You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 10 Next »

REST API Method: PUT /rest/medialistprofile/{identifier}

Creates a Media List Profile Table given a specific Table ID.

URL:

https://192.168.0.111/rest/medialistprofile/{identifier}

HTTP Method

PUT

Requires Authentication:

true

medialistprofile - REST API Methods

The root page @parent could not be found in space SBC 1000/2000 API.

Parameters

Parameter Name Required Service Affecting Data Type Default Value Possible Values Description
DescriptionNoNostringnone64 - Max Length Meaningful name for the profile.
VoiceFaxProfileIDYesNostring1200 - Max Length Identifies a comma separated string of the Media Profile IDs to be used in this profile.
CryptoProfileIDNoNoint0Possible values:
  • 0 - Minimum
  • 65534 - Maximum
Identifies a cryto profile ID used. If no crypto profile is used then this is set to 0.
DtlsProfileIDNoNoint0Possible values:
  • 0 - Minimum
  • 65534 - Maximum
Identifies a DTLS profile ID used. If no DTLS profile is used then this is set to 0.
DeadCallDetectionNoNoEnum0Possible values:
  • 0 - edtEnable
  • 1 - edtDisable
To turn on and off the DCD feature based off of RTCP.
DSCPYesNoint46Possible values:
  • 0 - Minimum
  • 63 - Maximum
The DSCP value to be used in the IP header of media packets from the SBC Edge, for calls that use this Media List
ReceiveGainYesNoint0Possible values:
  • -14 - Minimum
  • 6 - Maximum
Specifies the gain or loss in decibels to apply to received signals. Rx gain implies the gain of signal from Packet to PCM side.
TransmitGainYesNoint0Possible values:
  • -14 - Minimum
  • 6 - Maximum
Specifies the gain or loss in decibels to apply to transmitted signals. Tx gain implies the gain of signal from PCM to Packet side.
SilenceSuppressionNoNoEnum0Possible values:
  • 0 - edtEnable
  • 1 - edtDisable
To turn on and off the Voice Activity Detection and send PT13 packets when on.
ComfortNoiseTDMNoNoEnum0Possible values:
  • 0 - edtEnable
  • 1 - edtDisable
 Not used.
DigitRelayTypeYesNoEnum1Possible values:
  • 0 - drtVoice
  • 1 - drtRFC2833
  • 2 - drtSIPInfo
 Specifies the digit relay type to use.
  • RFC 2833
    - When a DTMF digit is detected in the voice stream coming from the TDM side,the digit is removed from the voice stream (going to the IP network),and is sent out-of-band using the RFC 2833 mechanism.
  • As Voice
    - The DTMF digits are sent in the voice stream without any special treatment.
DigitRelayPayloadTypeYesNoint101Possible values:
  • 96 - Minimum
  • 127 - Maximum
 Specifies the payload type used for RFC 2833 packets.

This field is available when Digit (DTMF) Relay Type is set to RFC 2833.

ModemRelayYesNoEnum0Possible values:
  • 0 - edtEnable
  • 1 - edtDisable
Specifies if modem passthrough is enabled when using the G.711 codec.
FaxRelayYesNoEnum0Possible values:
  • 0 - edtEnable
  • 1 - edtDisable
Specifies if fax passthrough is enabled when using the G.711 codec.
CNGToneDetectionYesNoEnum0Possible values:
  • 0 - edtEnable
  • 1 - edtDisable
Specifies if the system should detect fax calling tones. This tone is produced by the origination side fax machine.
CNGNumberOfCyclesYesNoint2Possible values:
  • 1 - Minimum
  • 5 - Maximum
 Specifies the number of cycles that must be detected by the system before it considers the tone to be a valid CNG tone. 1 to 5 are valid values.

This field is available when CNG Tone Detection is enabled.

FAXToneDetectionYesNoEnum1Possible values:
  • 0 - btFalse
  • 1 - btTrue
Specifies if the system should detect fax(V.21 flag) tone. This tone is produced by the terminating side fax machine.
MediaRTCPModeYesNoEnum0Possible values:
  • 0 - rtcptRTCP
  • 1 - rtcptRTCPXR
 Specifies if RTCP-XR packet type can be used in RTCP channel. If XR is chosen make sure the remote end can support XR RTCP frames.
DtmfSignalToNoiseYesNoint0Possible values:
  • -3 - Minimum
  • 6 - Maximum
 Controls the minimum Signal to Noise ratio threshold (in decibels) for the DTMF detector.
DtmfMinimumLevelYesNoint-38Possible values:
  • -48 - Minimum
  • -14 - Maximum
 Controls the minimum level (dBm0) for each of the received DTMF components.

  • No labels