Not applicable to
Unable to show "metadata-from": No such page "_space_variables"
or
Unable to show "metadata-from": No such page "_space_variables"
.
The Unable to show "metadata-from": No such page "_space_variables"
includes the Easy Configuration option to add a partially configured signaling group with a new single end-point scenario for ISDN PSTN.
The SBC Easy Configuration interface includes a built-in, step-by-step setup configuration wizard to enable quick and easy deployment of a partially configured signaling group with a new single end-point scenario for ISDN PSTN.
For the single endpoint configuration, since the peer end if not known/configured, in the Easy Configuration Wizard, the Transformation and Routing entries for the endpoint being configured are created independent of the peer end. If you have two endpoints connected and use the Single Leg Wizard to add the third endpoint, you'll need to create/modify the Transformation and Routing entries to complete routing.
Easy Configuration Step 1 includes configuration for scenario parameters.
- In the WebUI, click the Tasks tab.
- In the left navigation panel, go to SBC Easy Setup > Easy Config Wizard.
From the Application drop down list, select ISDN PSTN
Configure per the field definitions below and click Next.
Configure Scenario Parameters - Field Definitions
Field | Description |
---|
Application | Configuration template used: ISDN PSTN. |
Scenario Description | Name to describe the setup. |
Telephone Country | Country in which the ISDN PTSN endpoint is setup. |
Provider Type | Hardcoded to ISDN. |
Easy Configuration Step 2 includes configuration for the ISDN PSTN endpoint.
- Configure the ISDN PSTN information.
- Click Next.
The fields below are displayed if you select
ISDN/PSTN from the
Application drop down list in Step 1.
Configure ISDN PSTN Parameters
Field | Description |
---|
Port Type | Specifies the physical T1/E1 port used for this Signaling Group. Valid option: T1 or E1. |
DS1 Ports | The physical T1/E1 port number to which the PSTN line is physically connected. DS1 entries are configured with the following command buttons: Up (move a DS1 port up in the list), Down (move a DS1 port down in the list), Add (adds a DS1 port), and Remove (deletes a DS1 port). For example, click Add. Select the desired PSTN port and OK. |
Switch Variant | Specifies the ISDN variant for the port type in the ISDN Signaling Group. For T1 - ATT 4EES
- ATT 5EES
- DMS 100
- N12
- Euro ISDN
- QSIG
- Japanese ISDN
For E1: |
ISDN Number Translation | Determines if the SBC should translate dialed PSTN digits as phone extensions. Valid options: Translation Extension (translates digits into phone extensions) or Passthrough Untranslated (does not translate digits). |
PBX Prefix | Numbers to prefix for the translated phone extension. This field is available only when ISDN Number Translation is set to Translation Extension. |
Extension Length | The number of digits used to account for the PSTN extension. Valid options: 2, 3, 4, or 5.This field is available only when ISDN Number Translation is set to Translation Extension. |
Clock Source | Specifies the source of the systems transmit clock. - System: The built-in oscillator is used to transmit data over synchronous links.
- Network: The clock is derived from the data received from the peer devices on the network.
|
Primary Clock Port | Specifies the primary port for the clock source. This field displays only when Network is selected as the Clock Source. |
Secondary Clock Port | Specifies the secondary port for the clock source. This field displays only when Network is selected as the Clock Source. |
ISDN Side | Specifies the ISDN user/network side for this signaling group to be created by this wizard. Valid entries: Network or User. |
Easy Configuration Step 3 includes a summary of the information configured in Step 1 and Step 2.
Review the information and click Finish.
See below for an example: