You must follow these steps completely and in the order shown. Failure to do so increases the risk of node failure.
In this section....
For details on troubleshooting, see Troubleshooting Cloud Connector 6.1.2.
This page provides a step-by-step procedure for Non High Availability Deployment on SBC Edge CCE. The following diagram shows typical CCE deployment scenarios on a PSTN site. The PSTN site is a combination of Cloud Connector instances, deployed at the same location, and with common PSTN gateways pool connected to them. PSTN sites allow you to: Provide connectivity to gateways that are closest to your users. Allow for scalability by deploying multiple Cloud Connector instances within one or more PSTN sites. Allow for high availability by deploying multiple instances of Cloud Connector within a single PSTN site. CCE Deployment Scenarios
Before You Start
CCE Deployment Scenarios
Scenario 3 and Scenario 4 are covered in Configuring the SBC Edge for Two CCEs. This document contains steps for Scenario 1 and Scenario 2 deployments. An Office 365 tenant with an E5 license or E3 + Cloud PBX. You must have the Global Administrator role for your O365 tenant account. A public certificate authority ready to sign a certificate for the SBC Edge. Important! Read the steps outlined in Certificate Requirements at Microsoft Technet. A properly configured firewall. See Ports and Protocols at Microsoft Technet. Latest System Release SBC Firmware and SbcComms Firmware Important!Prerequisites
A public domain name prepared and mapped with your Office 365 tenant (for example, "mydomain.com"). See Create an Office 365 Tenant. An entry on your public domain name that points to the fixed IP address of your SBC Edge (for example, myccesite1.mydomain.com" with an IP address of "nn.nn.mm.nn"). Microsoft Cloud Connector Edition image on ASM recovery partition.
For this best practice, Cloud Connector Edition deployment follows the cabling shown below:
Typical Deployments
For this best practice, the Router/Firewall is configured using the following rules:
Internal Firewall Rules
Source IP | Destination IP | Source Port | Destination Port |
---|---|---|---|
Cloud Connector Mediation component | Internal clients | TCP 49 152 – 57 500* | TCP 50,000-50,019 (Optional) |
Cloud Connector Mediation component | Internal clients | UDP 49 152 – 57 500* | UDP 50,000-50,019 |
Internal clients | Cloud Connector Mediation component | TCP 50,000-50,019 | TCP 49 152 – 57 500* |
Internal clients | Cloud Connector Mediation component | UDP 50,000-50,019 | UDP 49 152 -57 500* |
External Firewall Rules
Source IP | Destination IP | Source Port | Destination Port |
---|---|---|---|
Any | Cloud Connector Edge External Interface | Any | TCP 5061 |
Cloud Connector Edge External Interface | Any | Any | TCP 5061 |
Cloud Connector Edge External Interface | Any | Any | TCP 80 |
Cloud Connector Edge External Interface | Any | Any | UDP 53 |
Cloud Connector Edge External Interface | Any | Any | TCP 53 |
Cloud Connector Edge External Interface | Any | TCP 50,000-59,999 | Any |
Cloud Connector Edge External Interface | Any | UDP 3478 | Any |
Cloud Connector Edge External Interface | Any | UDP 50,000-59,999 | Any |
Any | Cloud Connector Edge External Interface | Any | TCP 443 |
Any | Cloud Connector Edge External Interface | Any | TCP 50,000-59,999 |
Any | Cloud Connector Edge External Interface | Any | UDP 3478 |
Any | Cloud Connector Edge External Interface | Any | UDP 50,000 - 59,999 |
Host Firewall Rules - Internal or External Access
Source IP | Destination IP | Source Port | Destination Port |
---|---|---|---|
ASM | Any | Any | TCP 53 |
ASM | Any | Any | TCP 80 |
ASM | Any | Any | TCP 443 |
Make sure that CCE FQDN is resolving to the
Update the
Ensure That the Node FQDN is Correct
Optionally, if you want to configure a secondary
If your ASM have been used before, you should re-Initialize it now. Refer to Re-Initializing the ASM for details.
Confirm that the ASM is ready to deploy the Cloud Connector Edition. To do so:
Step | Action |
---|---|
1 | Login to the WebUI of the SBC Edge. |
2 | Click the Task tab and then select Operational Status. |
3 | Verify the following:
|
Operational Status
After you update the ASM, change its Admin Password.
Step | Action |
---|---|
1 | Login to the WebUI of the SBC Edge. |
2 | Click the Settings tab and then click Change Admin Password. |
3 | Enter and confirm your new password and then click OK. |
New Admin Password
Deploying the CCE on the
Step | Action |
---|---|
1 | Login to the WebUI of the SBC Edge. |
2 | Navigate to Tasks > Office 365 Cloud Connector Edition> Setup. |
3 | Click the ASM Config tab and configure/verify the Network and IP settings of your ASM. |
4 | From the Remote Desktop Enabled drop down list, select Yes (to enable Remote Desktop) or No (to disable Remote Desktop). |
5 | From the Windows Firewall Enabled drop down list, select Yes (to enable Windows Firewall) or No (to disable Windows Firewall). |
6 | From the Proxy Enabled drop down list, Enables use of the Proxy Server on the ASM. Select from the drop down list: Yes (enables Proxy Server on the ASM) or No (disables Proxy Server). |
7 | From the Proxy Address drop down list, select Yes (to enable the IP address for the Proxy Server in IPv4 format). This field is available only when Proxy Enabled is set to Yes. |
8 | From the Proxy Port drop down list, select Yes (to enable the port in which the Proxy Server connects). Valid entry: Valid entry: 1 - 65000. This field is available only when Proxy Enabled is set to Yes. |
9 | Configure/verify the Network and IP settings of your ASM. |
10 | Click Apply. After receiving the activity status as successfully completed, click the Generate CSR tab. |
ASM Config
This process is required only if you don't have a public certificate for your deployment. If you already have a certificate, proceed to Import Certificate.
Step | Action |
---|---|
1 | Login to the WebUI of the SBC Edge. |
2 | Navigate to Tasks > Office 365 Cloud Connector Edition> Setup. |
3 | Click the Generate CSR tab. |
4 | Generate the CSR as shown below with following information. To ensure creating a valid CSR for Cloud Connector Edition usage, please see the section "Certificate requirements" on https://technet.microsoft.com/en-us/library/mt605227.aspx. |
5 | Copy the CSR from the lower pane of the Generate CSR page and save it as a .txt file. |
6 | After the CSR is signed by the Certificate Authority and you receive the PKCS7 Certificate file, continue the wizard by clicking on CCE Public Certificate tab. |
Generate CSR
Step | Action |
---|---|
1 | Login to the WebUI of the SBC Edge. |
2 | Navigate to Tasks > Office 365 Cloud Connector Edition and click the CCE Public Certificate tab. |
3 | Click the Action drop-down list and select the appropriate option:
|
4 | After receiving the activity status as successfully completed, click on Configure CCE tab. |
CCE Public Certificate
If you configure TLS and downgrade the system to a release prior to Release 7.0, the Exchange CA Certificate for TLS will be unavailable; you must re-deploy or upgrade to Release 7.0. Along with TLS configuration on the CCE, the TLS capability requires a loaded Root CA certificate and a signed certificate on the SBC.
Any changes to the Configure CCE tab requires the CCE to be redeployed.
