You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 5 Next »

{workflow

Unable to render {include} The included page could not be found.

Overview

The Packet Service Profile supports up to four audio encoding entries, or Codecs, using ERE. The 

Unable to show "metadata-from": No such page "_space_variables"
will negotiate a Codec from the list of Codecs allowed in the Packet Service Profile. One example of a negotiation scenario occurs when a call comes into the 
Unable to show "metadata-from": No such page "_space_variables"
from an H.323 peer. The 
Unable to show "metadata-from": No such page "_space_variables"
preferred coding may be G.711, while the H.323 gateway at the far end may prefer G.729A coding because that gateway has limited bandwidth to access the IP network.

In order to properly handle a call compression negotiation such as that described above, it is necessary to examine the codec list on both the local and remote gateway to find one or more codecs that are common to both. The precedence of the resultant codecs is controlled by the local precedence setting, or the precedence of the remote peer. This provisioning directive is provided by the honorRemotePrecedence parameter.

See Packet Service Profile Provisioning Examples for provisioning examples.

Note

The PSX supports configuring up to 12 codecs in the Packet Service Profile and Preferred Packet Service Profile. The SBC supports receiving all 12 codecs from the PSX in the PSP and Preferred PSP. This applies to interworking with an external PSX (Advanced ERE deployment scenario). See Routing and Policy Management for deployment scenario details.

Additionally, the SBC supports up to 12 codecs over Gateway links to SBCs and/or GSXs.

Note

An SBC-POL-RTU license is needed to enable more than four codecs.

Audio Transparency

Unable to show "metadata-from": No such page "_space_variables"
supports audio transparency in relaying unknown attributes and a subset of known attributes, such as rtpmap, fmtp, and T38 fax. The SBC also manages bandwidth for audio streams in pass-through calls. Audio transparency is controlled by the following PSP and Trunk Group parameters/flags.

Packet Service Profile:

  • Enable transcoderFreeTransparency for the session (enable on either of the PSPs)

  • Configure audioTransparency settings

  • Enable/disable reserveBwForPreferredAudioCommonCodec

SIP Trunk Group:

See SBC SIP Transparency Implementation Guide for transparency implementation details.

Granular Control of HD Codec Offer or Answer

Both the

Unable to show "metadata-from": No such page "_space_variables"
ERE and PSX support the following HD codec prioritization granular controls using Packet Service Profile. ERE functionality is described in this section.

  • Prioritization of HD codec over non-HD codec in the offer when the peer supports both HD and NB codecs even if transcoding is required
  • Prioritization of HD codec selection over non-HD codec in the answer
  • Support of Narrowband (NB) codec list only towards a peer supporting HD and NB codec for backward compatibility

The following

Unable to show "metadata-from": No such page "_space_variables"
flags are configurable in the Packet Service Profile configuration to support this feature. 

  • HDCodec Preferred
  • Prefer NBPassthru Over HDTranscode
  • Match Offered Codec Group If Nb Only
  • Force Route PSPOrder

