Signaling - Global - CLI

In this section:

These sections describe the configuration objects used for signaling. The following diagram depicts a basic signaling configuration.

Call Signaling Configuration Objects

Diameter Signaling Controls

Use this object to configure global Diameter signaling controls.

Command Syntax

% set global signaling diamSigControls
	addSonusSpecificAVP <disabled | enabled>
	defaultCCF <ipAddress>
	enableRfApp <disabled | enabled>
	generateFailedEventAcr <disabled | enabled>
	maxACRretransmission <0-3>
	rfInterimAccInrvl <0-180>

Command Parameters

Diameter Signaling Control Parameters

Parameter	Length/Range	Description
`addSonusSpecificAVP`	N/A	Enable this flag to send additional CDR information within Ribbon vendor-specific Attribute Value Pairs (AVPs) in Accounting-Request (ACR) messages over the existing Rf Interface. `disabled` (default) `enabled` NOTE: Refer to Rf Interface Support for AVP details.
`defaultCCF`	Up to 32 characters	`<ip address>` – Specify the IP address to use as the default CCF realm configuration if CCF is not received in the PCFA. (default = 0.0.0.0)
`enableRfApp`	N/A	Use this flag to enable the Rf Accounting application at the system level to send accounting information over Rf Interface. Refer to Rf Interface Support for feature details. `disabled` (default) `enabled`
`generateFailedEventAcr`	N/A	Enable flag to prevent failed call ACR event from being sent. `disabled` (default) `enabled`
`maxACRretransmission`	0-3	<#> – Set the maximum number of ACR retransmissions to use if the Unable to show "metadata-from": No such page "_space_variables" does not receive ACA (default = 3).
`rfInterimAccInrvl`	0-180	`<#>` – Use this parameter to specify the interim account interval value to send when no interval is received in ACA. Set value to “0” to not send interim record (default = 30). NOTE: If ACA has a different value than `rfInterimAccInrvl`, this parameter is overwritten.
`sigOnlyModeValue`	N/A	This global option controls whether the SBC is in signaling-only mode. `global` – Places the Unable to show "metadata-from": No such page "_space_variables" in signaling only mode and automatically enables direct media on all trunk groups and all IPSPs. `off` (default) NOTE: You can only switch the Unable to show "metadata-from": No such page "_space_variables" into or out of signaling-only mode when no active calls are present in the system.

Gateway Signaling Timers

This object allows you to configure the signaling timers for the gateway.

Command Syntax

% set global signaling gwSigTimers
   congRelDelay <delay in seconds>
   establish <timer value, in seconds>
   idle <idle time, in hours>
   keepalive <keepalive time, in seconds>
   retry <number of minutes to attempt to recover GW signaling link>
 
% show global signaling gwSigTimers
 
% delete global signaling gwSigTimers

Command Parameters

Global Gateway Signaling Timers Parameters

Parameter	Description
`congRelDelay`	Amount of time (in seconds) that a call which is rejected due to congestion will be delayed before the release is issued. (default = 0).
`establish`	The Gateway Signal Channel Establishment Timer (in seconds.) This value applies to all signal channels. (default = 10).
`idle`	Amount of time (in hours) a GW Signaling Link May be idle before it is taken down. (default = 0).
`keepalive`	The Gateway Signal Channel Keep-alive Timer (in seconds.) This value applies to all signal channels. (default = 3).
`retry`	Amount of time (in minutes) the SBC will continue to attempt to recover a GW Signaling Link as long as there are stable calls up. (default = 60).

H.323 Signaling Timers

This object allows you to configure signaling timers for the node.

