You are viewing an old version of this page. View the current version.

Compare with Current View Page History

Version 1 Current »

In this section:

Related articles:

Use the Diam Node window to define the parameters for the SBC side of a Diameter interface.

The 

Unable to show "metadata-from": No such page "_space_variables"
 uses a connection over a Diameter interface for both quality of service (QoS) resource reservation requests and for transmitting lawful intercept (LI) information to mediation servers in deployments that follow the PacketCable 2.0 LI model. Within SBC configuration there is a single Diameter node object that is shared for both use cases. 

In the first use case, the Rx interface pertains to QoS resource reservation for reserving bandwidth in an IP access network. The Rx interface is used to exchange application-level session information between a Policy and Charging Rules Function (PCRF) element and the P-CSCF. The SBC, acting as a P-CSCF, creates a TCP connection with the configured PCRF. For this case, you use the Diam Node window to configure the Diameter realm for sending external QoS requests on a per-IP-trunk-group basis.

In the second case, the SBC uses a Diameter-based interface (X2 interface) over TCP transport to send intercepted call data and associated call events from the SBC to an LI mediation server. In general, LI configuration must be completed by a user with specific LI privileges (the calea user). However because the Diameter node object is also used for a non-LI purpose, the name  of the Diameter node must be assigned, as described on this page, by a user with admin privileges. You then include the Diameter node name in the LI call data channel (CDC) configuration. However, the remaining Diameter configuration required to support PC 2.0 LI (Diameter peers and Diameter realm routes), must be completed by the calea user within CDC configuration. Refer to PacketCable 2.0 LI Configuration for more information and to Configure CDC for PacketCable 2.0 (EMS documentation) for procedures for configuring Diameter parameters for PC 2.0 LI deployments.


Note

The SBC 5210 and SBC 7000 systems support creating IP Interface Groups containing sets of IP interfaces that are not "processor friendly" (i.e. carried on physical Ethernet ports served by separate processors). However, restrictions exist regarding the usage of such Interface Groups.

(This ability does not apply to the SBC 5110 and 5400 systems which have only two physical media ports. IP interfaces from the two physical ports may be configured within the same IP Interface Groups without restrictions.)

For complete details, refer to Configuring IP Interface Groups and Interfaces.

Do not configure PCRF on the egress leg of the trunk group for REGISTER.

When configuring the Diameter node in an HA configuration, the Secondary Origin Host parameter must be configured with the Standby hostname

To View Diam Node Configuration

On the

Unable to show "metadata-from": No such page "_space_variables"
 main screen, navigate to All > Address Context > Diam Node.

The Diam Node window opens. In Address Context, select the address context for the Diameter node.

Diam Node Window

To Create the Diam Node

To create the Diam Node:

  1. Click New Diam Node. The Create New Diam Node window opens.

    Create New Diam Node Window

  2. Use the following table to configure the fields and then click Save.

Diam Node Parameters

Parameter

Length/Range

Description

Name

1-23 characters

The name of this Diameter node. If you are configuring the SBC for PC 2.0 LI, use this name in the LI CDC configuration. Refer to Configure CDC for PacketCable 2.0 (EMS documentation) for more information.

Origin Realm

1-128 characters

The origin realm for the node.

Primary Origin Host

1-128 characters

The primary origin host for the node.

Secondary Origin Host

1-128 characters

The secondary origin host for the node.

Transaction Timeout

500-6000

The timeout value in milliseconds, with a default value of 1000.

State

N/A

The state of the Diameter node.

  • Disabled (default)
  • Enabled

Dump Pdu

N/A

When enabled, the SBC logs the DIAMETER PDU sent and received on the Rx interface to the debug log.

  • Disabled (default)
  • Enabled

This option is not applicable if you are using the Diameter node for PC 2.0 LI.

IP Interface Group Name

N/A

The name of the IP Interface group to use.

IP V4Address

N/A

The IPv4 address used to create connections towards a peer.

IP V6Address

N/A

The IPv6 address used to create connections towards a peer.

To Edit the Diam Node

To edit the Diam node configuration:

  1. Click the radio button next to the Diam node name. The Edit Selected Diam Node window opens.
  2. Make any required changes and click Save.

To Delete the Diam Node 

To delete the Diam Node configuration:

  1. Click the radio button next to the Diam node you want to delete.
  2. Click the Delete icon (X) at the end of the row.
  3. Confirm the deletion when prompted.

  • No labels