This section describes Message Transfer Part Level 2 (MTP2) IO Manager TL1 commands. These commands are applicable to the AMC308 IO card.
IO Manager Command Groupings
The following figure shows the IO Manager objects that can be configured using TL1 commands.
IO Manager Objects Groupings
IO Manager
This section includes the following information for the I/O Manager:
IO Manager
CHG-IO-MGR
CHG-IO-MGR::[<IO Manger/Slot Number>]:[CTAG]:::::[FEATURE=<LoggingState>],[ERRORS=<LoggingState>],[PROVISIONING=<LoggingState>],[SLCONFIG=<ChanDistrib>],[PROTOVARIANT=<FlavourSelect>];
VFY-IO-MGR
VFY-IO-MGR::[<IO Manager/Slot Number>]:[CTAG];
SET-IO-MGR
SET-IO-MGR::[<IO Manager/Slot Number>]:[CTAG]:::[RESTORE_DBG];
::[<IO Manager/Slot Number>]:<BOARDTYPE=CardType>,<SLOT=int>,<HOSTNAME=string>,<SERIAL=string>,<FEATURE=LoggingState>,<ERRORS=LoggingState>,<PROVISIONING=LoggingState>,<ALSSUP=EnableType>,<AHSSUP=EnableType>,<AATMSUP=EnableType>,<ALSCOUNT=int>,<AHSCOUNT=int>,<AATMCOUNT=int>,<SLCONFIG=ChanDistrib>,<PROTOVARIANT=FlavourSelect>,<NRESTART=YesNo>;
AID Description
Slot Number - Position 1
Type: int
Description: Location of the board in the chassis.
Attribute Details
BOARDTYPE - Card Type
Permission: Read-only
Type: CardType={CPC388, CPC358, CPC324, AMC304, AMC308, AMC318, AMC348, PCE382}
Description: Hardware model name for the board.
SLOT - Slot Number
Permission: Read-only
Type: int
Description: Location of the board in the chassis.
HOSTNAME - Host Name
Permission: Read-only
Type: string
Description: Host name of this board.
SERIAL - Serial Number
Permission: Read-only
Type: string
Description: Serial number of this board.
FEATURE - Feature
Permission: Writeable
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Overall log control must be LOGGED to receive any logs.
ERRORS - Errors
Permission: Writeable
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Logging of errored function calls to board API or library functions.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
PROVISIONING - Provisioning
Permission: Writeable
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Explanatory logs regarding user input.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
ALSSUP - LSL Support
Permission: Read-only
Type: EnableType={DISABLED,ENABLED}
Description: Indicated whether support for the link type is available on the installed hardware.
AHSSUP - HSL AnnexA Support
Permission: Read-only
Type: EnableType={DISABLED,ENABLED}
Description: Indicated whether support for the link type is available on the installed hardware.
AATMSUP - HSL ATM Support
Permission: Read-only
Type: EnableType={DISABLED,ENABLED}
Description: Indicated whether support for the link type is available on the installed hardware.
ALSCOUNT - Max LSL
Permission: Read-only
Type: int
Description: Current max number of channelized low speed TDM channels.
AHSCOUNT - Max HSL AnnexA
Permission: Read-only
Type: int
Description: Current max number of AnnexA or unchannelized high speed TDM channels.
AATMCOUNT - Max HSL ATM
Permission: Read-only
Type: int
Description: Current max number of ATM channels.
SLCONFIG - Select Configuration
Permission: Writeable
Type: ChanDistrib={CHANNELS 128 0 0,CHANNELS 64 2 0,CHANNELS 0 4 0,CHANNELS 64 0 4,CHANNELS 0 2 4,CHANNELS 0 0 8}
Description: Select the channel capabilities, in order: low speed TDM - channelized - (LSL), high speed TDM - unchannelized, Q.703 Annnex A - (HSL AnnexA), high speed ATM - ATM SAAL NNI - (HSL ATM). This defines internal resource distribution. This slot must be restarted for the selection to take effect.
PROTOVARIANT - Protocol Variant
Permissions: Writeable
Type: FlavourSelect={ANSI_ITU,JAPAN}
Description: Variant for low speed protocol. Either of ANSI-ITU or JAPAN. The application must be restarted for the selection to take effect.
NRESTART - Restart Required
Permission: Read-only
Type: YesNo={No,Yes}
Description: Is a card restart required in order to have the selected configuration? Changing the Select Configuration requires a restart of this card for the new values to take effect.
LSL Channels
SET-IOCH-LSLS
SET-IOCH-LSLS::[<IO Manager/Slot Number>]:[CTAG]:::[ACT_CTRL/DEACT_CTRL];
VFY-IOCH-LSLS
VFY-IOCH-LSLS::[<IO Manager/Slot Number>]:[CTAG];
::[<IO Manager/Slot Number>]:<LICENSE=LicenseState>,<STATE=FuncStatus>;
Attribute Details
LICENSE - License
Permission: Read-only
Type: LicenseState={UNLICENSED,DISCONNECTED,LICENSED,UNKNOWN}
Description: TDM license state: Licensed, Unlicensed, Disconnected
STATE - State
Permission: Read-only
Type: FuncStatus={ACTIVATED,DEACTIVATED,FAILED}
Description: Link Manager state
LSL Channel
DLT-IOCH-LSL
DLT-IOCH-LSL::[<IO Manager/Slot Number>]-[<LSL Channel/Channel Number>]:[CTAG];
ADD-IOCH-LSL
ADD-IOCH-LSL::[<IO Manager/Slot Number>]-[<LSL Channel/Channel Number>]:[CTAG];
CHG-IOCH-LSL
CHG-IOCH-LSL::[<IO Manager/Slot Number>]-[<LSL Channel/Channel Number>]:[CTAG]:::::[CLLI=<string>],[PORT=<PortNumber>],[TIME_SLOT=<Timeslot>],[BAUD_RATE=<Baud>],[LPBK_MODE=<EnableType>];
VFY-IOCH-LSL
VFY-IOCH-LSL::[<IO Manager/Slot Number>]-[<LSL Channel/Channel Number>]:[CTAG];
::[<IO Manager/Slot Number>]-[<LSL Channel/Channel Number>]:<CHANNEL_NUMBER=int>,<CLLI=string>,<PORT=PortNumber>,<TIME_SLOT=Timeslot>,<BAUD_RATE=Baud>,<L3U=ChannelStatus>,<LPBK_MODE=EnableType>,<SUPP_DBG=string>,<MTP3_API=LoggingState>,<LSSU=LoggingState>,<FISU_MSU=LoggingState>;
AID Description
Channel Number - Position 1
Type: int
Description: The number of the Signaling Channel being mapped.
Attribute Details
CHANNEL_NUMBER - Channel Number
Permissions: Createable
Type: int
Description: The number of the Signaling Channel being mapped.
CLLI - CLLI
Permission: Writeable
Type: string
Description: Common Language Location Identifier string for this channel.
PORT - Port
Permission: Writeable
Type: PortNumber={PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,NOT_CONFIGURED,PORT_8}
Description: The number of the I/O port with the physical connection to the link.