Command Syntax

% set profiles media packetServiceProfile <unique_profile_name> 
	aal1PayloadSize <0-999>
	audioTransparency <unknownCodecBitRate | unknownCodecPacketSize>
	codec <codecEntry1-codecEntry12> <codec> 
	dataCalls 
		initialPlayoutBufferDelay <5-50> 
		packetSize <10 | 20 | 30 | 40> 
		preferredRtpDataPayloadType <0-127>
	dtls
		dtlsCryptoSuiteProfile <profile name>
		dtlsFlags 
			allowDtlsFallback <disable | enable>
			enableDtlsSrtp <disable | enable>
	flags 
		HDCodecPreferred <disable | enable>
		MatchOfferedCodecGroupIfNbOnly <disable | enable>
		digitDetectSendEnabled <disable | enable> 
		disallowDataCalls <disable | enable> 
		dscpPassthrough <disable | enable>
		forceRoutePSPOrder <disable | enable>
		interworkDtmfWithoutTranscoding <disable | enable>
		preferNBPassthruOverHDTranscode <disable | enable>
		reserveBwForPreferredAudioCommonCodec <disable | enable>
		ssrcRandomize <disable | enable>
		useDirectMedia <disable | enable> 	
		validatePeerSupportForDtmfEvents <disable | enable> 
	honorRemotePrecedence <disable | enable> 
	mediaPacketCos <0-7> 
	packetToPacketControl
		codecsAllowedForTranscoding 
			otherLeg <amr | efr | evrc | g711a | g711u | g722 | g726 | g729 | g7221 | g7222 | g7231 | ilbc | opus | t38> 
			thisLeg <amr | efr | evrc | g711a | g711u | g722 | g726 | g729 | g7221 | g7222 | g7231 | ilbc | opus | t38> 
		conditionsInAdditionToNoCommonCodec
			applyFaxToneTreatment <disable | enable>
			different2833PayloadType <disable | enable>
			differentDtmfRelay <disable | enable> 
			differentPacketSize <disable | enable> 
			differentSilenceSuppression <disable | enable> 
			honorAnswerPreference <disable | enable>
			honorOfferPreference <disable | enable> 
		transcode <conditional | determinedByPspForOtherLeg | only | transcoderFreeTransparency>
	peerAbsenceAction <none | peerAbsenceTrap | peerAbsenceTrapAndDisconnect> 
	preferredRtpPayloadTypeForDtmfRelay <0-128> 
	qosValues msrpDscp <0-255>
	rtcpOptions 
		rtcp <disable | enable> 
		packetLossAction <none | packetLossTrap | packetLossTrapAndDisconnect>
		packetLossThreshold <0-32767>
		terminationForPassThrough <disable | enable> 
	secureRtpRtcp 
		cryptoSuiteProfile <profile_name> 
		flags 
			allowFallback <disable | enable>
			allowPassthru <disable | enable>
			enableSrtp <disable | enable> 
			resetEncDecROCOnDecKeyChange <disable | enable>
			resetROCOnKeyChange <disable | enable>
			updateCryptoKeysOnModify <disable | enable>
	sendRoutePSPPrecedence <disable | enable> 
	silenceFactor <0-50> 
	silenceInsertionDescriptor 
		g711SidRtpPayloadType <0-127> 
		heartbeat <disable | enable> 
	t38 
		dataRateManagementType <type1LocalGenerationOfTcf | type2TransferOfTcf> 
		ecm ecmPreferred <disable | enable> 
		lowSpeedNumberOfRedundantPackets <0 | 1 | 2> 
		maxBitRate <2.4Kbits_s | 4.8Kbits_s | 9.6Kbits_s | 14.4Kbits_s> 
		numberOfRedundantPackets <0 | 1 | 2>
		protocolVersion <0 | 3>
	typeOfService <0-255> 
	videoCalls 
		audioOnlyIfVideoIsPrevented <disable | enable>
		codecListProfile <name>
		ieee8021QVLanCos <0-7>
		ipv4Tos <0-255>
		ipv6TrafficClass <0-255>
		maxVideoBandwith <0-50000> 
		videoBandwidthReductionFactor <0-100> 
	voiceInitialPlayoutBufferDelay <1-50> 

Command Parameters

The Packet Service Profile Parameters are as shown:

Packet Service Profile Parameters

Parameter

Length/Range

Description

packetServiceProfile

N/A

Specifies a unique identifier (name) for packet service profile. You can define any name or use Default as the parameter.

aal1PayloadSize

0-999

The ATM Adaption Layer Type 1 (AAL-1) payload size (default = 47).

audioTransparency N/A

Use this object to configure Audio Transparency settings.

