Logging Into EMA

HTTPS Support

The EMA GUI is available via TLS-secured (https) access either directly through port 443 or indirectly through port 80 to 443. ACL rules are not applicable to prevent unsecured (http) access.

A sample X.509 certificate, which is a copy of the BMC and the EMA Platform Mode certificate, is shipped along with the 

The EMA uses the common Local Cert store of the 

Certificates with RSA keys up to 4,096 bits are supported.

Enter the following URL in the browser to access the

https://<hostname>

where, the <host name> is one of the management IP addresses of the

The EMA uses a self-signed certificate which may produce a warning message by Internet Explorer and Firefox. These messages may be ignored.

Logging In

Supported Browsers and Client Computers

Refer to 

Procedure

Following are the steps to log into the Embedded Management Application (EMA):

1. Launch your web browser.

2. Enter the

   Unable to show "metadata-from": No such page "_space_variables"
   EMA URL <ip address/device name>
   Note

   Sometimes, when using Internet Explorer/Mozilla Firefox browser, website security issue may prevent you from going directly to the  SBC application login screen as shown in example below.

   Click Advanced.

   Certificate Security Error

   

   Click Add Exception.

   Firefox Message - Self-Certified Website

   
   Uncheck the Permanently store this exception check-box and click Confirm Security Exception.

   Firefox Message - Add Security Exception

   
    

   The Login window appears as shown below:

   Login

   

3. Enter Username and Password. Your Username and the Password will be supplied along with the

   Unable to show "metadata-from": No such page "_space_variables"
   installation package. Once you have successfully logged in to SBC, you temporary password expires and you are prompted to change your password.
   Note

   This change password screen appears only for the first log on of the new user.

   Change Password

   

   
   Ensure the following criteria are met to successfully change the password:

• Minimum length of characters is 8.
• Minimum number of upper case characters is 1.
• Minimum number of lower case characters is 1.
• Minimum number of numeric digits is 1.
• Minimum number of special characters is 1.
• Maximum number of consecutive repeating characters is 3.
• Minimum number of differences compared to the old password is 4.
• Do not repeat any of the last 4 passwords.
4. Once the password is successfully changed, enter the Username and the new Password and click Log In.

Incorrect Username-Password Combination

If you enter incorrect Username-Password combination, the following error message is displayed:

EMA Incorrect Login Credentials

Information in the Login Window

The Login window displays the following:

• Username
• Password

The following table describes the login window components.

Messages After Successful Login

After you log on to the EMA, you may get one of the following messages:

• If you enter the correct login credentials:

  Successful EMA Login

  

• If you make mistake, or someone had tried to unsuccessfully log on using your username but gave the wrong password:

  EMA Login Message - Previous Unsuccessful Message

  

Last Login Display Date

The last login date of the user is displayed during the login time. When a user logs into the CLI/EMA, his/her last successful and failed login date and the IP address is displayed. The user evaluates this information to check illegal activities in the account.The information which are displayed at login:

1. Last successful login date and time.
2. Last successful login IP address.
3. Last unsuccessful login date and time.
4. Last unsuccessful login IP address.

5. Number of failed attempts after successful login.

    

Configuring Banner in Login Screen

1. On the main screen, navigate to Admin > Application Management. Click Banner chiclet on the left hand side of the page to display the Configure Login Banner window.
   
   
2. Enable Show Login Banner option. You can request the user to acknowledge the Banner by enabling the Require User to Acknowledge Banner before Logging in option and also, you can request the user to acknowledge every time they login or only during the first login.
   
   
3. Add your banner text in the text box next to Banner Text option to display your Banner content.
   
   
4. Click Save to save your edits.

Logging Out of EMA

To log out of the EMA:

1. Hover the mouse pointer over <your_username> on the menu bar. and click Log Out.

   Log Out

   

2. Confirm logging out by clicking Yes on the dialog-box.

   Log Out Confirmation

   

Security Enhancement to Allow Only One Concurrent EMA Session

This enhancement enables the EMA application (including EMA in platform mode) to disable concurrent user login sessions. Once a new session is established, any existing session is terminated immediately. When an EMA user attempts to log on, the system validates for any open sessions with the same username. If any existing user session is identified, the user is immediately logged out from the application and allows the new user to log on to the system.

EMA User Logged Out Automatically