TIME_SLOT - Time Slot
Permission: Writeable
Type: Timeslot={NOT_CONFIGURED, 1 to 31}
Description: Timeslot on the link (1-24 T1, 1-31 E1).
BAUD_RATE - Baud Rate
Permission: Writeable
Type: Baud={DS0_64K,DS0A_56K,BAUD_48K,BAUD_48K_REV,BAUD_TTC_48K}
Description: Baud rate for the timeslot. 64K uses all 8 bits. 56K uses 7 of 8 bits and discards the LSB. 48K uses 6 of 8 bits and discards the 2 LSBs. 48K_REV uses 6 of 8 bits and discards the two MSBs. TTC_48K uses 6 of 8 bits and discards the LSB and MSB.
L3U - L3 Use
Permission: Read-only
Type: ChannelStatus={IN_USE,AVAILABLE, 1 to 1024}
Description: State of channel availability for MTP3 use (assigned number or AVAILABLE).
LPBK_MODE - Loopback Mode
Permission: Writeable
Type: EnableType={DISABLED,ENABLED}
Description: Redirects incoming data on port and timeslot back to sender (Remote end L2 alignment may be achieved). ENABLED or DISABLED
SUPP_DBG - Support Debug
Permission: Read-only
Type: string
Description: Information for debug support.
MTP3_API - MTP3 API
Permission: Read-only
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Log MTP3 API related information. Set this value at MTP3.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
LSSU - LSSU
Permission: Read-only
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Log LSSU receipt and state changes. Set this value at MTP3.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
FISU_MSU - FISU and MSU
Permission: Read-only
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Log Sequence Numbers information. Set this value at MTP3.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
LSL H.110 Channel
DLT-IOCH-H110LSL
DLT-IOCH-H110LSL::[<IO Manager/Slot Number>]-[<LSL H110 Channel/Channel Number>]:[CTAG];
ADD-IOCH-H110LSL
ADD-IOCH-H110LSL::[<IO Manager/Slot Number>]-[<LSL H110 Channel/Channel Number>]:[CTAG];
CHG-IOCH-H110LSL
CHG-IOCH-H110LSL::[<IO Manager/Slot Number>]-[<LSL H110 Channel/Channel Number>]:[CTAG]:::::[CLLI=<string>],[CTBUS_TS_RX=<CTBusTS>],[CTBUS_TS_TX=<CTBusTS>],[BAUD_RATE=<Baud>],[LPBK_MODE=<EnableType>];
VFY-IOCH-H110LSL
VFY-IOCH-H110LSL::[<IO Manager/Slot Number>]-[<LSL H110 Channel/Channel Number>]:[CTAG];
::[<IO Manager/Slot Number>]-[<LSL H110 Channel/Channel Number>]:<CHANNEL_NUMBER=int>,<CLLI=string>,<CTBUS_TS_RX=CTBusTS>,<CTBUS_TS_TX=CTBusTS>,<BAUD_RATE=Baud>,<L3U=ChannelStatus>,<LPBK_MODE=EnableType>,<SUPP_DBG=string>,<MTP3_API=LoggingState>,<LSSU=LoggingState>,<FISU_MSU=LoggingState>;
AID Description
Channel Number - Position 1
Type: int
Description: The number of the Signaling Channel being mapped.
Attribute Details
CHANNEL_NUMBER - Channel Number
Type: int
Description: The number of the Signaling Channel being mapped.
CLLI - CLLI
Permission: Writeable
Type: string
Description: Common Language Location Identifier string for this channel.
CTBUS_TS_RX - CTBus Time Slot Rx
Permission: Writeable
Type: CTBusTS={NOT_CONFIGURED, 1 to 4096}
Description: Receive Timeslot on the CTBus (1-4096).
CTBUS_TS_TX - CTBus Time Slot Tx
Permission: Writeable
Type: CTBusTS={NOT_CONFIGURED, 1 to 4096}
Description: Transmit Timeslot on the CTBus (1-4096).
BAUD_RATE - Baud Rate
Baud={DS0_64K,DS0A_56K,BAUD_48K,BAUD_48K_REV,BAUD_TTC_48K}
Description: Baud rate for the timeslot. 64K uses all 8 bits. 56K uses 7 of 8 bits and discards the LSB. 48K uses 6 of 8 bits and discards the 2 LSBs. 48K_REV uses 6 of 8 bits and discards the two MSBs. TTC_48K uses 6 of 8 bits and discards the LSB and MSB.
L3U - L3 Use
Permission: Read-only
Type: ChannelStatus={IN_USE,AVAILABLE, 1 to 1024}
Description: State of channel availability for MTP3 use (assigned number or AVAILABLE).
LPBK_MODE - Loopback Mode
Permission: Writeable
Type: EnableType={DISABLED,ENABLED}
Description: Redirects incoming data on Tx timeslot back to Rx timeslot (Remote end L2 alignment may be achieved). ENABLED or DISABLED
SUPP_DBG - Support Debug
Permission: Read-only
Type: string
Description: Information for debug support.
MTP3_API - MTP3 API
Permission: Read-only
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Log MTP3 API related information. Set this value at MTP3.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
LSSU - LSSU
Permission: Read-only
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Log LSSU receipt and state changes. Set this value at MTP3.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
FISU_MSU - FISU and MSU
Permission: Read-only
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Log Sequence Numbers information. Set this value at MTP3.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
MTP2 Link
VFY-IOCH-MTP2LINK
VFY-IOCH-MTP2LINK::[<IO Manager/Slot Number>]:[CTAG];
::[<IO Manager/Slot Number>]:;
Attribute Details
None
HSL Annex A Channels
VFY-IOCH-HSLANNEXAS
VFY-IOCH-HSLANNEXAS::[<IO Manager/Slot Number>]:[CTAG];
CHG-IOCH-HSLANNEXAS
CHG-IOCH-HSLANNEXAS::[<IO Manager/Slot Number>]:[CTAG]:::::[USE_FISU=<EnableType>];
SET-IOCH-HSLANNEXAS
SET-IOCH-HSLANNEXAS::[<IO Manager/Slot Number>]:[CTAG]:::[ACT_CTRL/DEACT_CTRL];
::[<IO Manager/Slot Number>]:<LICENSE=LicenseState>,<STATE=FuncStatus>,<USE_FISU=EnableType>;
Attribute Details
LICENSE - License
Permission: Read-only
Type: LicenseState={UNLICENSED,DISCONNECTED,LICENSED,UNKNOWN}
Description: TDM license state: Licensed, Unlicensed, Disconnected
STATE - State
Permission: Read-only
Type: FuncStatus={ACTIVATED,DEACTIVATED,FAILED}
Description: Link Manager state.
USE_FISU - Use Repeat FISU
Permissions: Writeable
Type: EnableType={DISABLED,ENABLED}
Description: To be used only when link failures occur in the absence of clock faults and miss-configuration. Increases FISUs on the line but decreases performance.