Step | Action |
---|---|
1 | Login to the WebUI of the SBC Edge. |
2 | Navigate to Tasks > Office 365 Cloud Connector Edition> Setup. |
3 | Click the Configure CCE tab. |
4 | Configure all necessary information and then click OK. All the pre-configured fields are valid as is, and recommended by Unable to show "metadata-from": No such page "_space_variables" . These fields may be edited, but all entries must meet Microsoft requirements.TLS 1.2 is supported; the following fields are required to configure TLS:
If TLS is configured as the Primary SBC Transport Protocol, you must run the Synchronize CCE/SBC CA Certificate task to allow a successful TLS handshake between CCE and SBC Edge. However, if TCP is configured as the Primary SBC Transport Protocol the Synchronize CCE/SBC CA Certificate task is not mandatory. See Managing Cloud Connector Edition Private Certificates. If the deployment environment consists of multiple-site with a single certificate or a wild card certificate, ensure the CCE Site Name and the Edge Server Public Hostname are correct before proceeding. |
5 | To increase Fast Failover (which shortens the time where certain ported numbers have a long delay from ITSP PSTN provider) configure Trunk Information: Refer Support. Indicates whether Gateways support Refer for a Call Transfer scenario. Valid entries: Enable (the Gateway(s) supports Refer which can handle call transfer) or Disable (the Gateway does not support Refer and the Mediation Server handles call transfer). Fast Failover Timer. Determines whether outbound calls that are not answered by the gateway within ten seconds will be routed to the next available trunk; if there are no additional trunks, the call will automatically be dropped. Valid entries: Enable or Disable. Forward Call History. Indicates whether call history information is forwarded through the trunk. Valid entries: Enable or Disable. Forward PAI. Indicates whether the P-Asserted-Identity (PAI) header will be forwarded along with the call. Valid entries: Enable or Disable. |
6 | After receiving the activity status as successfully completed, click the Prepare CCE tab to continue. |
Configure CCE
See Managing Cloud Connector Edition Private Certificates for the following setup options:
Step | Action |
---|---|
1 | Login to the WebUI of the SBC Edge. |
2 | Navigate to Tasks > Office 365 Cloud Connector Edition> Setup. |
3 | Click the Prepare CCE tab. |
4 | Click the Prepare CCE button. A confirmation will request you to enter the password again for the new password. Only the Tenant credentials are already existing. Click OK as shown below. |
5 | After confirmation, click on Customize CCE VMs. |
Prepare the CCE
This step stores the two Microsoft product keys, and customizes the CCE VM (which is not yet activated).
The CCE requires four VMs; each Microsoft Product Key activates two VMs.
Step | Action |
---|---|
1 | Login to the WebUI of the SBC Edge. |
2 | Navigate to Tasks > Office 365 Cloud Connector Edition> Setup. |
3 | Click the Customize CCE VMs tab. |
4 | In Domain Controller and Central Management Store VM > Windows Product Key 1, enter the first Microsoft Product Key. To identify the Product Key, see Identify Microsoft Product Key. |
5 | In Under Mediation Server and Edge Server VM > Windows Product Key 2, enter the second Microsoft Product Key.To identify the Product Key, see Identify Microsoft Product Key. |
6 | From the Proxy Usage drop down list, select Enabled (enables the Proxy Server on the DMZ facing the internal network) If you select Disable, the Proxy Server is disabled. |
7 | In the Proxy Server IP Address field, enter the server IP address for the Proxy Server in IPv4 format. This field is available only when Proxy Usage is set to Enabled. |
8 | In the Proxy Server Port field, enter the port number for the Proxy Server. Valid entry: 1 - 65535. This field is available only when Proxy Usage is set to Enabled. |
9 | Click Apply. |
10 | Access Tasks> Operational Status to verify Windows Activation. If activation fails, see Troubleshooting. |
11 | Click on CCE Private Certificate. |
Customize CCE VMs
To identify the Microsoft Product Key:
If activation fails, check the following:
Step | Action |
---|---|
1 | Remote desktop to the ASM system. |
2 | Launch the Ribbon Cloud Link Deployer from icon on the desktop. |
3 | Check the first three actions:
Select Apply. |
After the CCE is deployed, integrate the
SIP Provider (NNN.NNN.NNN.NNN) – SBC Edge (NNN.NNN.NNN.NNN) – CCE (mediation Server: NNN.NNN.NNN.NNN) – O365 Cloud |
Step | Action |
---|---|
1 | Login to the WebUI of the SBC Edge. |
2 | Click the Tasks tab, and then click SBC Easy Setup > Easy Config Wizard in the navigation pane. |
3 | Follow steps 1, 2, and 3 and click Finish. |
4 | Click OK on the next two popups to complete the setup. |
5 | The wizard configures the necessary settings for the single SBC Edge and CCE integration. Relevant configuration items are shown in the Settings tab below: |
Step | Action |
---|---|
1 | Login to the WebUI of the Secondary SBC Edge. |
2 | Click the Tasks tab and then run the Easy Config. |
3 | The preceding step will configure the Secondary SBC Edge with the appropriate configuration items. |
With the preceding settings, an endpoint from the SIP provider side can dial the number of a Skype For Business (O365) client and reach out to it over Call Flow Similarly, a Skype For Business (O365) client can dial the number of an endpoint off of ITSP and reach out to it over Call Flow Configuration changes to the CCE in the WebUI per Tasks > Setup Cloud Connector Edition> Configure CCE requires the CCE to be re-deployed. Backup the Public Certificate per Tasks > Setup Cloud Connector Edition> Import Certificate. If the CCE was previously deployed, previously installed information must be cleared in O365. To do so, follow the steps below: Connect the Office365 Tenant through a series of commands as follows: a. Execute the following command: Execute the following command to remove the appliance: Execute the following command to verify that the appliance has been removed: This completes the cleanup. The ASM must be re-initialized with the image that contains the latest CCE software . To do so: Select the appropriate image from the drop-down list and then click Apply.
