You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 5 Current »

 

In this section:

Use the GW Sig Port window to configure a signaling port for gateway-to-gateway (GW to GW) call signaling. The gateway-to-gateway signaling is a protocol that transports call signaling messages between SBC (and GSX) instances over a TCP connection and requires that an external PSX is part of the network. The SBC supports gateway-to-gateway signaling on all platforms, including virtualized SBC SWe deployments.

The parameters to define the GW signaling port differ based on your type of the SBC platform. For cloud-based deployments of SBC SWe (I-SBC or D-SBC), the parameters include IP Var so that the IP address for the port can be specified using a metavariable rather than a static IP address. For other SBC platforms, the IP Address V4 or V6 parameter appears for you to enter a specific IP address.

The SBC supports a single GW signaling port at a time. The GW signaling port must be defined within the "default" address context and the "defaultSigZone" zone, and it must be assigned an index value of 1.

 

Note

Each signaling port within an Address Context must use a unique IP address and port number combination.

Note

The SBC 52x0 and SBC 7000 systems support creating IP Interface Groups containing sets of IP interfaces that are not "processor friendly" (i.e. carried on physical Ethernet ports served by separate processors). However, restrictions exist regarding the usage of such Interface Groups.

(This ability does not apply to the SBC 51x0 and SBC 5400 systems which have only two physical media ports. IP interfaces from the two physical ports may be configured within the same IP Interface Groups without restriction.)

For complete details, refer to Configuring IP Interface Groups and Interfaces.

View GW Sig Port

On the SBC main screen, go to Configuration > System Provisioning > Category: Base Provisioning > Signaling Ports > GW Sig Port.

The GW Sig Port window is displayed. The following example shows I-SBC/D-SBC output.

Signaling Ports - Gw Sig Port

 

Create the GW Sig Port

To create a new GWSig Port,

Select "default" from the Address Context drop-down and  "defaultSigZone" from the Zone drop-down.

Click New GW Sig Port button on the GW Sig Port List panel.

Gw Sig Port Fields

The Create New Gw Sig Port window is displayed. The following example shows the parameters for an I-SBC or D-SBC deployment.

Gw Sig Port Create Window

 

The following fields are displayed:

Gw Sig Port Parameters

Parameter

Description

Index

Set the index for gateway signaling port to 1.

Ip Interface Group Name

Specify the name of the IP interface group used by this signaling port.

Ip Address

Specify the IP address for the gateway signaling listening port in IPV4 or IPV6 format.

This is a required parameter visible on hardware systems and SBC SWe systems that do not use metavariables.

Note: For cloud-based I-SBC, D-SBC SBC SWe deployments, this parameter is not visible.

Port Number

The logical port number of the TCP port to use for this connection. Must be 1-65535, default is 2569.

Role

The main role of the signaling port:
• primary(default)—the port that makes gateway signal link connection requests to other

Unable to show "metadata-from": No such page "_space_variables"
, using its IP address as the local address for listening.
• secondary—an alternate port that is used for listening only and cannot be used to establish new gateway signal links.

When no primary port exists, connection requests to other 
Unable to show "metadata-from": No such page "_space_variables"
cannot be issued and calls which require them are disconnected.
When a secondary port is configured to be primary, the previous primary is automatically made secondary.

Mode

The operational state of the Gateway signaling service:
• inService(default)—the signaling port listens for incoming gateway signal link connection requests.
• outofService—the signal port is not available for incoming gateway signal link connection requests and thus cannot be used to create a new gateway signal links to other

Unable to show "metadata-from": No such page "_space_variables"
.

State

The administrative state of this gateway signaling port:
• disabled—Not active
• enabled—Active

IP Var

Specify the metavariable to use to assign an IP address to the gateway signaling port in an I-SBC or D-SBC deployment. .

Note: This parameter is visible for only I-SBC and D-SBC deployments in the SBC SWe.

Edit the GW Sig Port

To edit any of the Gw Sig Ports in the list, click the radio button next to the specific Gw Sig Port name.

Gw Sig Port Highlighted

 

The Edit Selected GW Sig Port window showing the parameters for an I-SBC or D-SBC is displayed below.

Gw Sig Port Edit Window

 

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

Delete the GW Sig Port

To delete any of the created GW Sig Port, click the radio button next to the specific GW Sig Port which you want to delete.

Gw Sig Port Highlighted

Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.

Gw Sig Port Delete Confirmation

Click Yes to remove the specific Gw Sig Port from the list.

  • No labels