HSL AnnexA Channel
DLT-IOCH-HSLANNEXA
DLT-IOCH-HSLANNEXA::[<IO Manager/Slot Number>]-[<HSL AnnexA Channel/Channel Number>]:[CTAG];
ADD-IOCH-HSLANNEXA
ADD-IOCH-HSLANNEXA::[<IO Manager/Slot Number>]-[<HSL AnnexA Channel/Channel Number>]:[CTAG];
CHG-IOCH-HSLANNEXA
CHG-IOCH-HSLANNEXA::[<IO Manager/Slot Number>]-[<HSL AnnexA Channel/Channel Number>]:[CTAG]:::::[CLLI=<string>],[PORT=<PortNumber>],[SEQNUMBIT=<SeqNumSize>];
VFY-IOCH-HSLANNEXA
VFY-IOCH-HSLANNEXA::[<IO Manager/Slot Number>]-[<HSL AnnexA Channel/Channel Number>]:[CTAG];
::[<IO Manager/Slot Number>]-[<HSL AnnexA Channel/Channel Number>]:<CHANNEL_NUMBER=int>,<CLLI=string>,<PORT=PortNumber>,<BAUD_RATE=HSLBaud>,<L3U=ChannelStatus>,<SUPP_DBG=string>,<SEQNUMBIT=SeqNumSize>,<MTP3_API=LoggingState>,<LSSU=LoggingState>,<FISU_MSU=LoggingState>;
AID Description
Channel Number - Position 1
Type: int
Description: Channel number
Attribute Details
CHANNEL_NUMBER - Channel Number
Permissions: Createable
Type: int
Description: Channel number
CLLI - CLLI
Permission: Writeable
Type: string
Description: Common Language Location Identifier string for this channel.
PORT - Port
Permission: Writeable
Type:PortNumber={PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,NOT_CONFIGURED,PORT_8}
Description: Port number
BAUD_RATE - Baud Rate
Permission: Read-only
Type: HSLBaud={BAUD_1_5M,BAUD_2_0M}
Description: Baud rate: T1 link requires 1.5M while E1 uses 2.0M. Autoconfigured on port selection.
L3U - L3 Use
Permission: Read-only
Type: ChannelStatus={IN_USE,AVAILABLE, 1 to 1024}
Description: State of channel availability for MTP3 use (assigned number or AVAILABLE).
SUPP_DBG - Support Debug
Permission: Read-only
Type: string
Description: Information for debug support.
SEQNUMBIT - Sequence Number Bits
Permission: Writeable
Type: SeqNumSize={STANDARD, 7 to 11}
Description: Number of sequence number bits used for the sliding window size. Reasonable values are 7-12, 12 is standard. The FSN/BSN field is 12 bits. Set before configuring channels - changes may cause link failure.
MTP3_API - MTP3 API
Permission: Read-only
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Log MTP3 API related information. Set this value at MTP3.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
LSSU - LSSU
Permission: Read-only
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Log LSSU receipt and state changes. Set this value at MTP3.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
FISU_MSU - FISU and MSU
Permission: Read-only
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Log Sequence Numbers information. Set this value at MTP3.
Values: LOGGED, NOT_LOGGED. Value OVERRIDDEN indicates the debug FEATURE is NOT_LOGGED.
HSL ATM Channels
CHG-IOCH-HSLATMS
CHG-IOCH-HSLATMS::[<IO Manager/Slot Number>]:[CTAG]:::::[VPI_MASK=<int>],[VCI_MASK=<int>];
SET-IOCH-HSLATMS
SET-IOCH-HSLATMS::[<IO Manager/Slot Number>]:[CTAG]:::[ACT_CTRL/DEACT_CTRL];
VFY-IOCH-HSLATMS
VFY-IOCH-HSLATMS::[<IO Manager/Slot Number>]:[CTAG];
::[<IO Manager/Slot Number>]:<LICENSE=LicenseState>,<STATE=FuncStatus>,<VPI_MASK=int>,<VCI_MASK=int>;
Attribute Details
LICENSE - License
Permission: Read-only
Type: LicenseState={UNLICENSED,DISCONNECTED,LICENSED,UNKNOWN}
Description: ATM license state: Licensed, Unlicensed, Disconnected
STATE - State
Permission: Read-only
Type: FuncStatus={ACTIVATED,DEACTIVATED,FAILED}
Description: Link manager state. State of FAILED indicates setup fault.
VPI_MASK - VPI Mask
Permission: Writeable
Type: int
Description: Bit mask (in decimal) that determines the valid VPI range for a link. A maximum of 4 out of 8 bits can be used. Valid options are 0 to 240. For example, mask 15 is 00001111 in binary, which gives a range of 0 to 15 for VPI. The maximum is 11110000 (240 decimal).
VCI_MASK - VCI Mask
Permission: Writeable
Type: int
Description: Bit mask (in decimal) that determines the valid VCI range for a link. A maximum of 10 out of 16 bits can be used. Valid options are 0 to 65472. For example, mask 15 is 00001111 in binary, which gives a range of 0 to 15 for VPI. The maximum is 1111111111000000 (65472 decimal).
HSL ATM Channel
DLT-IOCH-HSLATM
DLT-IOCH-HSLATM::[<IO Manager/Slot Number>]-[<HSL ATM Channel/Channel Number>]:[CTAG];
ADD-IOCH-HSLATM
ADD-IOCH-HSLATM::[<IO Manager/Slot Number>]-[<HSL ATM Channel/Channel Number>]:[CTAG]:::::[PORT=<PortNumber>];
CHG-IOCH-HSLATM
CHG-IOCH-HSLATM::[<IO Manager/Slot Number>]-[<HSL ATM Channel/Channel Number>]:[CTAG]:::::[CLLI=<string>],[VPI=<int>],[VCI=<int>],[SCRAMBLING=<EnableType>],[HEC_POLY=<EnableType>],[HEC_VERIF=<CheckLevel>],[QOS=<BitRate>],[T1=<int>],[T2=<int>],[T3=<int>],[ALIGNMENT=<Align>],[N1=<int>],[CNGS_LVL1_ONST=<int>],[CNGS_LVL2_ONST=<int>],[CNGS_LVL3_ONST=<int>],[CNGS_LVL1_ABT=<int>],[CNGS_LVL2_ABT=<int>],[CNGS_LVL3_ABT=<int>],[LOGL1=<LoggingState>],[LOGL2=<LoggingState>],[LOGL3=<LoggingState>],[LOGL4=<LoggingState>];
SET-IOCH-HSLATM
SET-IOCH-HSLATM::[<IO Manager/Slot Number>]-[<HSL ATM Channel/Channel Number>]:[CTAG]:::[ACT/DEACT];
VFY-IOCH-HSLATM
VFY-IOCH-HSLATM::[<IO Manager/Slot Number>]-[<HSL ATM Channel/Channel Number>]:[CTAG];
::[<IO Manager/Slot Number>]-[<HSL ATM Channel/Channel Number>]:<CHANNEL_NUMBER=int>,<CLLI=string>,<PORT=PortNumber>,<VPI=int>,<VCI=int>,<SCRAMBLING=EnableType>,<HEC_POLY=EnableType>,<HEC_VERIF=CheckLevel>,<QOS=BitRate>,<STATE=FuncStatus>,<L3U=ChannelStatus>,<DBG=string>,<T1=int>,<T2=int>,<T3=int>,<ALIGNMENT=Align>,<N1=int>,<CNGS_LVL1_ONST=int>,<CNGS_LVL2_ONST=int>,<CNGS_LVL3_ONST=int>,<CNGS_LVL1_ABT=int>,<CNGS_LVL2_ABT=int>,<CNGS_LVL3_ABT=int>,<LOGL1=LoggingState>,<LOGL2=LoggingState>,<LOGL3=LoggingState>,<LOGL4=LoggingState>;
AID Description
Channel Number - Position 1
Type: int
Description: Number that is used in communication with Level 3
Attribute Details
CHANNEL_NUMBER - Channel Number
Type: int
Description: Number that is used in communication with Level 3
CLLI - CLLI
Permission: Writeable
Type: string
Description: Common Language Location Identifier string for this channel.