  • unknownCodecBitRate – The bit rate, in Kilobytes/second, required for bandwidth computation of unknown audio codecs. (range: 1-1000 KB/sec / default = 124)
  • unknownCodecPacketSize – The packet size, in milliseconds, required for Bandwidth computation of unknown audio codecs. (range: 5-100 ms / default = 10)

If the bandwidth is not configured, the unknownCodecPacketSize and unknownCodecBitRate are used for the pass-through call.

codec

codecEntry1-codecEntry12

<codecEntry ID> <codec_name> – Defines the codec entry priorities and codec names. Up to 12 codec configurations are supported by SBC in PSX, ePSX and Advanced ERE deployment scenarios (see Routing and Policy Management for a description of the different routing configurations).

SBC-POL-RTU license is needed to enable more than four codecs.

 

The codecEntry IDs are listed below:

  • codecEntry1 – Codec entry with a priority of "1".
  • codecEntry2 – Codec entry with a priority of "2". 
  • codecEntry3 – Codec entry with a priority of "3". 
  • codecEntry4 – Codec entry with a priority of "4".
  • codecEntry5 – Codec entry with a priority of "5".
  • codecEntry6 – Codec entry with a priority of "6".
  • codecEntry7 – Codec entry with a priority of "7".
  • codecEntry8 – Codec entry with a priority of "8".
  • codecEntry9 – Codec entry with a priority of "9".
  • codecEntry10 – Codec entry with a priority of "10".
  • codecEntry11 – Codec entry with a ptriority of "11".
  • codecEntry12 – Codec entry with a priority of "12".

For each codecEntry ID, select a codec name. Example default codec names are:

  • G711-DEFAULT (default codec)
  • G711SS-DEFAULT
  • G711_NONE
  • G723-DEFAULT
  • G723A-DEFAULT
  • G726-DEFAULT
  • G729A-DEFAULT
  • G729AB-DEFAULT

dataCalls

N/A

Data calls pertaining to restricted or unrestricted digital data.

  • initialPlayoutBufferDelay Used for G.711 only. This is the initial playout delay for calls with a data bearer channel, for example, ISDN 64K data calls. This value is configured separately from the initial playout delay for voice channels (voiceInitialPlayoutBufferDelay) so providers can trade off delay on data calls versus the likelihood of jitter causing delay changes while the playout buffer adapts. Some data bearer calls are very sensitive to delay changes (such as H.320 video conferencing), so a higher initial delay should reduce the chance of jitter bursts causing problems. (range: 5-50 / default = 50).
  • packetSize <10 | 20 | 30 | 40> – The maximum data packet size (Kilobits). 
  • preferredRtpDataPayloadType – The RTP Payload Type included in the RTP header of the data packet.
    (range: 0-127 / default = 56)
dtlsN/A

Use this object to control DTLS-SRTP and DTLS fallback behavior in this Packet Service Profile.

  • dtlsCryptoSuiteProfile <profile name> – Name of DTLS Crypto Suite Profile.
  • dtlsFlags
    • allowDtlsFallback <disable | enable> – Enable flag to allow fallback to standard RTP when cryptographic attribute negotiation fails (default = disable).
    • enableDtlsSrtp <disable | enable> – Enable flag to allow Secure RTP.

See Configuring SBC for WRTC for configuration details.


flags

N/A

See Packet Service Profile Flags table below for flag descriptions

honorRemotePrecedence

N/A

Flag to set precedence of audio encoding priority order of the local packet service profile over the remote peers audio encoding priority order when creating the priority order of the audio encodings that are common to both. Options are:

  • disable (default) – Applies precedence to local audio encoding priority order, local Secure RTP/RTCP settings and crypto suite priority order.
  • enable – Applies precedence to the remote peer's audio encoding priority order. For ingress call legs, also applies precedence to remote peer's Secure RTP/RTCP settings and crypto suite priority order.

mediaPacketCos

0-7

Specifies Class of Service (COS) value to be set in the IEEE 802.1D User Priority field of media packets transmitted on a call leg that uses this Packet Service Profile. This parameter only has an effect if the network interface supports 802.1Q tagged Ethernet frames. (default = 0 which is interpreted as best effort).

