name.slot1ResourcesUtilizedslot2ResourcesUtilizedslot3ResourcesUtilizedslot4ResourcesUtilized<codec>Total and <codec>Utilization field displays. <codec>Total field indicates how many transcoding sessions the system can support for that codec to G.711.<codec>Utilization field indicates what percent of those sessions are actually in use.
NOTE: For compressed-to-compressed transcoding, two resources are required, one for each codec. amrNbTotal – Total AMR–NB resource capacity on this server.amrNbUtilization – Percentage utilization of AMR–NB resources on this server.amrNbT140Total - Total AMR-NB with T.140 resource capacity on this server.amrNbT140Utilization - Percentage utilization of AMR-NB with T.140 resources on this server.amrWbTotal – Total AMR–WB resource capacity on this server.amrWbUtilization – Percentage utilization of AMR–WB resources on this server.amrWbT140Total - Total AMR-WB with T.140 resource capacity on this server.amrWbT140Utilization - Percentage utilization of AMR-WB with T.140 resources on this server.compressionAllocFailures – Running count of resource allocation failures due to resource exhaustion.compressionAvailable – Actual compression resources currently available in real time. This essentially equates to the total number of G.711 resources after loading.compressionHighPriorityUtilization - Percentage utilization of compression resources used for high priority calls on this server.compressionTotal – Maximum number of compression resources on the server (i.e. before loading, so this number is static). This essentially equates to the total number of G.711 resources before loading (i.e. lightest codec).compressionUtilization – Percentage of compression resources in use (accounting for various codec weights). This can be calculated using the formula (compressionTotal – compressionAvailable) / compressionTotal.
NOTE: Use this value when determining the extent of DSP module load (regardless of codec type).ecmTotal – Total T.38 ECM resource capacity on this server.ecmUtilization – Percentage utilization of T.38 ECM resources on this server.ecmV34Total – Total T.38 ECM V.34 resource capacity on this server.ecmV34Utilization – Percentage utilization of T.38 ECM V.34 resources on this server.efrTotal – Total EFR resource capacity on this server.efrUtilization – Percentage utilization of EFR resources on this server.evrc0Total – Total EVRC0 resource capacity on this server.evrc0Utilization – Percentage utilization of EVRC0 resources on this server.evrcb0Total – Total EVRCB0 resource capacity on this server.evrcb0Utilization – Percentage utilization of EVRCB0 resources on this server.g711SsTotal – Total G711SS (silence suppression) resource capacity on this server.g711SsUtilization – Percentage utilization of G711SS (silence suppression) resources on this server.g711Total – Total G711 resource capacity on this server.g711Utilization – Percentage utilization of G711 resources on this server.
NOTE: The g711Utilization includes g711 channels in use plus channels that are reserved but not activated as part of the call set up process. In this case, ensure to reserve enough resources to account for the worst case codec. For example, in release 4.2.x, a reserved channel is about 4.5 times as expensive as a G.711 channel. g711V8Total – Total G711 V8 resource capacity on this server.g711V8Utilization – Percentage utilization of G711 V8 resources on this server.g722Total – Total G.722 resource capacity on this server.g722Utilization – Percentage utilization of G.722 resources on this server.g722V8Total – Total G.722 V8 resource capacity on this server.g722V8Utilization – Percentage utilization of G.722 V8 resources on this server.g726Total – Total G726 resource capacity on this server.g726Utilization – Percentage utilization of G726 resources on this server.g726V8Total – Total G726 V8 resource capacity on this server.g726V8Utilization – Percentage utilization of G726 V8 resources on this server.g729AbTotal – Total G729A+B resource capacity on this server.g729AbUtilization – Percentage utilization of G729A+B resources on this server.g729AbV8Total – Total G729A+B V8 resource capacity on this server.g729AbV8Utilization – Percentage utilization of G729A+B V8 resources on this server.g7221Total – Total G.722.1 resource capacity on