PORT - Port
Permission: Createable
Type: PortNumber={PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,NOT_CONFIGURED,PORT_8}
Description: The number of the I/O port with the physical connection to the link
VPI - VPI
Permission: Writeable
Type: int
Description: Virtual path identifier (0-255)
VCI - VCI
Permission: Writeable
Type: int
Description: Virtual channel identifier (0-65535)
SCRAMBLING - Scrambling
Permission: Writeable
Type: EnableType={DISABLED,ENABLED}
Description: Scrambling of the payload part of the ATM cell
HEC_POLY - HEC Polynomial
Permission: Writeable
Type: EnableType={DISABLED,ENABLED}
Description: Also called coset, HEC ATM polynomial option used in HEC calculation
HEC_VERIF - HEC Verification
Permission: Writeable
Type: CheckLevel={FILTER,CORRECT}
Description: Filter or correct cells received with invalid HEC
QOS - Quality of Service
Permission: Writeable
Type: BitRate={CBR,rt-VBR,nrt-VBR,UBR}
Description: Constant, rt-aVerage, nrt-aVerage, Unspecified
STATE - Channel State
Permission: Read-only
Type: FuncStatus={ACTIVATED,DEACTIVATED,FAILED}
Description: Link Manager state
L3U - L3 Use
Permission: Read-only
Type: ChannelStatus={IN_USE,AVAILABLE, 1 to 1024}
Description: Either the assigned Server Process number or AVAILABLE if not registered.
DBG - Debug
Permission: Read-only
Type: string
Description: Information for support purposes.
T1 - T1
Permission: Writeable
Type: int
Description: T1 Timer. Time in ms between link release and re-establishment during alignment
T2 - T2
Permission: Writeable
Type: int
Description: T2 Timer. Time in ms that SSCF will attempt link alignment
T3 - T3
Permission: Writeable
Type: int
Description: T3 Timer. Time in ms between proving PDUs
ALIGNMENT - Alignment
Permission: Writeable
Type: Align={NORMAL,EMERGENCY}
Description: Alignment type
N1 - N1
Permission: Writeable
Type: int
Description: Number of PDUs sent during normal proving
CNGS_LVL1_ONST - Congestion Level 1 Onset
Permission: Writeable
Type: int
Description: Onset of level 1 congestion for ANSI and Onset of congestion for ITU. In ITU any congestion level will trigger notice to L3.
CNGS_LVL2_ONST - Congestion Level 2 Onset
Permission: Writeable
Type: int
Description: Onset of level 2 congestion for ANSI. In ITU any congestion level will trigger notice to L3.
CNGS_LVL3_ONST - Congestion Level 3 Onset
Permission: Writeable
Type: int
Description: Onset of level 3 congestion for ANSI. In ITU any congestion level will trigger notice to L3.
CNGS_LVL1_ABT - Congestion Level 1 Abate
Permission: Writeable
Type: int
Description: Level 1 congestion abatement for ANSI and congestion abatement for ITU. In ITU the lowest abatement the clear notice trigger for L3.
CNGS_LVL2_ABT - Congestion Level 2 Abate
Permission: Writeable
Type: int
Description: Level 2 congestion abatement for ANSI. In ITU the lowest abatement the clear notice trigger for L3.
CNGS_LVL3_ABT - Congestion Level 3 Abate
Permission: Writeable
Type: int
Description: Level 3 congestion abatement for ANSI. In ITU the lowest abatement the clear notice trigger for L3.
LOGL1 - Management
Permission: Writeable
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Minimal logging - mostly exchanges with level 3.
LOGL2 - SSCF Messages
Permission: Writeable
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: High level state transitions. Few logs during normal operations.
LOGL3 - SSCOP Messages
Permission: Writeable
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Verbose logging of protocol events. Not for production environment.
LOGL4 - PDUs
Permission: Writeable
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Very verbose logging or each message. Not for production environment.
HSL ATM Channel
VFY-IOCH-HSLATMDBG
VFY-IOCH-HSLATMDBG::[<IO Manager/Slot Number>]-[<HSL ATM Channel/Channel Number>]:[CTAG];
::[<IO Manager/Slot Number>]-[<HSL ATM Channel/Channel Number>]:<SSCOP_STATE=string>,<SSCF_STATE=string>;
Attribute Details
SSCOP_STATE - SSCOP State
Permissions: Read-only
Type: string
Description: .
SSCF_STATE - SSCF State
Permissions: Read-only
Type: string
Description: .