packetToPacketControl

N/A

Use this object to define the packet-to-packet control parameters:

  • codecsAllowedForTranscoding – Use this parameter to specify codecs allowed for transcoding, and which leg to apply it to.
    • otherLeg <codec> (see codec list below)
    • thisLeg <codec> (see codec list below)
amrefrevrcg711a
g711ug722g726g729
g7221g7222g7231ilbc
opust38  
  • conditionsInAdditionToNoCommonCodec – The 
    Unable to show "metadata-from": No such page "_space_variables"
    performs transcoding when any of the specified conditions are met, including no common codec on ingress and egress legs.
    • applyFaxToneTreatment– Apply fax tone treatment.
      • disable (default)
      • enable
    •  different2833PayloadType– Enable this option to allow SBC to transcode media when RFC2833 payload type received from ingress is different from the preferred DTMF payload type configured in egress PSP.
      • disable (default)
      • enable
    • differentDtmfRelay – Enable this flag to perform transcoding when the ingress and egress call legs use different DTMF relay methods.
      • disable (default)
      • enable
    • differentPacketSize Enable this flag to perform transcoding when the ingress and egress call legs use different packet sizes.
      • disable (default)
      • enable
    • differentSilenceSuppression Enable this flag to perform transcoding when the ingress and egress call legs use different silence suppression methods.
      • disable (default)
      • enable
    • honorAnswerPreference– The SBC triggers a new offer towards the other side when an answer is received for a re-INVITE from this side. The re-INVITE generated on the other side carries all possible codecs in Route Packet Service Profile that causes the most preferred codec of the other side peer to be modified. Enable this Honor Answer Preference (HAP) flag to lock down the most preferred codec towards the peer irrespective of re-INVITE received for mid-call modification from this side. (See the table below describing SBC behavior when this flag is enabled/disabled).
      • disable (default)
      • enable
    • honorOfferPreference Enable this Honor Offer Preference (HOP) flag to honor the codec preference of the peer's offer when the 'Honor Remote Preference' flag on the PSX is enabled.  This option is available only when transcode = conditional. (See honorAnswerPreference vs. honorOfferPreference table below describing SBC behavior when this flag is enabled/disabled).
      • disable (default)
      • enable
  • transcode Transcode options:
    • conditional (default)
    • determinedByPspForOtherLeg
    • only
    • transcoderFreeTransparency (NOTE:  If using this option, you must also set lateMediaSupport to ‘passthru’ ( see sipTrunkGroup media - CLI))

The SBC, when configured with the appropriate codecs, transcodes for differences in the codecs. Use ‘transcode conditional’ option to allow the SBC to transcode for certain conditions in addition to differences in codecs. For example, if the codecs are the same on both legs and this option is selected, by applying additional settings for the particular call scenarios, the SBC will trigger transcoding for those scenarios, such as:

  1. Transcode for DTMF differences. For example, when both legs have same codec, but one uses inband for DTMF and the other RFC 2833.
  2. Transcode for Silence Suppression differences.
  3. Transcode for Packet Size differences.
  4. Transcode for RFC2833/4733 Payload differences. For example, when codecs are the same on both legs, but one side uses 101 as the Payload Type for DTMF and the other uses 102.
  5. Transcode always.

honorAnswerPreference vs. honorOfferPreference

HOP Flag StateHAP Flag StateSBC Behavior
enabledisableThe SBC selects a codec order of precedence in the offered SDP, irrespective of whether it is a pass-through or transcoded codec (if transcoding is defined for that codec). The SBC as part of media lock-down may send a re-INVITE to egress peer. Note that the preference on the answerer side is given to a pass-through codec.
enableenableThe SBC gives preference to HAP over HOP in case of conflict. The Honor Remote Preference (HRP) flag on the answerer leg decides the preference order. Based on that preference list, the SBC selects a codec with highest preference from answer SDP that can be used even if it requires transcoding. Note that this may cause the selection of a codec on the other side leg not to be honored. This happens in case of a pass-through call.
disableenableThe SBC gives preference to answerer codec order that is created based on HRP flag. The most preferred codec is chosen as received in the answer SDP, irrespective of whether it is a pass-through or a transcoded codec (if transcoding is defined for that codec).


