EdgeMarc 6000 Back Panel
When lit, the Power LED indicates power is applied to the system. The Status LED changes to indicate the current state of the system. See the following table.
EdgeMarc 6000 Back Panel LEDs
| LED | Indicator | Description |
|---|---|---|
| Power | Off | Power is not supplied to the device. |
| Solid Green | Power is supplied to the unit. | |
| Status | Off | Power is not supplied to the device, or the bootloader failed to load. |
| Solid Amber | The device is running a self-test and is initializing. | |
| Flashing Amber | The device is upgrading its software. | |
| Flashing Green | The device is loading the EdgeMarc VoIP Operating System (VOS). | |
| Solid Green | VOS is ready. | |
| Red | The device is in the bootloader. The kernel will change the LED to solid amber once the kernel starts loading. | |
| SFP Link (1-2) | Solid Green | Peer link is powered. |
| Flashing LED | Fiber traffic is active. | |
| T1/E1 (1-2) | Off | T1/E1 port is not in use. |
| Solid Green | T1/E1 port is in use. | |
| Line (1-2) | Off | PSTN line is not in use. |
| Solid Green | PSTN line is in use. | |
| Phone (1-8) | Off | Phone is in the on-hook state. |
| Solid Green | Phone is in the off-hook state. |
EdgeMarc 6000 Back Panel Components
| Physical Label/Type | Function | Description |
|---|---|---|
| Erase button | Erase | Press the Erase button in quick succession to control the following:
Note: When restored to factory default settings, the current configuration is lost, disconnecting all VoIP devices, Internet connectivity, and network access for computers until the system is reconfigured. |
| Power Inlet | Accepts power input | This is a 12V 6A DC power socket. |
| Power/Status LEDs | System power and status | Refer to EdgeMarc 6000 Back Panel LEDs for system and power status details. |
| Ethernet WAN ports 1-2 | WAN | 2x1 10/100/1000 Mbps RJ45 Ethernet ports for WAN network connectivity (Copper). |
| SFP Link LEDs | Status | When lit, the SFP port is active and the copper RJ45 port is inactive. Refer to EdgeMarc 6000 Back Panel LEDs. |
| Optical WAN SFP ports 1-2 | WAN | Small Form-Factor Pluggable (SFP) for fiber (RJ45) Gigabit Ethernet connectivity. Either the SFP port (operating at 100/1000 Mbps) or the RJ45 (operating at 10/100/1000 Mbps) port can be active at a time. |
| Ethernet LAN ports 1-4 | LAN | 2x2 10/100/1000 Mbps RJ45 Ethernet ports for LAN network connectivity. |
| LTE Micro SIM Slot | 4G LTE Support | Allows you to insert a 4G LTE micro SIM card thus allowing 4G network access. |
| Micro SD Card Interface | Storage | Allows the Unable to show "metadata-from": No such page "_space_variables" to save configurations and other files to an SD High Capacity (SDHC) Version 2.0 card. Maximum storage capacity is 32 GB per SD card, 4 GB per file. The SD card capabilities are configured with the web-based configuration menu and with command-line interface (CLI). Refer to Unable to show "metadata-from": No such page "_space_variables" MicroSD Card Specifications. |
| USB 3.0 port | Data transmission | Can be used to connect USB devices. |
| T1/E1 LEDs | Status | When lit, the T1/E1 port is active. Refer to EdgeMarc 6000 Back Panel LEDs. |
| T1/E1 PRI ports 1-2 | T1/E1 | Allows the user to transmit voice and data through PRI. 2 x T1/E1 default system configuration. Two ports are available on the main board. |
| Line ports 1-2 | FXO | 2 x RJ11 ports for 2 FXO channels. |
| Phone ports 1-8 | FXS | 8 x RJ11 ports for 8 FXS channels. |
| FXO/FXS LEDs | Status | Refer to Table 2-2 for FXO/FXS LED status details. |
| Management Console ports | Management | RJ45 serial craft port for console management. This port is used for debug or diagnostic purposes only. Primary system configuration is performed from a web browser as described in the EdgeMarc User Guide. |
Overview
Content Tools