Port Clocking
CHG-IO-PORTCLOCK
CHG-IO-PORTCLOCK::[<IO Manager/Slot Number>]:[CTAG]:::::[PRMCLKSRC=<ClockSource>],[SECCLKSRC=<ClockSource>],[CLKMODE=<ClockMode>];
VFY-IO-PORTCLOCK
VFY-IO-PORTCLOCK::[<IO Manager/Slot Number>]:[CTAG];
::[<IO Manager/Slot Number>]:<INDVPRTCLK=EnableType>,<PRMCLKSRC=ClockSource>,<SECCLKSRC=ClockSource>,<CURCLKSRC=ClockSource>,<CLKMODE=ClockMode>;
Attribute Details
INDVPRTCLK - Per-Port Clocking
Permission: Read-only
Type: EnableType={DISABLED,ENABLED}
Description: If ENABLED all ports can be configured to maintain separate clocking sources, otherwise there is a single clocking source for all ports. (hardware dependent)
PRMCLKSRC - Primary Clock Source
Permission: Writeable
Type: ClockSource={NONE,INTERNAL,PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,CLOCK_A,CLOCK_B,PORT_8,TELCO_A,TELCO_B}
Description: Primary Clock source
SECCLKSRC - Secondary Clock Source
Permission: Writeable
Type: ClockSource={NONE,INTERNAL,PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,CLOCK_A,CLOCK_B,PORT_8,TELCO_A,TELCO_B}
Description: Secondary Clock source
CURCLKSRC - Current Clock Source
Permission: Read-only
Type: ClockSource={NONE,INTERNAL,PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,CLOCK_A,CLOCK_B,PORT_8,TELCO_A,TELCO_B}
Description: Current clock source
CLKMODE - Clock Mode
Permission: Writeable
Type: ClockMode={STAND_ALONE,SLAVE,MASTER_A,MASTER_B,MASTER_TELCO_A,MASTER_TELCO_B}
Description: Clock mode for H110 enabled devices
Port Configuration
CHG-IO-PORT
CHG-IO-PORT::[<IO Manager/Slot Number>]-[<Port/Port Number>]:[CTAG]:::::[CLKSRC=<IndvPortClockSrc>],[IF_TYPE=<LineType>],[ENCODING=<Encoding>],[LINE_LENGTH=<LineLength>],[FDL=<EnableType>],[ALM_SQUELCH=<EnableType>],[ALM_EGRESS=<AlarmType>],[LPBK_MODE=<Loopback>],[STATISTICS=<LoggingState>],[STATUS_ALARMS=<Alarming>],[BERT_LOOPTYPE=<FarEndLoopback>],[BERT_LOOPACT_TIME=<int>],[BERT_LOOPDEACT_TIME=<int>],[BERT_PATTERN=<BERTPattern>],[PRBS_DET_TIME=<int>],[BERT_DURATION=<int>];
VFY-IO-PORT
VFY-IO-PORT::[<IO Manager/Slot Number>]-[<Port/Port Number>]:[CTAG];
SET-IO-PORT
SET-IO-PORT::[<IO Manager/Slot Number>]-[<Port/Port Number>]:[CTAG]:::[START_BERT/STOP_BERT/SEND_LOOP_UP/SEND_LOOP_DOWN/START_PRBS/STOP_PRBS];
::[<IO Manager/Slot Number>]-[<Port/Port Number>]:<PORT=PortNumber>,<CLKSRC=IndvPortClockSrc>,<IF_TYPE=LineType>,<ENCODING=Encoding>,<LINE_LENGTH=LineLength>,<FDL=EnableType>,<ALM_SQUELCH=EnableType>,<ALM_EGRESS=AlarmType>,<LPBK_MODE=Loopback>,<STATISTICS=LoggingState>,<STATUS_ALARMS=Alarming>,<FRAMING_STATUS=FramingStatus>,<NO_ALARM=StatusFlag>,<REMOTE_RX_LOF=StatusFlag>,<REMOTE_TX_LOF=StatusFlag>,<RX_AIS=StatusFlag>,<TX_AIS=StatusFlag>,<LOF=StatusFlag>,<LOS=StatusFlag>,<LPBK_STATE=StatusFlag>,<T16_AIS=StatusFlag>,<REMOTE_RX_LOMF=StatusFlag>,<REMOTE_TX_LOMF=StatusFlag>,<RX_TESTCODE=StatusFlag>,<OTHER_FAILURE=StatusFlag>,<UNAV_SIGSTATE=StatusFlag>,<NE_OOS=StatusFlag>,<RX_PAYLOAD_AIS=StatusFlag>,<PERF_TH=StatusFlag>,<NO_LPBK=StatusFlag>,<REMOTE_P_LPBK=StatusFlag>,<REMOTE_L_LPBK=StatusFlag>,<LOCAL_L_LPBK=StatusFlag>,<FE_P_LPBK=StatusFlag>,<FE_L_LPBK=StatusFlag>,<CUR_GAIN=int>,<CUR_ATTEN=int>,<BERT_LOOPTYPE=FarEndLoopback>,<BERT_LOOPACT_TIME=int>,<BERT_LOOPDEACT_TIME=int>,<BERT_PATTERN=BERTPattern>,<PRBS_DET_TIME=int>,<BERT_DURATION=int>,<BERT_STATUS=string>,<BERT_RESULT=string>,<PRBS_SYNC_SEC=int>,<PRBS_LOST_SEC=int>,<PRBS_BIT_ERRORS=int>,<PRBS_ERROR_INSTS=int>;
AID Description
Port Number - Position 1
Type: PortNumber={PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,NOT_CONFIGURED,PORT_8}
Description: Port number as indicated on physical device.
Attribute Details
PORT_NUMBER - Port Number
Permission: Read-only
Type: PortNumber={PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,NOT_CONFIGURED,PORT_8}
Description: Port number as indicated on physical device.
CLKSRC - Clock Source
Permissions: Writeable
Type: IndvPortClockSrc={THROUGH,RECOVERED}
Description: Port specific clock source. THROUGH clocking uses on board clock. RECOVERED clocking loops the received clock back out. Availability is hardware dependent.
IF_TYPE - Interface Type
Permissions: Writeable
Type: LineType={J1,T1_ESF,T1_D4,E1,E1_CRC4}
Description: Interface type for the port (J1, T1_ESF, T1_D4, E1, E1_CRC4)
ENCODING - Encoding
Permissions: Writeable
Type: Encoding={B8ZS,HDB3,AMI}
Description: Line Encoding mode (B8ZS, HDB3, AMI)
LINE_LENGTH - Line Length
Permissions: Writeable
Type: LineLength={E1_75_OHM_SHORTHAUL,E1_120_OHM_SHORTHAUL,E1_75_OHM_LONGHAUL,E1_120_OHM_LONGHAUL,T1_SHORTHAUL_0_133FT,T1_SHORTHAUL_133_266FT,T1_SHORTHAUL_266_399FT,T1_SHORTHAUL_399_533FT,T1_SHORTHAUL_533_655FT,T1_LONGHAUL_0db,T1_LONGHAUL_7db,T1_LONGHAUL_15db,T1_LONGHAUL_22db,J1_SHORTHAUL,J1_LONGHAUL}
Description: Transmit buildout for interface type.
FDL - Facility Data Link
Permissions: Writeable
Type: EnableType={DISABLED,ENABLED}
Description: Facility DataLink (FDL) is only applicable for T1_ESF interface type
ALM_SQUELCH - Alarm Squelch
Permissions: Writeable
Type: EnableType={DISABLED,ENABLED}
Description: Stop responding to received alarms
ALM_EGRESS - Alarm Egress
Permissions: Writeable
Type: AlarmType={RAI,AIS}
Description: Type of alarm to transmit on reception of AIS (red alarm) (RAI, AIS)
LPBK_MODE - Loopback Mode
Permissions: Writeable
Type: Loopback={DISABLED,REMOTE_PAYLOAD,REMOTE_LINE,LOCAL_LINE}
Description: Loopback mode (DISABLED, REMOTE_PAYLOAD, REMOTE_LINE, LOCAL_LINE)
STATISTICS - Statistics
Permissions: Writeable
Type: LoggingState={NOT_LOGGED,LOGGED,OVERRIDDEN}
Description: Log port statistics to the debug log every 15 minutes.
STATUS_ALARMS - Status Alarms
Permissions: Writeable
Type: Alarming={DISABLED,ENABLED}
Description: When enabled, MTP2 will alarm on major and critical port status events. Only one critical and one major alarm is raised per port regardless of the number of current critical and major events. These traps are displayed in the dash board and sent to SNMP trap hosts. Alarm 5818 is for major port status events and alarm 5820 indicates critical port status events.
