You are viewing an old version of this page. View the current version.

Compare with Current View Page History

Version 1 Current »

The SBC is enhanced to include the native Linux commands ping and traceroute (and their IPv6 variants) from the SBC command line interface. To use the commands at the SBC application level, log on to the SBC as an application administrator.

Note

For an HA pair configuration, you can run CLI commands ping and traceroute (and their IPv6 versions) from the active CE; switchover is needed to run the CLI commands from standby CE.

The enhancement is useful when you want to use the commands to test node connectivity and other network issues without leaving the application command line.

Note

The commands, options, and syntax available from the SBC CLI are exactly same as Linux and Unix platforms.

Command Syntax

Note
  • For IPv6 addresses, use ping6 and traceroute6.
  • Execute the commands without entering the configure private mode of the SBC.

ping

> ping 
	[-LRUbdfnqrvVaAD] 
	[-c <count>] 
	[-i <interval>] 
	[-w <deadline>] 
	[-p <pattern>] 
	[-s <packetsize>] 
	[-t <ttl>] 
	[-I <interface>] 
	[-M <pmtudisc-hint>] 
	[-m <mark>] 
	[-S <sndbuf>] 
	[-T <tstamp-options>] 
	[-Q <tos>] 
	[hop1 ...] 
	<destination_IPv4_address>

ping6

> ping6 
	[-LRUbdfnqrvVaAD] 
	[-c <count>] 
	[-i <interval>] 
	[-w <deadline>] 
	[-p <pattern>] 
	[-s <packetsize>] 
	[-t <ttl>] 
	[-I <interface>] 
	[-M <pmtudisc-hint>] 
	[-m <mark>] 
	[-S <sndbuf>] 
	[-T <tstamp-options>] 
	[-Q <tos>] 
	[hop1 ...] 
	<destination_IPv6_address>

traceroute

> traceroute 
	[ -46dFITnreAUV ] 
	[ -f <first_ttl> ] 
	[ -g gate,... ] 
	[ -i <device> ] 
	[ -m <max_ttl> ] 
	[ -N <squeries> ] 
	[ -p <port> ] 
	[ -t <tos> ] 
	[ -l <flow_label> ] 
	[ -w <waittime> ] 
	[ -q <nqueries> ] 
	[ -s <src_addr> ] 
	[ -z <sendwait> ] 
	[ --fwmark=<num> ] 
	host 
	[ <packetlen> ]

traceroute6

> traceroute6 
	[ -46dFITnreAUV ] 
	[ -f <first_ttl> ] 
	[ -g gate,... ] 
	[ -i <device> ] 
	[ -m <max_ttl> ] 
	[ -N <squeries> ] 
	[ -p <port> ] 
	[ -t <tos> ] 
	[ -l <flow_label> ] 
	[ -w <waittime> ] 
	[ -q <nqueries> ] 
	[ -s <src_addr> ] 
	[ -z <sendwait> ] 
	[ --fwmark=<num> ] 
	host 
	[ <packetlen> ]

 

Parameter Descriptions

For parameter descriptions and other information on the ping and traceroute commands and their IPv6 variants, refer to the Linux manual pages on the internet. Alternatively, you may refer to the manual pages installed as part of the Linux platform on the SBC. To access the manual pages installed on the SBC:

  • Log on to the SBC as root.
  • Execute the command:

    # man <command>

Configuration Examples

Note
  • For IPv6 addresses, use ping6 and traceroute6.
  • Execute the commands without entering the configure private mode of the SBC.

ping

> ping -c 3 10.31.200.50

PING 10.31.200.50 (10.31.200.50) 56(84) bytes of data.
64 bytes from 10.31.200.50: icmp_req=1 ttl=255 time=5.28 ms
64 bytes from 10.31.200.50: icmp_req=2 ttl=255 time=5.69 ms
64 bytes from 10.31.200.50: icmp_req=3 ttl=255 time=4.34 ms--- 10.31.200.50 ping statistics ---
3 packets transmitted, 3 received, 0% packet loss, time 2000ms
rtt min/avg/max/mdev = 4.340/5.106/5.693/0.566 ms

ping6

> ping6 -c 2 0000:0000:0000:0000:0000:0000:0000:0001

PING 0000:0000:0000:0000:0000:0000:0000:0001(::1) 56 data bytes
64 bytes from ::1: icmp_seq=1 ttl=64 time=0.031 ms
64 bytes from ::1: icmp_seq=2 ttl=64 time=0.060 ms--- 0000:0000:0000:0000:0000:0000:0000:0001 ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 999ms
rtt min/avg/max/mdev = 0.031/0.045/0.060/0.016 ms

traceroute

> traceroute 10.31.200.50

traceroute to 10.31.200.50 (10.31.200.50), 30 hops max, 60 byte packets
1 10.31.200.50 (10.31.200.50) 9.487 ms 9.493 ms 9.491 ms

traceroute6

> traceroute6 0::0.0.0.0

traceroute to 0::0.0.0.0 (::), 30 hops max, 80 byte packets
1 localhost (::1) 0.033 ms 0.009 ms 0.008 ms

 

  • No labels