Command Syntax

% set global signaling h323SigTimers 
   establish <timer value, in seconds>
   t301 <timer value, in seconds> 
   t302 <timer value, in seconds> 
   t303 <timer value, in seconds> 
   t304 <timer value, in seconds> 
   t310 <T3timer value, in seconds10> 
   tcpConnect <tcpConnect> 

% show global signaling h323SigTimers
 
% delete global signaling h323SigTimers

Command Parameters

Global H.323 Signaling Timers Parameters

Parameter	Length/Range	Description
`establish`	0-127	The H225 signal channel establishment timer (in seconds). Default value is 4.
`t301`	0-65535	The T301 call timer (in seconds). Default value is 180 seconds.
`t302`	0-127	The T302 call timer (in seconds). Default value is 15 seconds.
`t303`	0-127	The T303 call timer (in seconds). Default value is 4 seconds.
`t304`	0-127	The T304 call timer (in seconds). Default value is 20 seconds.
`t310`	0-127	The T310 call timer (in seconds). Default value is 10 seconds.
`tcpConnect`	0-127	The TCP connect timer (in seconds). Default value is 3 seconds.

Command Example

To display the global configuration of all h323SigTimers:

% show global signaling h323SigTimers  
   establish 33;  
   tcpConnect 77;  
   t301 444;  
   t302 33;  
   t303 22;  
   t304 33;  
   t310 33;

Signaling Only Mode

The SBC can be configured in a signaling-only mode so that the SBC participates in the exchange of signaling messages that set up a call but does not reserve or allocate any media resources for the session. The media component of the session is handled as direct media between the call participants.

Command Syntax

% set global signaling sigOnlyMode sigOnlyModeValue <global | off>

Command Parameters

Signaling Only Mode Examples

Parameter Description

sigOnlyModeValue

This global option controls whether the SBC is in signaling-only mode. The options are:

global - places the SBC in signaling only mode and automatically enables direct media on all trunk groups and all IPSPs.
off (default)

Command Example

% set global signaling sigOnlyMode sigOnlyModeValue global
commit

SIP Peer Overload Control

This object allows you to configure SIP Peer Overload parameters.

Command Syntax

% set global signaling sipPeerOverloadControl 
   discardPeriod <1-10 seconds> 
   rejectThreshold <0-50> 
   samplingPeriod <1-10> 
   stepDownGain <1-200>
% show global signaling sipPeerOverloadControl
  
% delete global signaling sipPeerOverloadControl

Command Parameters

Global SIP Peer Overload Control Parameters

Parameter	Length/Range	Description
`discardPeriod`	1-10	Discard period (in seconds) for the Peer Overload back-off algorithm. (default = 2).
`rejectThreshold`	0-50	Specifies the reject threshold (in rejects/sec) for the Peer Overload backoff algorithm. (default = 1).
`samplingPeriod`	1-10	Specifies the sampling period (in seconds) for the Peer Overload back-off algorithm. (default = 2).
`stepDownGain`	1-200	Specifies the step down gain for the Peer Overload back-off algorithm. (default = 100).
`displaylevel`	1-64	To display different levels of output information in show commands.

Command Example

To display the global configuration of all SIP overload control:

% show global signaling sipPeerOverloadControl  
   samplingPeriod 2;  
   discardPeriod 1;  
   stepDownGain 44;  
   rejectThreshold 33;

SIP Signaling Controls

Use this object to configure SIP signaling control parameters.

Command Syntax

% set global signaling sipSigControls 
	egressRemoveEnudmi <disabled | enabled>
    egressRNParam <disabled | enabled> 
	loopDetectionFeature <disabled | enabled> 
	maxPduSizeValue <pdusize2kb | pdusize3kb | pdusize6kb | pdusize15kb | pdusize32kb | pdusize60kb> 
	multipleContactsPerAor <disabled | enabled>
	registrarSupportContactParam <disabled | enabled>
    send503DuringSwitchover <disabled | enabled>
	sendDeRegisterContactAsStar <disabled | enabled>
	sendSurrogateUnRegAfterReboot <disabled | enabled>
	suppressErrorInfoHdr <disabled | enabled>
	surrogateRegisterPacingTime <0-10000>
	ucidNodeId <node_id>
 