peerAbsenceAction

N/A

  • none – (default) Inactivity detection is disabled.
  • peerAbsenceTrap – Choose this option to generate a trap if RTP inactivity is detected.
  • peerAbsenceTrapAndDisconnect – Choose this option to generate a trap and tear down the call if RTP inactivity is detected.
preferredRtpPayloadTypeForDtmfRelay

0-128

Specifies the preferred RTP payload type in the RTP header of audio packets for this encoding. (default = 128). This parameter is only used for 8 kHz clock rate. DTMF payload type of each subsequent clock rate (16 kHz, 24 kHz, etc.) is incremented by 1.

Using the default value of "128" for preferredRtpPayloadTypeForDtmfRelay implies that the preferred DTMF value (from the system configurable) is used for this profile.

If interworkDtmfWithoutTranscoding is enabled, ensure preferredRtpPayloadTypeForDtmfRelay is set to a valid value (96-127). If preferredRtpPayloadTypeForDtmfRelay value is invalid (set to "128"), the system may fail to pick up the value configured using "set system dspPad rtpDtmfRelay" command because DSPs are not used for the call.

qosValuesN/A

Use this object to configure the Quality of Service (QoS) DSCP value for this Packet Service Profile.

  • msrpDscp – The DSCP value to use for egressing MSRP packets (range: 0-255 / default = 0).

rtcpOptions

N/A

Use this object to specify Real Time Control Protocol (RTCP) options for the call. RTCP is used to report network traffic congestion data. Various actions (for example call disconnect) may be taken when congestion threshold settings are exceeded. The RTCP options are:

  • rtcp
    • disable (default)
    • enable – RTCP is used for the call.
  • packetLossAction – Packet loss action to take when packet threshold is exceeded:
    • none – Take no action.
    • packetLossTrap – Generate trap.
    • packetLossTrapAndDisconnect – Generate trap and disconnect.
  • packetLossThreshold – (default = 0) Enter a value between 0-32767 to specify the packet loss threshold (number of lost packets/100,000) which will trigger a packet loss action. This parameter is required if RTCP is enabled. When set to “0”, no packet loss inactivity detection is performed. See Command Example below for an example configuration.

    Configuring this parameter to a value less than 400 disables threshold detection, so be sure to use a value in the range of 400 to 32767 to enable threshold detection.

    This setting can be used in conjunction with  mediaPeerInactivity. To set media peer inactivity timeout value, see mediaPeerInactivity parameter in Media System - CLI page.

  • terminationForPassThrough – Specifies RTCP termination behavior for pass-through calls.
    • disable – (default) RTCP is relayed between the end points for pass-through calls. 
    • enable – Enable flag (as well as rtcp flag) on one leg to terminate RTCP sessions on each leg for pass-through calls. If RTCP and RTCP termination is enabled on one leg of a pass-through call, RTCP is terminated and originated for that leg. If RTCP is enabled on both legs on the pass-through call, irrespective of terminationForPassThrough settings, RTCP is always relayed.

secureRtpRtcp

N/A

Specifies whether secure RTP Real Time Control Protocol (SRTP) is enabled for the call:

  • cryptoSuiteProfile <profile name> – A unique identifier for the Cryptographic Suite Profile.
  • flags – Possible values are disable/enable. The default value of each flag below is "disable".
    • allowFallback – Enable flag to allow fallback to standard RTP/RTCP when crypto attribute negotiation fails.
    • allowPassthru – Enable flag to allow SBC to pass-through SRTP media without authenticating, decrypting, or encrypting it internally. SBC will prioritize SRTP pass-through media over terminated SRTP media. When this flag is disabled, SBC terminates all SRTP and SRTCP media for authentication, encryption, or decryption.