FRAMING_STATUS - Framing Status
Permissions: Read-only
Type: FramingStatus={NA,NOSYNC,SYNC}
Description: Framing Status (SYNC, NOSYNC)
NO_ALARM - No Alarm
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: None of the defined alarms are present
REMOTE_RX_LOF - Remote Rx LOF
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Remote Receiver Loss of Frame
REMOTE_TX_LOF - Remote Tx LOF
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Remote Transmitter Loss of Frame
RX_AIS - Rx AIS
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Receiver Alarm Indication Signal
TX_AIS - Tx AIS
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Transmitter Alarm Indication Signal
LOF - Loss of Frame
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Local Loss of Frame
LOS - Loss of Synchronization
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Local Loss of Synchronization
LPBK_STATE - Loopback State
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Loopback State On/Off
T16_AIS - T16 AIS
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Timeslot 16 AIS Clear/Set
REMOTE_RX_LOMF - Remote Rx LOMF
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Remote Receiver Loss of Multiframe
REMOTE_TX_LOMF - Remote Tx LOMF
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Remote Transmitter Loss of Multiframe
RX_TESTCODE - Rx Test Code
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Receiver Test Code On/Off
OTHER_FAILURE - Other Failure
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Other Failure Detected
UNAV_SIGSTATE - Unavailable Signal State
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Unavailable Signal State
NE_OOS - Net Equipment OOS
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Network Equipment Out Of Service
RX_PAYLOAD_AIS - Rx Payload AIS
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Receiver Payload Alarm Indication Signal
PERF_TH - Performance Threshold
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Performance Threshold
NO_LPBK - No Loopback
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: None of the defined Loopback types are present
REMOTE_P_LPBK - Remote Payload Loopback
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Remote Payload Loopback Status
REMOTE_L_LPBK - Remote Line Loopback
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Remote Line Loopback Status
LOCAL_L_LPBK - Local Line Loopback
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Local Line Loopback Status
FE_P_LPBK - Far End Payload Loopback
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Far End Payload Loopback Status
FE_L_LPBK - Far End Line Loopback
Permissions: Read-only
Type: StatusFlag={CLEAR,SET,NA}
Description: Far End Line Loopback
CUR_GAIN - Current Gain
Permissions: Read-only
Type: int
Description: The current gain settings in dbs
CUR_ATTEN - Current Attenuation
Permissions: Read-only
Type: int
Description: The current attenuation in dbs
BERT_LOOPTYPE - Far End Loopback Type
Permissions: Writeable
Type: FarEndLoopback={NONE,LINE,PAYLOAD}
Description: This attribute determines the type of loopback code to send to the far end. Transmission of loopback code is only supported for T1. PAYLOAD loopback code is only available if Facility Data Link is ENABLED. The default value for T1 is LINE, NONE otherwise.
BERT_LOOPACT_TIME - Far End Loopback Activation Time
Permissions: Writeable
Type: int
Description: The amount of time to transmit the loopback activation code. This attribute has no effect if Loopback Type is NONE. If Facility Data Link is ENABLED for T1 ESF, the timer value is in milliseconds and valid values are 40 to 1000 ms. The default value is 100 ms. If Facility Data Link is DISABLED, the timer value is in seconds and valid values are 5 to 10 sec. The default value is 6 sec.
BERT_LOOPDEACT_TIME - Far End Loopback Deactivation Time
Permissions: Writeable
Type: int
Description: The amount of time to transmit the loopback deactivation code. This attribute has no effect if Loopback Type is NONE. If Facility Data Link is ENABLED for T1 ESF, the timer value is in milliseconds and valid values are 40 to 1000 ms. The default value is 100 ms. If Facility Data Link is DISABLED, the timer value is in seconds and valid values are 5 to 10 sec. The default value is 6 sec.
BERT_PATTERN - BERT Pattern
Permissions: Writeable
Type: BERTPattern={User Data,PRBS 2_15}
Description: The type of test data to use for BERT. User Data will inhibit the generation and detection of PRBS test data. PRBS 2_15 will generate 2^15-1 PRBS, non-inverted for T1 and J1, inverted for E1. The default value is PRBS_2_15.
PRBS_DET_TIME - PRBS Detection Timer
Permissions: Writeable
Type: int
Description: The time limit to wait for PRBS detection in the receive stream. This attribute has no effect if BERT Pattern is User Data. Valid values are 0 and 1 to 30 seconds. If the value is 0, the timer is disabled and BERT Duration time begins immediately. The default value is 5 seconds.
BERT_DURATION - BERT Duration
Permissions: Writeable
Type: int
Description: The length of time to perform BERT. The time period begins when PRBS detection is confirmed. Valid values are 0 and 5-3600 seconds. If the value is 0, the timer is disabled and BERT runs indefinitely. The default value is 10 seconds.
BERT_STATUS - BERT Status
Permissions: Read-only
Type: string
Description: Displays state information on BERT state machines. BERT indicates the overall BERT state machine initiated by the Start BERT action. * IDLE - The BERT state machine is not active. * SEND_ACT - BERT has asked LOOP to send loopback activation code. * WAIT_SYNC - BERT is waiting for PRBS to synchronize. * ACTIVE - The main testing cycle is in progress. * SEND_DEACT - BERT has asked LOOP to send loopback deactivation code. * BLOCKED - LOOP or PRBS has been activated independently of BERT. The Start BERT action is prohibited until LOOP and PRBS are both IDLE. LOOP indicates the far end loopback state machine, initiated by the Send Loop Up, Send Loop Down actions, or indirectly by the Start BERT action. * IDLE - The LOOP state machine is not active. * SEND_ACT - LOOP is sending loopback activation code. * ACTIVE - LOOP expects that the far end is in loopback mode due to the sent activation code. * SEND_DEACT - LOOP is sending loopback deactivation code. PRBS indicates the PRBS state machine, initiated by the Start PRBS action, or indirectly by the Start BERT action. * IDLE - The PRBS state machine is not active. * INIT - PRBS has been started and is in a 1 second debounce period to allow the hardware to synchronize. Errors are ignored during this time. * WAIT_SYNC - PRBS is waiting for synchronization. * ACTIVE_SYNC - PRBS is active in test mode, currently synchronized. * ACTIVE_LOST - PRBS is active in test mode, currently not synchronization. Note that when any one of the state machine is not in IDLE state, port configuration attributes Framing, Encoding, and Facility Data Link are locked.
BERT_RESULT - BERT Result
Permissions: Read-only
Type: string
Description: Displays execution results on the last BERT action.
PRBS_SYNC_SEC - PRBS Sync Seconds
Permissions: Read-only
Type: int
Description: Displays number of seconds where PRBS is synchronized during BERT. This indicates the amount of time the PRBS state machine is in the ACTIVE_SYNC state.
PRBS_LOST_SEC - PRBS Lost Seconds
Permissions: Read-only
Type: int
Description: Displays number of seconds where PRBS is unsynchronized during BERT. This indicates the amount of time the PRBS state machine is in the ACTIVE_LOST state.
PRBS_BIT_ERRORS - PRBS Bit Errors
Permissions: Read-only
Type: int
Description: Displays number of bit errors detection while running PRBS. Note that the number of error may be larger than actual, especially in cases of timing slips.
PRBS_ERROR_INSTS - PRBS Error Instances
Permissions: Read-only
Type: int
Description: Displays number of instances where errors were detected while running PRBS. A regular increment of this value may indicate a TDM timing issue.