% show global signaling sipSigControls
 
% delete global signaling sipSigControls

Command Parameters

Global SIP Signaling Control Parameters

Parameter	Length/Range	Description
`egressRemoveEnudmi`	NA	Controls whether the SBC removes the `enumdi` (ENUM dip indicator) parameter from the egress Request-URI that the SBC inserts when the PSX does an ENUM query. The options are: `disabled` (default) - The SBC includes the `enumdi` parameter in the egress Request-URI when the PSX does an ENUM query. `enabled` - The SBC does not include the `enumdi` parameter in the egress Request-URI even if the PSX does an ENUM query.
`egressRNParam`	N/A	Enable this flag to send a Redirecting Number Information Element (RNIE) in the egress leg of the call per RFC3398 when the R-URI and the To header differ. `disabled` `enabled` (default)
`loopDetectionFeature`	N/A	When enabled, the SIP Stack performs loop detection on incoming INVITE messages. `disabled` – The SIP signaling group processes the INVITE message. `enabled` (default)
`maxPduSizeValue`	N/A	The maximum PDU size recognized by the Unable to show "metadata-from": No such page "_space_variables" : `pdusize2kb` – 2,048 bytes `pdusize3kb` – 3,072 bytes `pdusize6kb` – 6,000 bytes `pdusize15kb` (default) – 15,000 bytes `pdusize32kb` – 32,000 bytes `pdusize60kb` – 60,000 bytes
`multipleContactsPerAor`	N/A	Use this flag to support multiple contacts per Address Of Record (AoR). `disabled` – Only a single contact per Address of Record is supported. `enabled` (default) – The SBC maintains different RCBs for each new registration and verifies the source IP address and port during Registration Control Block (RCB) lookup. The SBC supports validating the source IP address and the port even if `multipleContactsPerAor` flag is disabled. The SBC also supports locating the RCB using the AoR to perform additional validation on the source IP address and port if the parameter `requireRegistration` is set to "required" or "required-non-priority". This is applicable for both calls and OOD requests that are originated from the IAD. In case of refresh registration that is originated from a different IP/port, the SBC forwards the request to the registrar and move the sate to "UPDATING". Any calls or OOD requests that are originated from the IAD while the RCB is in updating state must be validated using the previously authenticated IP/port. When the flag `multipleContactsPerAor` is enabled, the SBC maintains different RCBs for each new registration. A registration is considered new when the source IP/port of the REGISTER request is different from earlier registration for the same AoR. Any of the registered UEs may initiate a communication on behalf of the AoR, and the SBC fetches the corresponding RCB based on source IP port of the UE. NOTE: Refer to Multiple Contacts per AoR feature page for additional details. NOTE: Even though the default value of `multipleContactsPerAor` is "enabled", during an upgrade the value can be either "enabled" or "disabled".
`registrarSupportContactParam`	N/A	Enable flag to support parameters in the Contact header: `disabled` – Parameters in the Contact header are not supported. This value is provided only for backwards compatibility. `enabled` (default) – Parameters in the Contact header are supported.
`send503DuringSwitchover`	N/A	Use this flag to control the sending of 503 message during a switchover. `disabled` – The request is dropped with no 503 messages sent for Invites. `enabled` (default) – Send 503 message during a switchover. NOTE: The Retry-after tag is set to 60 seconds once the 503 message is sent.
`sendDeRegisterContactAsStar`	N/A	Enable this flag to allow the Unable to show "metadata-from": No such page "_space_variables" to send the Contact header as a star (*) in DEREGISTER messages if `multipleContactsPerAor` is disabled. `disabled` `enabled` (default)
`sendSurrogateUnRegAfterReboot`	N/A	Enable flag to trigger de-register messages to all AORs configured to use the Surrogate Registration feature after a reboot. `disabled` (default) `enabled`
`suppressErrorInfoHdr`	N/A	Enable flag to suppress Error-Info header in a response to a request message with syntax error. `disabled` (default) – The SBC includes Error-info header in the response. `enabled` – The SBC does not include Error-Info header in an error status.
`surrogateRegisterPacingTime`	0-10000	Use this parameter to specify the time gap, in milliseconds, between a final response of surrogate register and the next surrogate register message sent across all peers. (default = 0, disabled) If surrogate registration is active and you wish to disable pacing, first disable surrogate registration for each peer using following command syntax: % set addressContext <AC name> zone <zone name> ipPeer <peer name> surrogateRegistration state disabled NOTE: Please research the feature to fully understand pacing semantics before using it. This setting is not required in generic deployments. Pacing is applied to all surrogate REGISTER requests generated for all surrogate AoRs.
`ucidNodeId`	1-32767	UCID Node Id used to generate the UCID in the User-to-User Header. (default = 0)