this server.g7221Utilization – Percentage utilization of G.722.1 resources on this server.g7221V8Total – Total G.722.1 V8 resource capacity on this server.g7221V8Utilization – Percentage utilization of G.722.1 V8 resources on this server.g7231Total – Total G723.1 resource capacity on this server.g7231Utilization – Percentage utilization of G7231 resources on this server.g7231V8Total – Total G723.1 V8 resource capacity on this server.g7231V8Utilization – Percentage utilization of G7231 V8 resources on this server.ilbcTotal – Total iLBC resource capacity on this server.ilbcUtilization – Percentage utilization of iLBC resources on this server.ilbcV8Total – Total iLBC V8 resource capacity on this server.ilbcV8Utilization – Percentage utilization of iLBC V8 resources on this server.opusTotal – Total OPUS resource capacity on this server.opusUtilization – Percentage utilization of OPUS resources on this server.silk16Total – Total Silk16 resource capacity on this server.silk16Utilization – Percentage utilization of Silk8 resources on this server.silk8Total – Total Silk8 resource capacity on this server.silk8Utilization – Percentage utilization of Silk8 resources on this server.toneAllocFailures – Percentage of tone resource allocation failures on this server.toneAvailable – Number of tone resources currently unused and available on this server.toneHighPriorityUtilization - Percentage utilization of tone resources used for high priority calls on this server.toneTotal – Total tone resource capacity on this server.toneUtilization – Percentage utilization of tone resources on this server.evsTotal - Total EVS resource capacity on this server.evsUtilization - Percentage utilization of EVS resources on this server.evsT140Total - Total evsT140 resource capacity on this server.evsT140Utilization - Percentage utilization of evsT140 resources on this server.
Ethernet Port
The SBC 5400 firmware/software is enhanced in 8.0 to add support for one Gbps speeds to the management ports (in addition to the existing 100 Mbps support), including the support of half or full duplex with auto-negotiation on all four management ports. Each management port auto-negotiates the speed/mode independently from other management ports.
Additionally, the SBC Core is enhanced to display the negotiated management port speed and current bandwidth for all management ports from the CLI/EMA.
Since this enhancement allows one Gbps traffic bandwidth for all management ports, it increases the possibility of a traffic overload condition due to the increased bandwidth of the combined management, media and signaling traffic. To address this, the SBC sets the management traffic as the lowest priority. Thus, the system drops the management packets, as necessary, to avoid impacting media or signaling traffic.
Command Syntax
show status system ethernetPort mgmtPortStatus
mgmtPortStatus GARNET mgt0 {
ifIndex 1;
macAddress 0:10:6b:3:da:a5;
negotiatedSpeed speed1000Mbps;
linkState admnEnabledPortUp;
duplexMode full;
rxActualBandwidth 0;
txActualBandwidth 0;
rxPackets 21316;
txPackets 1794;
rxErrors 0;
txErrors 0;
rxDropped 183;
txDropped 0;
}
mgmtPortStatus GARNET mgt1 {
ifIndex 2;
macAddress 0:10:6b:3:da:a6;
negotiatedSpeed speed1000Mbps;
linkState admnEnabledPortUp;
duplexMode full;
rxActualBandwidth 0;
txActualBandwidth 0;
rxPackets 571;
txPackets 28240;
rxErrors 0;
txErrors 0;
rxDropped 0;
txDropped 0;
}
mgmtPortStatus GARNET mgt2 {
ifIndex 3;
macAddress 0:10:6b:3:db:3b;
negotiatedSpeed speed1000Mbps;
linkState admnEnabledPortUp;
duplexMode full;
rxActualBandwidth 510;
txActualBandwidth 0;
rxPackets 456103;
txPackets 2839;
rxErrors 0;
txErrors 0;
rxDropped 201;
txDropped 0;
}
mgmtPortStatus GARNET mgt3 {
ifIndex 4;
macAddress 0:10:6b:3:db:3c;
negotiatedSpeed speed1000Mbps;
linkState admnEnabledPortUp;
duplexMode full;
rxActualBandwidth 558;
txActualBandwidth 290;
rxPackets 326895;
txPackets 1263198;
rxErrors 0;
txErrors 0;
rxDropped 0;
txDropped 0;
}
[ok]
Command Syntax
> show status system ethernetPort mgmtAdmin mgmtPortStatus mgmtStatistics packetAdmin packetPortStatus packetStatistics portMonitorStatus portRedundancyGroupStatus
Command Parameters
Ethernet Port Attributes
| Parameter | Description |
|---|---|
mgmtAdmin | Management ports. |
mgmtPortStatus | Management port status details.
