You are viewing an old version of this page. View the current version.

Compare with Current View Page History

Version 1 Current »

In this section:

Zone CAC

Command Syntax

Note

Unless annotated otherwise, the parameter values in this section apply to the SBC Core.

% set addressContext <addressContext_name> zone <zone_name> cac 
	bandwidthLimit <0-2147483647, or unlimited>
	bandwidthLimitThreshold <0-100>
	bandwidthVideoThreshold <0-100>
	callLimit <0-2147483647, or unlimited>
	callLimitThreshold <0-100>
	egress 
	emergencyOversubscription <0-1000>
	extendedEmergencyIpLimit <0-40000>
	hpcOversubscription <0-100>
	ingress
	registrationLimit <0-2147483647, or unlimited>

 

Command Parameters

Zone CAC Parameters

 

Parameter

Length/Range

Description

zone

1-23

The name of the zone. You can configure signaling, media, and control for a zone in the address context.

Zone name is unique across all address contexts.
cacN/A

Call Admission Control (CAC) parameters for all peers using this zone.

bandwidthLimit0-2147483647, or unlimitedTotal bandwidth limit in Kbps/sec.
bandwidthLimitThreshold0-100Bandwidth utilization notification threshold, as a percentage. (default = 0)
bandwidthVideoThreshold0-100

Enter threshold value (as a percentage of video bandwidth) to limit video streams to a specific bandwidth to prevent video calls consuming call bandwidth otherwise needed for audio calls. (default = 0)

callLimit0-2147483647, or unlimitedTotal number of calls allowed on this zone. (default = 'unlimited')
callLimitThreshold0-100Call limit utilization notification threshold, as a percentage. (default = 0)
egressN/AEgress-specific call admission control configuration. See Egress Parameters table below for details.
emergencyOversubscription0-1000, or unlimitedThis parameter gives priority treatment to emergency calls by specifying the resource over-subscription percentage allowed for emergency calls, and represents the allowed percentage of emergency calls beyond the configured call limit. When the call limit is reached, normal calls are rejected but emergency calls are accepted up to an expanded limit. (default = 10)
extendedEmergencyIpLimit0-40000Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0)
hpcOversubscription0-100This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10)

ingress

N/A

Ingress-specific call admission control configuration. See Ingress Parameters table below for details.

registrationLimit0-2147483647, or unlimitedThe number of concurrent registrations allowed in this zone. (default = 'unlimited')

 

Egress

Command Syntax

% set addressContext <addressContext_name> zone <zone_name> egress 
		callBurstMax <1-900, or unlimited> (SBC 7000 range is 1-2700)
		callLimit <0-2147483647, or unlimited>
		callRateMax <1-450, or unlimited> (SBC 7000 range is 1-1350)
		emergencyOversubscription <0-1000>
		extendedEmergencyIpLimit <0-40000>
		hpcOversubscription <0-100>
		registerBurstMax <1-200, or unlimited> (SBC 7000 range is 1-600)
		registerRateMax <1-100, or unlimited> (SBC 7000 range is 1-300)

Command Parameters

Egress Parameters

 
ParameterLength/RangeDescription
callBurstMax

SBC 5000:
1-900, or unlimited.

SBC 7000:
1-2700, or unlimited

Maximum allowed burst (above the allowed sustained rate) for egress call attempts, in calls/second. (default = 'unlimited')
callLimit0-2147483647, or unlimitedTotal number of outbound concurrent calls allowed. (default = 'unlimited' )
callRateMax

SBC 5000:
1-450, or unlimited.

SBC 7000:
1-1350, or unlimited

Maximum sustained egress call rate allowed in calls/second. (default = 'unlimited' )

You can set both callRateMax and callBurstMax as “unlimited”; however, if you assign a value to one parameter, the other must also be assigned a value.
emergencyOversubscription0-1000Over-subscription of resources (as a percentage) allowed for emergency calls. (default = 10)
extendedEmergencyIpLimit0-40000Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0)
hpcOversubscription0-100This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10)
registerBurstMax

SBC 5000:
1-200, or unlimited

SBC 7000:
1-600, or unlimited

Maximum allowed burst (above allowed sustained rate) for egress initial SIP registrations. (default = 'unlimited')

registerRateMax

SBC 5000:
1-100, or unlimited.

SBC 7000:
1-300, or unlimited

Maximum sustained egress rate of initial SIP registrations allowed on this zone. (default = 'unlimited')

You can set both “registerBurstMax” and “registerRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value.

 

Ingress

Command Syntax

% set addressContext <addressContext_name> zone <zone_name> cac ingress 
	callBurstMax <1-900, or unlimited> (SBC 7000 range is 1-2700)
	callLimit <0-2147483647, or unlimited>
	callRateMax <1-450, or unlimited> (SBC 7000 range is 1-1350)
	emergencyOversubscription <0-1000>
	extendedEmergencyIpLimit <0-40000>
	hpcOversubscription <0-100>
	packetRateMax <1-65535, or unlimited>
	registerBurstMax <1-200, or unlimited> (SBC 7000 range is 1-600)
	registerRateMax <1-100, or unlimited> (SBC 7000 range is 1-300)

Command Parameters

 

Ingress Parameters

 
ParameterLength/RangeDescription
callBurstMax

SBC 5000:
1-900, or unlimited.

SBC 7000:
1-2700, or unlimited

Maximum allowed burst (above the allowed sustained rate) for ingress calls, in calls/second. (default = 'unlimited')
callRateMax

SBC 5000:
1-450, or unlimited.

SBC 7000:
1-1350, or unlimited

Maximum sustained ingress call rate allowed in calls/second. (default is 'unlimited')

You can set both callRateMax and callBurstMax as "unlimited"; however, if you assign a value to one parameter, the other must also be assigned a value.
emergencyOversubscription 0-1000Over-subscription of resources (as a percentage) allowed for emergency calls. (default = 10)
extendedEmergencyIpLimit 0-40000Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency over-subscription quota are exhausted. (default = 0)  
hpcOversubscription0-100This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10)
packetRateMax1-65535, or unlimitedMaximum sustained packet rate allowed in packets/second. (default = 'unlimited')
registerBurstMax

SBC 5000:
1-200, or unlimited.

SBC 7000:
1-600, or unlimited

Maximum burst (above the allowed sustained rate) for initial SIP registrations. (default = 'unlimited')
registerRateMax

SBC 5000:
1-100, or unlimited.

SBC 7000:
1-300, or unlimited

Maximum sustained rate of initial SIP registrations   allowed in registrations/second. (default = 'unlimited')

You can set both registerBurstMax and registerRateMax as 'unlimited'; however, if you assign a value to one parameter, the other must also be assigned a value.

 

  • No labels