Command Example

To display the global configuration of all SIP signaling control parameters:

% show global signaling sipSigControls
loopDetectionFeature         enabled;
registrarSupportContactParam enabled;
suppressErrorInfoHdr         enabled;
maxPduSizeValue              pdusize3kb;
egressRNParam                enabled;
multipleContactsPerAor       enabled;
surrogateRegisterPacingTime  enabled;
ucidNodeId                   13;
}

Single Radio Voice Call Continuity (SRVCC)

SRVCC provides the ability to transition a voice call from the VoIP/IMS packet domain (LTE) to the legacy circuit domain. Variations of SRVCC are being standardized to support both GSM/UMTS and CDMA 1x circuit domains. For an operator with a legacy cellular network who wishes to deploy IMS/VoIP-based voice services in conjunction with the rollout of an LTE network, SRVCC offers VoIP subscribers with coverage over a much larger area than would typically be available during the roll-out of a new network.

Command Syntax

% set global signaling srvcc
    atcfUri (1-63 chars)
    callLingerTimer (1-32 seconds)
    eStnSr (1-32 chars)
	pstopsSti (0-32 chars)
    stnSr (1-32 chars)

Command Parameters

Global SRVCC Parameters

Parameter	Length/Range	Description
`atcfUri`	1-63 characters	The SIP URI to be used as the ATCF Path and Management URI.
`callLingerTimer`	1-32 seconds	Number of seconds to wait for INVITE due to STN_SR before clearing the call (default=32).
`eStnSr`	0-32 characters	The Request URI for a emergency transfer call sent by MSC on PS to CS call hand-off. Acceptable characters: alphabetical (upper- and lower-case), numerical (0-9) and any of the following special characters: +,-,.,(,)
`pstopsSti`	0-32 characters	The Request URI for a Packet-Switched-to-Packet-Switched (PS-to-PS) optimized hand-over call. Acceptable characters: alphabetical (upper- and lower-case), numerical (0-9) and any of the following special characters: +,-,.,(,)
`stnSr`	0-32 characters	The Request URI for a transfer call sent by MSC on PS to CS call hand-off. Acceptable characters: alphabetical (upper- and lower-case), numerical (0-9) and any of the following special characters: +,-,.,(,)

Command Example

set global signaling srvcc pstopsSti +1-pstopsSti-222
commit

show global signaling srvcc pstopsSti
pstopsSti +1-pstopsSti-222;

Space shortcuts

Page tree

Diameter Signaling Controls

Command Syntax

Command Parameters

Gateway Signaling Timers

Command Syntax

Command Parameters

H.323 Signaling Timers

Command Syntax

Command Parameters

Command Example

Signaling Only Mode

Command Syntax

Command Parameters

Command Example

SIP Peer Overload Control

Command Syntax

Command Parameters

Command Example

SIP Signaling Controls

Command Syntax

Command Parameters

Command Example

Single Radio Voice Call Continuity (SRVCC)

Command Syntax

Command Parameters

Command Example