|
mgmtStatistics | Management port transmit and receive statistics.
|
packetPortStatus | Packet port status details.
|
packetStatistics | Packet port transmit and receive statistics.
|
portMonitorStatus | The port monitor status.
|
portRedundancyGroupStatus | Status of the port redundancy group.
|
License
Command Syntax
> show status system
licenseDomainBundleInfo
licenseInfo
licenseNodeLockedBundleInfo
licenseStatus
Command Parameters
Note
The following object only applies to the show table system command:
licenseRequired
License Attributes License details for the domain licenses available on the SBC. The license status for all installed license features or for a specified License details for the legacy licenses stored on the SBC. Displays the (Applies to 'show table' command only) NOTE: This attribute only applies if the current The CE license status table describes the current CE license state, for example "
Parameter Description licenseDomainBundleInfoactiveLicenseModebundleName – License bundle nameexpirationDate – License expiration datefeatureName – license keys for each licensed featuregenerationDate – The date the license was generatedinstallDate – The date the license was installedlicenseId – License IDlineId – The line ID for the license feature entrypurchaseOrderId – The purchase order ID specified when the license was generatedusageLimit – Usage limit for the licensed featurelicenseInfo<featureName> <licenseID> combination.<featureName> – license keys for each licensed feature:DSP-AMRNBDSP-AMRWBDSP-EVRCDSP-EVSDSP-G722DSP-SILKENCRYPTLB-INSTANCEMARKETPLACE-ROOTMEDIA-PROBENOTRUFPOL-BASEREG-GRACESBC-1X10GMPSBC-4X1GMPSBC-CAPACITYSBC-LBSBC-LISBC-MRF-RTUSBC-NICERECSBC-P-DCS-LAESSBC-POL-E911SBC-POL-ENUMSBC-POL-RTUSBC-PSX-RTUSBC-RTUSBC-SIP-ISBC-SIP323SBC-SIPRECSBC-SOSBC-RTUSBC-VIDEOSRTPSWE-INSTANCEVDSP-RTUWEBSOCKET<license ID> – License identifierexpirationDate – The expiration date for a licensed featureinUse – The number of licenses used by the SBC for this featurelicenseId – License identifiersource – Source of the license (BuiltIn, domain, or nodeLocked)usageLimit – The maximum count allowed for this featurelicenseNodeLockedBundleInfobundleName – License bundle namefeatureName – license keys for each licensed featurelicenseId – License IDexpirationDate – License expiration dateusageLimit – Usage limit for the licenseactiveLicenseMode – The licensing mode currently in use by the SBC (domain/nodeLocked)licenseRequiredlicenseRequired configuration: The configured maximum number of licenses for a particular feature for a node when network-wide domain licensing is in effect.featureName – license key for a licensed featuremaxCount – The maximum number of licenses the SBC can request from the SLS.licenseMode is "domain."licenseStatusdualCe".cemode
Network Processor
Command Syntax
> show status system networkProcessorStatistics annStatistics defragStatistics digitStatistics rtcpGenStatistics
Command Parameters
MultiExcerpt named Network Processor was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro
NTP
NTP services management
Command Syntax
> show status system ntp peerStatus systemStatus
Command Parameters
Note
The following objects only apply to the show table system command:
- keys
- serverAdmin
- timeZone
NTP Attributes Displays NTP server key details. Displays status information about each NTP peer. Displays information about each NTP Server configured to provide network time. Displays system status information about NTP. This table contains Time Zone configuration. Fields include: NOTE: In an HA configuration, the Active and Standby system times and refTimes will not match in the results of this command because SBC updates NTP data independently.