Basic Call Verification after CCE Deployment and
O365 Known Issue and Workarounds for CCE
Redeploying the CCE
Clean Office 365 tenant
Step Action 1 Remote Desktop to the ASM system 2 Import-Module skypeonlineconnector
$cred = Get-Credential
$Session = New-CsOnlineSession -Credential $cred -Verbose
Import-PSSession $session
3 Display all the Appliances assigned to your tenant, identify the Appliance you just re-initialized, and copy the identity into your clipboard. Get-CsHybridPSTNAppliance
4 Unregister-CsHybridPSTNAppliance -Identity <paste the identity here> -Force
5 Get-CsHybridPSTNAppliance
6 Re-Initializing of the ASM
Step Action 1 Login to the WebUI of the SBC Edge. 2 Click the Task tab, and then click Reinitialize in the navigation pane. 3
The “.ini” file is the configuration of the Microsoft CCE (Cloud Connector Edition) running on the ASM. The contents of the ".ini" file must be as defined by Microsoft. From the Configure CCE panel, the Raw INI Config drop-down list enables you to edit, export, or import the ".ini" file.
Working with the ".ini" file allows you to provision multiple CCEs in a similar manner. Once you configure a CCE, you can export the ".ini" file, modify it for the second system, and then import the CCE. This procedure can then be repeated for the third system, etc. Also, backing up the SBC configuration and CCE configuration helps recover faster in the case of lost data.
Step | Action |
---|---|
1 | After receiving the activity status completion message, click the Click to re-configure CCE application button. |
2 | Click OK on the popup. |
4 | Click the Raw (INI) Config drop-down list, select Edit. Configurable fields are displayed for editing. Modifications to the CCE configuration requires redeployment of the CCE VM, and this action takes approximately two hours. Note: The example uses AEPSITE2 for the these attributes. |
5 | After verifying the information click OK. |
Step | Action |
---|---|
1. | After receiving the activity status completion message, click the Click to re-configure CCE application button. |
2. | Click OK on the popup. |
3. | From the Raw (INI) Config drop down list, select Import or Export.
|
Follow these steps if you need to update the O365 tenant admin password or account.
Step | Action |
---|---|
1 | On the WebUI, click Tasks and select the Prepare CCE tab (see Preparing the CCE). |
2 | Click Prepare CCE. |
3 | From the Password Setting drop down list, select Change Password. Keep the same passwords for the Edge Server, CCE Service and CA Backup File, but change the passwords for Tenant Account User and Tenant Account Password. |
4 | On Remote desktop, start the Ribbon Cloud Link Deployer, and check Transfer Password from SBC to reset the credentials. |
For details on Certificates, refer to Generating Certificate Signing Requests.
Follow these steps to renew the CCE Public Certificate.
Step | Action |
---|---|
1 | On the WebUI, click Tasks and select the Generate CSR. |
2 | Sign the certificate with your public CA. |
3 | Import the new certificate into the Public Certificate tab. |
4 | Transfer the Certificate to the SBC Edge using the Public Certificate tab. |