STATUS_ALARMS - Status Alarms
Permissions: Writeable
Type: Alarming={DISABLED,ENABLED}
Description: When enabled, MTP2 will alarm on major and critical port status events. Only one critical and one major alarm is raised per port regardless of the number of current critical and major events. These traps are displayed in the dash board and sent to SNMP trap hosts. Alarm 5818 is for major port status events and alarm 5820 indicates critical port status events.
Voice Passthrough
SET-IO-VPT
SET-IO-VPT::[<IO Manager/Slot Number>]:[CTAG]:::[CLR_MAP];
VFY-IO-VPT
VFY-IO-VPT::[<IO Manager/Slot Number>]:[CTAG];
::[<IO Manager/Slot Number>]:;
Attribute Details
None.
Local Passthrough
DLT-IO-LPT
DLT-IO-LPT::[<IO Manager/Slot Number>]-[<Local Pass Through/InstanceID>]:[CTAG];
ADD-IO-LPT
ADD-IO-LPT::[<IO Manager/Slot Number>]-[<Local Pass Through/InstanceID>]:[CTAG];
CHG-IO-LPT
CHG-IO-LPT::[<IO Manager/Slot Number>]-[<Local Pass Through/InstanceID>]:[CTAG]:::::[PORT_A=<PortNumber>],[TIMESLOT_A=<Timeslot>],[PORT_B=<PortNumber>],[TIMESLOT_B=<Timeslot>];
VFY-IO-LPT
VFY-IO-LPT::[<IO Manager/Slot Number>]-[<Local Pass Through/InstanceID>]:[CTAG];
::[<IO Manager/Slot Number>]-[<Local Pass Through/InstanceID>]:<ID=int>,<PORT_A=PortNumber>,<TIMESLOT_A=Timeslot>,<PORT_B=PortNumber>,<TIMESLOT_B=Timeslot>;
AID Description
InstanceID (Local Pass Through) - Position 1
Type: int
Description: Object instance number
Attribute Details
ID - InstanceID
Permissions: Read-only
Type: int
Description: Object instance number.
PORT_A - Port A
Permission: Writeable
Type: PortNumber={PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,NOT_CONFIGURED,PORT_8}
Description: Port A receive/transmit
TIMESLOT_A - Time Slot A
Permission: Writeable
Type: Timeslot={NOT_CONFIGURED, 1 to 31}
Description: Time slot on port A
PORT_B - Port B
Permission: Writeable
Type: PortNumber={PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,NOT_CONFIGURED,PORT_8}
Description: Port B receive/transmit
TIMESLOT_B - Time Slot B
Permission: Writeable
Type: Timeslot={NOT_CONFIGURED, 1 to 31}
Description: Time slot on port B
H.110 Passthrough
DLT-IO-HPT
DLT-IO-HPT::[<IO Manager/Slot Number>]-[<H110 Pass Through/InstanceID>]:[CTAG];
ADD-IO-HPT
ADD-IO-HPT::[<IO Manager/Slot Number>]-[<H110 Pass Through/InstanceID>]:[CTAG];
CHG-IO-HPT
CHG-IO-HPT::[<IO Manager/Slot Number>]-[<H110 Pass Through/InstanceID>]:[CTAG]:::::[PORT_A=<PortNumber>],[TIMESLOT_A=<Timeslot>],[CTBUS_TS_RX=<CTBusTS>],[CTBUS_TS_TX=<CTBusTS>];
VFY-IO-HPT
VFY-IO-HPT::[<IO Manager/Slot Number>]-[<H110 Pass Through/InstanceID>]:[CTAG]::::::[<searchedAttrKey1=Value1>][,<searchedAttrKey2=Value2>]…[,<searchedAttrKeyN=ValueN>];
::[<IO Manager/Slot Number>]-[<H110 Pass Through/InstanceID>]:<PORT_A=PortNumber>,<TIMESLOT_A=Timeslot>,<CTBUS_TS_RX=CTBusTS>,<CTBUS_TS_TX=CTBusTS>;
AID Description
InstanceID - Position 1
Type: int
Description: Object instance number
Attribute Details
PORT_A - Port A
Permission: Writeable
Type: PortNumber={PORT_0,PORT_1,PORT_2,PORT_3,PORT_4,PORT_5,PORT_6,PORT_7,MONITOR_PORT,NOT_CONFIGURED,PORT_8}
Description: Port A receive/transmit
TIMESLOT_A - Time Slot A
Permission: Writeable
Type: Timeslot={NOT_CONFIGURED, 1 to 31}
Description: Time slot on port A
CTBUS_TS_RX - CTBus Time Slot Rx
Permission: Writeable
Type: CTBusTS={NOT_CONFIGURED, 1 to 4096}
Description: Receive timeslot on the CTBus (1-4096)
CTBUS_TS_TX - CTBus Time Slot Tx
Permission: Writeable
Type: CTBusTS={NOT_CONFIGURED, 1 to 4096}
Description: Transmit timeslot on the CTBus (1-4096)
SCTP Server
VFY-IO-SCTPSRV
VFY-IO-SCTPSRV::[<IO Manager/Slot Number>]:[CTAG];
CHG-IO-SCTPSRV
CHG-IO-SCTPSRV::[<IO Manager/Slot Number>]:[CTAG]:::::[PRIM_IP=<string>],[SEC_IP=<string>],[DBG_LVL=<int>],[HB=<EnableType>],[HB_INV=<int>],[RTO_INIT=<int>],[RTO_MIN=<int>],[RTO_MAX=<int>],[MX_PATH_RETRANS=<int>],[MX_ASSOC_RETRANS=<int>],[BUNDLING=<EnableType>],[BUNDLING_TO=<int>],[DELAYACK_TO=<int>],[FAST_RETRANS_TH=<int>],[CHECKSUM=<SctpChecksumType>];
::[<IO Manager/Slot Number>]:<PROTO=ProtoServed>,<LISTENING_PORT=int>,<PRIM_IP=string>,<SEC_IP=string>,<NUM_ASSOC=int>,<DBG_LVL=int>,<HB=EnableType>,<HB_INV=int>,<RTO_INIT=int>,<RTO_MIN=int>,<RTO_MAX=int>,<MX_PATH_RETRANS=int>,<MX_ASSOC_RETRANS=int>,<BUNDLING=EnableType>,<BUNDLING_TO=int>,<DELAYACK_TO=int>,<FAST_RETRANS_TH=int>,<CHECKSUM=SctpChecksumType>;
Attribute Details
PROTO - Protocol
Permissions: Read-only
Type: ProtoServed={TDM,ATM,ALL}
Description: Which protocols the connections to this server support
LISTENING_PORT - Listening Port
Permissions: Read-only
Type: int(Range: [1024..2.14748e+09])
Description: Port on which SCTP Server listens
PRIM_IP - Primary IP
Permissions: Writeable
Type: string
Description: Primary IP path to listen on
SEC_IP - Secondary IP
Permissions: Writeable
Type: string
Description: Secondary IP path to listen on
NUM_ASSOC - Number of assoc
Permissions: Read-only
Type: int(Range: [0..2.14748e+09])
Description: Number of associations to this server
DBG_LVL - Debug Level
Permissions: Writeable
Type: int(Range: [0..5])
Description: Default Debug level (0-5) of SCTP associations and SCTP Server (0=none, 1=min, 5=max)
HB - Heart Beat
Permissions: Writeable
Type: EnableType={DISABLED,ENABLED}
Description: Heartbeat: periodic sending of test message
HB_INV - Heart Beat Interval
Permissions: Writeable
Type: int(Range: [0..2.14748e+09])
Description: Time between heartbeat messages (ms)
RTO_INIT - RTO Initial
Permissions: Writeable
Type: int(Range: [0..2.14748e+09])