      To use this flag, enableSrtp flag must be enabled.

    • enableSrtp – Enable this flag to enable secure RTP/RTCP.
    • resetEncDecROCOnDecKeyChange – Enable flag to reset Roll Over Counter for both encryption and decryption when decryption key changes.
    • resetROCOnKeyChange – Enable flag to reset the SRTP Roll Over Counter when the session key changes.
    • updateCryptoKeysOnModify – For an SRTP call, if this flag is enabled in Packet Service Profile and call leg mode is changed from sendonly/inactive/recvonly to sendrecv, the SBC generates a new set of crypto attributes.

sendRoutePSPPrecedence

N/A

Use this flag to allow audio encoding order preference in outgoing messages only.

  • disable (default)
  • enable

silenceFactor

N/A

The percentage of call time that silence is expected. This parameter is used to reduce expected call bandwidth. (range: 0-50 / default = 40).

silenceInsertionDescriptor

N/A

Use this object to define the Silence Insertion Descriptor (SID) attributes.

  • g711SidRtpPayloadType – Specifies the G.711 Silence Insertion Descriptor (SID) RTP payloadType. (range: 0-127 / default = 19).
  • heartbeat – By default, this flag is enabled to allow SID packets to be sent within a minimal interval during a silence period (at least one SID packet must be sent within a SID maximum packet time frame).
    • disable
    • enable (default)

t38

N/A

Use this object to specify T.38 data rate attributes using following parameters:

  • dataRateManagementType:
    • type1LocalGenerationOfTcf – Type 1 data rate management requires that the Training Check Frame (TCF) training signal is generated locally by the receiving gateway. Data rate management is performed by the emitting gateway based on training results from both PSTN connections. Type 1 is used for TCP implementations and is optionally used with UDP implementations.
    • type2TransferOfTcf – (default) Type 2 data rate management requires that the TCF is transferred from the sending gateway to the receiving gateway rather than having the receiving gateway generate it locally. Speed selection is done by the gateways in the same way as they would on a regular PSTN connection. Data rate management type 2 requires the use of UDP and is not recommended for use with TCP.
  • ecm – Use this flag to allocate DSP resources, when available, for T.38 Error Correction Mode (ECM) calls.
    • disable – (default) use normal resource allocation.
    • enable
  • lowSpeedNumberOfRedundantPackets – This field specifies the number of redundant IFP messages sent in a UDP packet for T.38 low speed fax transmission, and applies only if the T.38 error correction type is redundancy. (range: 0-2 / default = 1).
  • maxBitRate – Use this object to select the T.38 Maximum Bit Rate which controls and manipulates bits 11, 12, 13, and 14 in the DIS command received by the SBC from either the TDM circuit interface or the T.38 packet interface:
    • 2.4Kbits_s – For modem type ITU-T V.27ter fall-back mode.
    • 4.8Kbits_s – For modem type ITU-T V.27ter.
    • 9.6Kbits_s – For modem types ITU-T V.27ter and V.29.
    • 14.4Kbits_s – (default) For modem types ITU-T V.27ter, V.29, and V.17. This setting is used to constrain the type of modem modulation schemes.
  • numberOfRedundantPackets – Use this parameter for high-speed fax relay to specify the number of redundant Internet Facsimile Protocol (IFP) messages sent in a User Datagram Packet (UDP) for fax transmission. (range: 0-2 / default = 1).
  • protocolVersion Use this parameter to specify the T.38 Fax protocol version to use.
    • 0 (default)
    • 3 

typeOfService

0-255

Use this object to Use this parameter to set six most significant bits of Type of Service byte in an IP header for DSCP marking of MSRP packets. Default value is 0.

videoCalls

N/A

Use this object to define video call parameters.

