You are viewing an old version of this page. View the current version.
Compare with Current
View Page History
Version 1
Next »
This section provides information on the Sonus SBC 5400 hardware platform specifications.
Sonus SBC 5400 system is contained in a 2U rack-mounted chassis. The chassis can be front or center mounted in a standard 19-inch wide rack, with optional rack hardware to mount it in a 23-inch wide rack. At a high level, a fully populated SBC 5400 system is comprised of the following key components.
- Motherboard
- Four DSP2x modules
- Three Fan assemblies
- Solid state drive
- Two power supplies
SBC 5400 Chassis Front View
SBC 5400 Chassis Rear View
SBC 5400 Hardware Specifications
Front Panel | Rear Panel | Expansion (Modular) | Storage | Memory | Power Option |
---|
- Status Indicators Front Panel LEDs
- Single USB V2.0 interface
| - 4x100 Mb Management Ports
- Media Ports (1x10Gb or 4x1Gb)
- Two 1 Gb High Availability Ports
- 1x100 Mb Single Field Service port with RJ45 connector
- Locator LED
- Alarm port with HD15 connector
- Single serial craft DB9 port
| Up to four DSP2x cards | Minimum 480 GB Solid State Disk (SSD) | 32 GB RAM | AC or DC |
The chassis includes a front panel on which the various input/output ports and LEDs are located.
The Front Bezel and LEDs of SBC 5400 figure shows the front panel LEDs with and without Bezel mounted on the front panel of SBC 5400.
Front Bezel and LEDs of SBC 5400
The Front panel LEDs Description table lists the front panel LEDs on the SBC 5400. The default state of all LEDs are during a reset.
Front panel LEDs Description
Illustration | LED | Color | Description |
---|
1 | Front Power | Amber/Green | Power status indicator of all voltages generated on the module: - Green = All Power on
- Amber = BMC Power on
- Off = All Power is Off
|
2 | Front Status | Amber/Green | Module Status indicator |
3 | Front Active | Amber/Green | Module Redundancy State Indicator: |
4 | Front Alarm | Amber/Red | Module Critical/Major Failure Indicator: |
5 | Front Locator | White | Module identifier indicator. On or blinking, depending on the "ipmitool chassis identify" command. |
6 | FanCtl LED | Green | Fan module indicator: - Green = Fans are working
- Off = Module is not working
|
The following figures list the rear panel LEDs on the SBC 5400. The default state of all LEDs is during a reset. The rear panel layout and LEDs are as depicted in the Rear Panel LEDs for SBC 5400 figure:
Rear Panel LEDs for SBC 5400
The Rear Panel Description table lists the Ethernet port LEDs. Each of the Management ports, Media ports, HA ports, and FSP port support the following LEDs.
Component | Cable Requirement | Description |
---|
Alarm Port | Customer supplied cable | Alarm contact via a single shielded male HD15 connector. A single alarm port is present in SBC 5400 platform. This software release does not support the Alarm Port. |
Management Ports | CAT5e cable | Four Copper Ethernet Ports which process Management traffic and perform protocol termination. |
Locator | | Module identifier indicator |
Media Ports | Single mode or Multi mode fiber Copper CAT5e cable | Four copper SFP or fiber SFP ports for media and signaling traffic. |
High Availability Ports | Single mode or Multi mode fiberCopper CAT5e cable (NON-CROSSOVER TYPE ONLY) | Two copper SFP or fiber SFP ports for redundancy synchronization traffic. The platform supports box level redundancy via communication paths provided by the external HA Ethernet ports. |
Serial Port | Male DB9 connector | An RS-232 port used by BMC and control plane. The serial port uses a DB9 connector accessible from the rear panel. |
Field Service Port | Copper CAT5e cable | A single Field Service Port. |
Power Input | | Power Supply. The following are the descriptions of the power supply LED functions: - Off: No power input to the supply.
- Amber: Power supply fault.
- Blinking Amber: Main system power output fault.
- Blinking Green: Standby power to BMC is ON but main system power is not enabled.
- Solid Green: Both standby power to BMC and main system power are ON and OK.
|
Sonus-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.
CAT6 cabling may be required in environments where there is unusually high Electro-Magnetic interference (EMI) from power lines, manufacturing equipment, or certain types of lighting.
Ethernet Port LEDs Description
Port Type | Color | Description |
---|
Mgmt0/Mgmt1/Mgmt2/Mgmt3 | Green | Checks if the link and activity is present. - Green = Link
- Flashing = Activity
|
Media ports 0, 1, 2, and 3 | Green | Checks if the link and activity is present. - Green = Link
- Flashing = Activity
|
HA ports 0 and 1 | Green | Checks if the link and activity is present. - Green = Link
- Flashing = Activity
|
Field Service Port | Green | Checks if the link and activity is present. - Green = Link
- Flashing = Activity
|
The SBC 5400 chassis comprises the following external input and output ports:
- Alarm contacts are provided on the outside of the chassis through a single shielded male HD15 connector.
- A standard USB connector on the front of the chassis.
- Front and rear jacks for standard ESD straps.
- Cable management.