Description: Initial Retransmission Timeout interval when connecting to a remote node
RTO_MIN - RTO Minimum
Permissions: Writeable
Type: int(Range: [0..2.14748e+09])
Description: Minimum Retransmission Timeout interval when communicating to a remote node
RTO_MAX - RTO Maximum
Permissions: Writeable
Type: int(Range: [0..2.14748e+09])
Description: Maximum Retransmission Timeout interval when communicating to a remote node
MX_PATH_RETRANS - Maximum Path Retrans
Permissions: Writeable
Type: int(Range: [0..2.14748e+09])
Description: Number of failed retransmission attempts over current transmission path before deeming the path as unavailable and selecting a different transmission path
MX_ASSOC_RETRANS - Maximum Assoc Retrans
Permissions: Writeable
Type: int(Range: [0..2.14748e+09])
Description: Number of failed retransmission attempts over all transmission paths before deeming the remote node as unavailable
BUNDLING - Bundling
Permissions: Writeable
Type: EnableType={DISABLED,ENABLED}
Description: Bundling of messages into larger packets when possible
BUNDLING_TO - Bundling TO
Permissions: Writeable
Type: int(Range: [0..2.14748e+09])
Description: Length of time messages are queued before bundled into larger packets and transmitted, if bundling is enabled (ms)
DELAYACK_TO - Delayed Ack TO
Permissions: Writeable
Type: int(Range: [0..2.14748e+09])
Description: Length of time to delay acknowledgements to received data
FAST_RETRANS_TH - Fast Retrans Threshold
Permissions: Writeable
Type: int(Range: [0..2.14748e+09])
Description: Number of times a packet can be reported as missing before resending packets using the Fast-Retransmit algorithm
CHECKSUM - Checksum
Permissions: Writeable
Type: SctpChecksumType={CRC32,ADLER32,NONE,PROBE}
Description: Checksum algorithm to be used (CRC32, ADLER32, NONE)
SCTP Association
VFY-IO-SCTPASS
VFY-IO-SCTPASS::[<IO Manager/Slot Number>]-[<SCTP Association/ASP ID>]:[CTAG];
CHG-IO-SCTPASS
CHG-IO-SCTPASS::[<IO Manager/Slot Number>]-[<SCTP Association/ASP ID>]:[CTAG]:::::[DBG_LVL=<int>];
::[<IO Manager/Slot Number>]-[<SCTP Association/ASP ID>]:<ASP_ID=int>,<ASSOC_NUM=int>,<REMOTE_IP1=string>,<REMOTE_IP2=string>,<REMOTE_PORT=int>,<ASSOC_STATUS=SCTPConnStatus>,<DBG_LVL=int>;
AID Description
ASP ID - Position 1
Type: int
Description: Object instance number
Attribute Details
ASP_ID - ASP ID
Permissions: Read-only
Type: int
Description: Object instance number
ASSOC_NUM - Association Number
Permissions: Read-only
Type: int(Range: [0..2.14748e+09])
Description: Number assigned to this SCTP Association
REMOTE_IP1 - Remote IP 1
Permissions: Read-only
Type: string
Description: Remote IP No.1 of this association
REMOTE_IP2 - Remote IP 2
Permissions: Read-only
Type: string
Description: Remote IP No.2 of this association
REMOTE_PORT - Remote Port
Permissions: Read-only
Type: int
Description: Remote port number used for this association
ASSOC_STATUS - Association Status
Permissions: Read-only
Type: SCTPConnStatus={CLOSED,CONNECTING,ESTABLISHED,DEACTIVATED}
Description: Current status of this association
DBG_LVL - Debug Level
Permissions: Writeable
Type: int(Range: [0..5])
Description: Debug level (0-5) of this SCTP association (0=none, 1=min, 5=max)
TIPC Server
VFY-IO-TIPCSRV
VFY-IO-TIPCSRV::[<IO Manager/Slot Number>]-[<TIPC Server/Service Instance>]:[CTAG];
::[<IO Manager/Slot Number>]-[<TIPC Server/Service Instance>]:<PROTO=ProtoServed>,<TIPC_CLASS=int>,<SRVC_NUM=int>,<NUM_ASP=int>;
AID Description
Service Instance - Position 1
Type: int
Description: TIPC service instance number
Attribute Details
PROTO - Protocol
Permissions: Read-only
Type: ProtoServed={TDM,ATM,ALL}
Description: Which protocols the connections to this server will support
TIPC_CLASS - Service Type
Permissions: Read-only
Type: int
Description: TIPC service type number
SRVC_NUM - Service Instance
Permissions: Read-only
Type: int
Description: TIPC service instance number
NUM_ASP - Number of ASP
Permissions: Read-only
Type: int(Range: [0..2.14748e+09])
Description: Number of associations spawned by this server
TIPC Server Process
VFY-IO-TIPCSRVPROC
VFY-IO-TIPCSRVPROC::[<IO Manager/Slot Number>]-[<TIPC Server/Service Instance>]-[<TIPC Server Process/ASP ID>]:[CTAG];
::[<IO Manager/Slot Number>]-[<TIPC Server/Service Instance>]-[<TIPC Server Process/ASP ID>]:<ASP_ID=int>;
AID DESCRIPTION
ASP ID - Position 1
Type: int
Description: Unique number for this connection
Attribute Details
ASP_ID - ASP ID
Permissions: Read-only
Type: int
Description: Unique number for this connection
TCP Server
VFY-IO-TCPSRV
VFY-IO-TCPSRV::[<IO Manager/Slot Number>]:[CTAG];
::[<IO Manager/Slot Number>]:<LISTENING_PORT=int>,<NUM_CONNECTIONS=int>;
Attribute Details
LISTENING_PORT - Listening on Port
Permissions: Read-only
Type: int(Range: [1024..2.14748e+09])
Description: Port on which TCP Server listens
NUM_CONNECTIONS - Number of Connections
Permissions: Read-only
Type: int(Range: [0..2.14748e+09])
Description: Number of connections to this server
TCP Connection
VFY-IO-TCPCX
VFY-IO-TCPCX::[<IO Manager/Slot Number>]-[<TCP Connection/ASP ID>]:[CTAG];
::[<IO Manager/Slot Number>]-[<TCP Connection/ASP ID>]:<TCP_CX=int>,<REMOTE_IP1=string>;
AID DESCRIPTION
ASP ID - Position 1
Type: int
Description: Unique number for this connection
Attribute Details
TCP_CX - ASP ID
Permissions: Read-only
Type: int
Description: Unique number for this connection
REMOTE_IP1 - Remote IP
Permissions: Read-only
Type: string
Description: Remote IP of this connection