  • audioOnlyIfVideoIsPrevented– By default, this flag is enabled to allow call to continue with the audio only portion if the video cannot be established for any reason.
    • disable
    • enable (default)
  • codecListProfile – Name of the Codec List profile used to store precedence and purge lists of video codec MIME subtypes.
  • ieee8021QVLanCos – IEEE-802 1Q VLAN Class of Service. (range: 0-7 / default = 0)
  • ipv4Tos – IPv4 type of service. (range: 0-255 / default = 0)
  • ipv6TrafficClass – IPv6 traffic class. (range: 0-255 / default = 0)

ipv6TrafficClass is not supported with H.323 calls.

  • maxVideoBandwith – Maximum bandwidth in Kbps utilized by the video stream. (range: 0-50000 / default = 0).
  • videoBandwidthReductionFactor – The rate in which the maximum video bandwidth is reduced when IP resource allocation is performed. (range: 0-100 / default = 0).

voiceInitialPlayoutBufferDelay

1-50

The delay (in milliseconds) by the initial playout buffer required to absorb the maximum expected data packet delay across the network. Must be in increments of 1 ms. (default = 10).

Packet Service Profile Flags

ParameterDescription

HDCodecPreferred

This flag only applies when

Unable to show "metadata-from": No such page "_space_variables"
is configured with ePSX and/or external PSX.

Enable flag to set HD codecs as preferred codec over non-HD codecs even if transcoding is required. When flag is disabled, continue with existing PSP/IPSP behavior.

  • disabled (default)
  • enabled

When enabled,

If...Then...
the ingress Offer contains any valid HD codecsHD codecs are sorted to the top of the list while sending out the Offer.
all NB codecs are presentSBC reorders the codec entries with NB first, followed by HD codecs.
Codec selection priority from Answer message
  1. HD-HD pass-through
  2. HD-HD transcoding
  3. NB-NB pass-through
  4. NB-NB transcoding
  5. HD-NB transcoding

If forceRoutePSPOrder flag is enabled, this flag does not affect the ordering of outgoing offer.

The flag transcoderFreeTransparency overrides this flag. If  transcoderFreeTransparency is enabled, this flag is ignored.

MatchOfferedCodecGroupIfNbOnly

Enable this flag to allow the SBC to send only NB in outgoing offer if only NB is received in the ingress offer. Otherwise, do nothing. While sending the offer, this flag becomes is ignored if either HD-only or (HD+NB) is received in incoming offer.

If this flag is disabled, the SBC uses existing behavior.

  • disable (default)
  • enable

The flag transcoderFreeTransparency overrides this flag. If transcoderFreeTransparency is enabled, this flag is ignored.

digitDetectSendEnabled

Enable this flag to allow digit detection for pass-through calls on digits sent to the network.

  • disable (default)
  • enable

If interworking without DSP resources is desired for this Packet Service Profile, this flag must be enabled.


disallowDataCallsEnable flag to disallow data calls.
  • disable (default)
  • enable
dscpPassthrough

When enabled on both the Ingress and Egress call leg, the DSCP value in the IP header of the media packets is transparently passed through the system. Once media is received from the peer, any value set in the typeOfService field on the Packet Service Profile has no effect when dscpPassthrough is configured on both legs for the associated call.

  • disable (default)
  • enable

forceRoutePSPOrder

Enable this flag to send the outgoing offer in the same order as egress route Packet Service Profile irrespective of HD/NB priorities.

  • disable (default)
  • enable

If this flag is enabled, HDCodecPreferred flag does not affect the ordering of outgoing offer.

The flag transcoderFreeTransparency overrides this flag. If  transcoderFreeTransparency is enabled, this flag is ignored.

interworkDtmfWithoutTranscoding

Enable flag to interwork DTMF with out-of-band RFC2833 without the use of transcoding (DSP resources).

  • disable (default)
  • enable

If interworkDtmfWithoutTranscoding is enabled, ensure preferredRtpPayloadTypeForDtmfRelay is set to a valid value (96-127). If preferredRtpPayloadTypeForDtmfRelay value is invalid (set to "128"), the system may fail to pick up the value configured using "set system dspPad rtpDtmfRelay" command because DSPs are not used for the call.


preferNBPassthruOverHDTranscode

Enable this flag to allow the SBC to choose NB-NB pass-through over HD-HD transcoded call.