Parameter Description keyskeyIdkeyTypekeyValuepeerStatusceName – The name of this SBC server.ipAddress – IP address of the CE.state – the state of the NTP peer (insynce, outofsync, reachable).stratum – A number representing the distance from the reference clock, starting at "0". Stratum 16 represents that a device is out of sync.refTime – The time this NTP peer was last updated.serverAdminipAddress – The IP address of this NTP server.version – The NTP version of this NTP server.minPoll – The minimum poll interval to this NTP server.maxPoll – The maximum poll interval to this NTP server.state – The configured state of the NTP server entry.systemStatusceName – The name of this SBC server.clock – The SBC regularly checks system time. This field represents the system time as of the last check by SBC, not the actual system time.refTime – The time this system was last updated.timeZonename – System name.zone – The current time zone.
Policy Server
Command Syntax
> show status system policyServer policyServerStatus
Command Parameters
Note
The following objects only apply to the show table system command:
globalConfig
localServer
policyServerStatus
remoteServer
Policy Server Attributes Defines global configuration applicable to all policy servers. Local (embedded) policy server configuration. Policy Server status table. Fields include: Table of softswitch remote server configurations. Fields include:
Attribute Description globalConfigcongestionControl – The SBC throttles the sending or policy requests to either active or standby PSX when this field is enabled.mgmtInterfaceGroup – The Management Interface Group to use for communicating with external PSX.reconnectTimeout – The timer parameter for re-attempting connection to a Policy Server that is in the enabled state in seconds.switchOverMode – (automatic or manual) This setting determines how the policy server is set to ACTIVE after a switchover.type – Interface type supported by policyServer.localServeraction – The action for the operation mode for this trunk groupkeepAliveTimer – The time in seconds between sending Keep Alive indications to the internal Policy Server.mode – Assignment of the Policy Server to have the active, standby, out of service or alternate role.retries – The maximum number of retransmission attempts for a transaction on this Policy Server.retryTimer – The time in milliseconds that the SBC waits for a response from the local Policy Server.state – Administrative state of the softswitch server.transactionTimer – The time in milliseconds that the SBC waits for a response from the Policy Server after sending it a transaction request.policyServerStatusallowancePercent – The number of SBC policy requests allowed by PSX. For example, an allowance of 75%, means that the SBC is skipping one out of every four policy requests. This allowance is provisioned on the PSX and enforced on the SBC when PSX Congestion Control is enabled.averageTransactionTime – Records the average time taken in milliseconds for a softswitch transaction.congestionLevel – The PSX congestion level.dataRequests – The cumulative number of data requests received from the softswitch.index – Identifies the softswitch entry.interfaceIpAddress – Identifies the IP address the SBC uses to communicate with the PSX for this Policy Server.ipAddress – IP Address of the softswitch server.negotiatedVersion – The lowest negotiated protocol version between the gateway and all the active and alternate softswitches.operState – Operational state of the softswitch.queriesSkippedAndRejected – The cumulative number of rejected Policy Requests while the active PSX is congested and a standby PSX is either congested or not available.queriesSkippedAndServiced – The cumulative number of Policy Requests serviced by the standby PSX while the active PSX experienced congestion.redirectRequests – The cumulative number of redirect requests received from the softswitch.releaseRequests – The cumulative number of release-call requests received from the softswitch.serverReconnects – The number of successful reconnections between the gateway and the softswitch.transactionCompleted – The number of successful transactions between the gateway and the softswitch.transactionFailedAttempts – The number of unsuccessful transactions between the gateway and the softswitch.transactionRetryAttempts – The number of transaction retries between the gateway and the softswitch.version – The negotiated protocol version between the gateway and the softswitch.remoteServername – Remote server name.ipAddress – IP adddress of the remote server.portNumber – The IP port number of the softswitch server.state – Administrative state of the softswitch server.mode – Policy Server mode (active, standby, out of service or alternate role).action – The method by which queued transactions are processed when oper-state goes to standby or out-of-service. Possibilities include:dryup – all queue entries are processed to completion unless retries expires.force – all queue transactions are dropped immediately.transactionTimer – The time in milliseconds that the SBC waits for a response from the Policy Server after sending it a transaction request.keepAliveTimer – The time in seconds between sending Keep Alive indications to the Policy Server.retryTimer – The time in milliseconds that the SBC waits for a response from the Policy Server after retransmitting the transaction request.retries – The maximum number of retransmission attempts for a transaction on this Policy Server.subPortNumber – The port number assigned for the IP address of the Policy Server for the specific purpose of communicating subscriber data.
