Updating the ASM Recovery Partition

This operation allows you to load new software into the Recovery partition of the ASM. There are a number of reasons why you would want to do this:

• To update the recovery partition with newer software, allowing one to be better prepared should they need to Re-initialize the ASM at a later date.
• To put a completely different software load onto the ASM. For example, convert a Windows only ASM to an SBA ASM or vise versa. To do so, follow this procedure then perform the procedure described in the Re-initializing the ASM section.

Before You Begin

In addition, you will need to obtain:

• An empty USB flash drive, 8GB or larger.
• The software image you would like to load. These can be obtained from the Ribbon SBC Edge Download Center.

Preparing the USB Flash Drive

1. Insert the flash drive into your PC.
2. Format the flash drive for the NTFS file system (if you have not done so already). This is necessary due to the large size of the image files.
   To perform this in Windows, do the following:
   1. Browse to Computer and find the flash drive.
   2. Right-click it, and select Format....

   3. Select NTFS from the File system dropdown, and click Start.

      Format PNY

      

       

       

3. Locate the image file mentioned above - we require a file called ASMimage.tar.
4. Copy ASMimage.tar to the root directory of the USB drive.

Load a New ASM Image from USB

1. Insert the prepared flash drive into one of the ASM USB ports of the
   Unable to show "metadata-from": No such page "_space_variables"
   SBC 1000/2000 system.

   • Updating the ASM Recovery Partition on the SBC 2000- directly plug it into the USB Port for the ASM.

     Click to read more...

     Front Panel

     

     #	Name	Description
     1	Reset	System reset button. For more information, see Resetting the Ribbon SBC 1000-2000 to Factory Defaults.
     2	USB Ports	USB ports for SBC 1000/2000 main board.
     3	Power	Power Status LED
     4	Alarm	Alarm Status LED
     5	Peer Node	Peer Node Status LED (also recognized as the Locator LED)
     6	Ready	Ready Status LED
     7	Admin Port	System Administration Ethernet Port – do not connect to your live network - see warning below.
     8	Ports 1 - 4	Ethernet Ports 1 - 4
     9	USB Ports	USB ports for the Application Service Module (ASM) (when installed)
     10	Ethernet Port Status	Ethernet Status LED

      Admin Port

     The Administrative IP port should be used for Running Initial Setup, as well as all management related functionality from the web browser.

     Application Ethernet Ports

     When two or more LAN Ethernet ports are on the same Bridge (as in the factory-default Ribbon SBC 1000/2000 configuration), they must not be connected to the same Ethernet switch or Ethernet network. Doing so creates a broadcast loop in the Ethernet network, rendering the network unusable. You may work around this issue by connecting the Ethernet ports directly to an intelligent switch or router running a spanning tree protocol.

   • Updating the ASM Recovery Partition on the SBC 1000- directly plug it into the USB Port for the ASM.

     Click to read more...

     SBC 1000 Front Panel with USB and Ethernet Ports

     

      

     1	Reset	System reset button. For more information, see Resetting SBC Edge to Factory Defaults.
     2	USB Ports	USB ports for SBC Edge 1000/2000 main board – see USB ports below.
     3	Status LEDs	Click here for details.
     4	Ethernet Port 1 - 3	Ethernet Ports 1-3 with Ethernet Status LEDs

      

     ---

      

     SBC Edge 1000 Front Panel with USB, Ethernet, and T1/E1 Ports

     

     1	Reset	System reset button. For more information, see Resetting SBC Edge to Factory Defaults
     2	USB Ports	USB ports for SBC Edge 1000/2000 main board – see USB ports below.
     3	Status LEDs	Click here for details.
     4	Ethernet Ports 1-3	Ethernet Ports 1-3 with Ethernet Status LEDs.
     5	T1/E1 Ports	Available when licensed. See Managing Telephony Ports for details.

      

     ---

     SBC Edge 1000 Front Panel with USB, Ethernet, SBA, and ASM Ports

     

     1	Reset	System reset button. For more information, see Resetting SBC Edge to Factory Defaults
     2	USB Ports	USB ports for SBC Edge 1000/2000 main board – see USB ports below.
     3	Status LEDs	Click here for details.
     4	Ethernet Ports 1-3	Ethernet Ports 1-3 with Ethernet Status LEDs.
     5	Ethernet Port 4	For CCE connection to Office 365 To connect the ASM to a second network To connect a VM to a different network than the ASM
     6	USB Ports	USB ports for the Application Service Module (ASM).

      

     ---

      

     SBC Edge 1000 Front Panel with USB, Ethernet, T1/E1, and SBA Ports

     

      

     1	Reset	System reset button. For more information, see Resetting SBC Edge to Factory Defaults
     2	USB Ports	USB ports for SBC Edge 1000/2000 main board – see USB ports below.
     3	Status LEDs	Click here for details.
     4	Ethernet Ports 1-3	Ethernet Ports 1-3 with Ethernet Status LEDs.
     5	T1/E1 Ports	Available when licensed. See Managing Telephony Ports for details.
     6	Ethernet Port 4	For CCE connection to Office 365 To connect the ASM to a second network To connect a VM to a different network than the ASM
     7	USB Ports	USB ports for the Application Service Module (ASM)

      

     ---

     USB Ports

     Usage

     The SBC Edge 1000 front panel includes two pairs of USB ports.

     Callout Number	Purpose
     2	These ports are used to attach an external USB drive to store core dumps for troubleshooting and as a survivability mechanism for Active Directory Caching (when configured). See Support section below for proper usage.
     6 (in Fig. 3) 7 (in Fig. 4)	If your SBC Edge 1000 has a built-in Application Service Module (ASM), this USB port is primarily used for Updating the ASM Recovery Partition, and to (optionally) transfer files between a USB drive and the ASM.

     Support

     The following section is applicable only to the USB ports on location 2 on the SBC Edge 1000 front panel.

     For the SBC Edge to properly recognize the USB thumb drive, you must ensure the following prerequisites are satisfied:

     • The USB storage must be of FAT32 file format.
     • The storage must be at least 1GB (or more) in size.
     • The SBC does not require a reboot after the USB drive is installed.

2. In the WebUI, click the Tasks tab.
3. In the left navigation pane, under Application Solution Module, click Update ASM Recovery Partition.

4. Click the Apply button to begin the installation of the new image.

   Loading and installing the new image can take up to 10 minutes.

5. Wait for the following message to be displayed:

   Image Installation Complete

   

    

    

6. Remove the USB flash drive from the system.

The Recovery partition has now been updated.