When disabled, the SBC prefers HD-HD transcoded call over NB-NB pass-through.

  • disable (default)
  • enable
This flag is valid only if HDCodecPreferred flag is enabled, and is applied when selecting a codec from answer.

The flag transcoderFreeTransparency overrides this flag. If  transcoderFreeTransparency is enabled, this flag is ignored.

reserveBwForPreferredAudioCommonCodec

By default, the SBC reserves the worst case common audio codec bandwidth for pass-through calls on trunk groups and IP interfaces, and polices the same bandwidth. Use this flag to reserve the bandwidth associated with the preferred common codec and police on the worst case codec. This flag applies to both known and unknown codecs, and can be used independently or in conjunction with Audio Transparency feature.

  • disable (default)
  • enable

This flag is active for a call when both the PSPs have this flag enabled. If this flag is disabled in any of the PSPs, the flag is not applied.


 ssrcRandomize

Enable flag to generate a new SSRC (using a random value) along with a new time stamp on a new RTP stream whenever a resource is reactivated (due to change in codec, etc.). SSRC randomization reduces the probability of collision in large groups and simplifies the process of group sampling that depends on uniform distribution of SSRCs.

  • disable (default)
  • enable 
useDirectMedia

Enable flag to use direct media as needed.

  • disable (default)
  • enable

validatePeerSupportForDtmfEvents

Flag to validate peer support for DTMF events. Enable this flag for all peer devices that support RFC 4733.

  • disable (default) – 
    Unable to show "metadata-from": No such page "_space_variables"
    does not validate the presence of DTMF events in the offer or answer from the peer. If DTMF relay is enabled, 
    Unable to show "metadata-from": No such page "_space_variables"
    transmits DTMF digits received from the other leg to this peer using the named event RTP payload.
  • enable – 
    Unable to show "metadata-from": No such page "_space_variables"
    validates the presence of DTMF events in the offer or answer from peers that support RFC 4733. If DTMF Relay is enabled and events 0-15 are received (with no other combination or subset of events), 
    Unable to show "metadata-from": No such page "_space_variables"
    forwards the events in the egress leg to this peer using the named event RTP payload. When 
    Unable to show "metadata-from": No such page "_space_variables"
    is configured for a pass-through call and it receives DTMF events other than 0-15 from the ingress peer, it does not offer any DTMF events to the egress endpoint.

 

Command Example

To configure RTCP options:

% set profiles media packetServiceProfile PSP-1 rtcpOptions rtcp enable
% set profiles media packetServiceProfile PSP-1 rtcpOptions packetLossAction packetLossTrap
% set profiles media packetServiceProfile PSP-1 rtcpOptions packetLossThreshold 10000
% commit

% show profiles media packetServiceProfile PSP-1
rtcpOptions {
rtcp enable;
packetLossThreshold 10000;
packetLossAction packetLossTrap;
}

To configure PSP to transcoderFreeTransparency on both legs:

% set profiles media packetServiceProfile PSP_INT packetToPacketControl transcode transcoderFreeTransparency 
% set profiles media packetServiceProfile PSP_EXT packetToPacketControl transcode transcoderFreeTransparency

To configure audioTransparecy feature on both legs:

% set profiles media packetServiceProfile PSP_INT audioTransparency unknownCodecBitRate 124
% set profiles media packetServiceProfile PSP_EXT audioTransparency unknownCodecBitRate 124

% set profiles media packetServiceProfile PSP_INT audioTransparency unknownCodecPacketSize 10
% set profiles media packetServiceProfile PSP_EXT audioTransparency unknownCodecPacketSize 10

% set profiles media packetServiceProfile PSP_INT flags reserveBwForPreferredAudioCommonCodec enable
% set profiles media packetServiceProfile PSP_EXT flags reserveBwForPreferredAudioCommonCodec enable

 

  • No labels