Security
Security management status/statistics details.
Command Syntax
> show status system security ocspProfileUses ocspStatistics pki
Command Parameters
Note
The following objects only apply to the show table system command:
certExpiryCheck
ipsec
Security Attributes Checks for expired certificates, trust anchor validity, and if certificates have been revoked if OSCP is enabled. Fields include: IPsec configuration. This table contains OCSP profile usage status. Fields include: This table contains OCSP Statistics. Fields include:
Parameter Description certExpiryCheckcertReCheckRate – The rate, in hours, to recheck certificates for TLS sessions.expirationPeriodicWarning – Interval of the periodic warnings in days generated after the certificate has reached the expiry threshold.expiryWarningThreshold – The number of days before generating a warning for a certificate nearing expiry.hashEventLogsShows the existence of an entry in the PrivateKeyName fields. If there is a PrivateKeyName entry displayed, this indicates that a private key is configured. ipsecikeDpdInterval – The Dead Peer Detection interval.ikeRetransmitInterval – The IKE retransmit interval period in seconds.ikeRetrasmitCount – The number of IKE retransmits.ocspProfileUsesocspName tlsName ocspTlsRefNumocspStatistics ocspInternalErrors – Number of internal error responses.ocspMalformedRequests – Number of malformed request responses.ocspRepondersUnreachable – Number of times OCSP responders are unreachable.ocspRequestAttempts – Number of OCSP request attempts that have been made.ocspResponseTimeouts – Number of times OCSP response timeouts are encountered.ocspResponsesGood – Number of OCSP Responses received with 'Good' status.ocspResponsesRevoked – Number of OCSP Responses received with 'Revoked' status.ocspResponsesUnknown – Number of OCSP Responses received with 'Unknown' status.ocspSigRequired – Number of 'sigRequired' responses.ocspTryLaters – Number of 'tryLater' responses.ocspUnauthorized – Number of unauthorized responses.pkicertStatistics– Certificate statistics.caCerts – Number of installed CA/remote certificates.localCerts – Number of installed local certificates.certificate – Collection of certificates configured on the SBC.encoding – The encoding type of the certificate.fileName – The certificate content file namepassPhrase – Pass-phrase to decrypt RSA private key in PKCS12 file.state – The administration state of this certificate.status – The status of the certificate.duplicate – The same certificate already exists in the database.expiredfailed – General error (Example: bad key length)parse-error – Certificate parsing failed (Example: password verification failed)success – Certificate was successfully added.type – The type of the certificate:remote – certificate is imported from remote location.local – certificate is used locally.local-internal – local certificate with private key generated on the SBC.
Command Examples
To view announcements memory usage:
To view base MAC address:
To view coredump list:
To view Daughterboard status (SBC 7000 example is below):
To view DSP usage:
Note
This example includes several results in the form of <codec>V8Total or <codec>V8Utilization. These entries apply if you allowed support for T.38 version 3 (also called V.34 fax transcoding). If you enabled T.38 version 3, you must enable a V.8 signaling detector for all voice codecs.
To view Ethernet Port packet statistics:
To view hard disk usage:
To view systemCongestionIntervalStatistics:
To view system congestion status details.
To view system congestion current statistics.
To view Micro Flow stats:
To display the current HA configuration settings:
To display the D-SBC Sig Port statistics:
To display sync status of active and standby nodes created through a N:1 redundancy group:
To view the status of the Load Balancing Service on S-SBC:
To view the status of the Load Balancing Service on M-SBC:
Overview
Content Tools