SBC SIP Transparency Implementation Guide

1. Introduction

This document provides configuration and provisioning guidance to enable SIP transparency on

1.1 Audience

This document is intended for design engineers, system engineers and operations staff for the purpose of deploying SIP on a 

1.2 Support

• Phone: +1 888-391-3434 (Toll-free) or +1 978-614-8589 (Direct)
• Web: https://doc.rbbn.com/display/PORTAL/Salesforce+Login

2. SIP Transparency

For some SIP elements, transparency is a frequently-debated topic. When transparency for a SIP header or body is desired, the user may often compare the element against a SIP Proxy which is a typical benchmark for significant transparency. Considered a popular comparison, this topic needs to addressed up front when discussing SIP transparency.

2.1 SIP Proxy vs. SIP B2BUA

The SIP devices that connect most peers and endpoints are typically a SIP Proxy or Back-to-Back User Agent (B2BUA). The most transparent device is the SIP Proxy; its behaviors are primarily specified in RFC 3261 and are very basic in its message processing capabilities. The required transparency of a Proxy is one of its few strengths when compared to a B2BUA.

SIP Transparency Spectrum

Although an

While RFC 3261 goes into detail describing the required behavior of a SIP Proxy, its description for a B2BUA could be considered somewhat terse: "Since it is a concatenation of a UAC [User Agent Client] and UAS [User Agent Server], no explicit definitions are needed for its behavior." This statement notwithstanding, debate and research into the transparency behavior of a B2BUA continued, but seemingly without consensus. An often referenced IETF draft (draft-marjou-sipping-01) submitted to the SIPPING WG was not accepted as a working group document.

Admittedly, complete SIP transparency is not achievable due to the needs and requirements of changing some headers. Even a SIP Proxy is not completely transparent. In many scenarios the ability to control and even minimize transparency is a strength of a B2BUA/

• SIP Normalization (including arbitrary SIP Message Manipulation)
• Topology Hiding
• Protocol Translation
• Codec Transcoding (allowing a non-transparent SDP)

Fundamentally, the 

This document describes the

3. 

Unable to show "metadata-from": No such page "_space_variables"

SIP Transparency and Control Mechanisms

Since its inception, the 

3.1 Existing 

Unable to show "metadata-from": No such page "_space_variables"

Transparency Mechanisms

Prior to release 4.0, SIP header and body transparency was controlled primarily by the use of individual Transparency Flags, mostly within the IP Signaling Profile (IPSP; ipSignalingProfile > commonIpAttributes > transparencyFlags) and apply on the egress leg of a session (egress relative to the SIP message).

If a header or body did not have a specific flag on the

When a transparency flag was added for a header, it meant that the header was now known and that the unknownHeader flag no longer controlled it.

This methodology was problematic as headers transitioned from unknown to known on the

The 

3.2 SIP Transparency Profile

A Transparency Profile is a user-configurable profile allowing the user to transparently pass almost any SIP header/body through the

Both already-known and previously-unknown SIP headers and bodies can be configured in a Transparency Profile. By default, no headers or message bodies are present in a Transparency Profile. If a received Content-Type header value matches any “Message Body” entry configured in the Transparency Profile, the

The following functionality is included:

• Ability to transparently pass "all" SIP headers and message body types.
• Selectively ignore transparency of select headers and message body types (useful when transparency is enabled for all headers and/or message body types).
• Exclude one or more methods for which transparency of headers or message body types is not needed.

When configuring a Transparency Profile for specific SIP headers,

The following transparency is not supported by the

• PRACK messages and responses to PRACK messages are not sent end-to-end through the
  Unable to show "metadata-from": No such page "_space_variables"
  . Therefore, the
  Unable to show "metadata-from": No such page "_space_variables"
  does not support transparency of message-bodies or headers in these messages.
• ACK messages are not normally sent end-to-end through the
  Unable to show "metadata-from": No such page "_space_variables"
  . Transparency of ACK messages is not supported even if the endToEndAck flag is enabled in the "IP Signaling Profile".
• In late media scenarios, the
  Unable to show "metadata-from": No such page "_space_variables"
  does not support transparency of headers and bodies.
• Transparency for headers and bodies is not supported for methods such as CANCEL and methods that are "hop-by-hop".

For configuration details, see Service Profiles - Transparency Profile (EMA) or Transparency Profile - CLI.

3.2.1 SIP Message Header

The 

set profiles services transparencyProfile <profile> sipHeader <SIP Header>

where <SIP Header> is case insensitive, supports up to 31 characters, and supports an "all" entry to match all headers (see section 3.3 for exceptions).

The ability to exclude specific headers from transparency is primarily intended for use in conjunction with the "all" header option.

SIP headers are also configurable using compact form. When configuring specific headers in a Transparency Profile,

Compact form can be received by the

The 

The following SIP headers are not controlled by the Transparency Profile (or any Transparency Flags), and are ignored if configured in a Transparency Profile:

• Allow
• Call-ID
• CSeq
• Max-Forwards
• Require
• RSeq
• Supported

If Contact Header is specified in a Transparency Profile, then it is treated as full Contact transparency and it will take precedence over other Contact related flags (such as useZoneLevelDomainNameInContact).

3.2.2 SIP Message Body

set profiles services transparencyProfile <profile> sipMessageBody <Content-Type> 

where <Content-Type> is case insensitive, supports up to 127 characters, and supports an "all" entry to match all message bodies except those described in the below list.

The following Content-Types are not controlled by the Transparency Profile and are ignored if configured in a profile:

• application/sdp
• application/dtmf
• application/dtmf-relay
• application/sonus-media
• application/broadsoft
• application/isup
• multipart/mixed
• multipart/alternative

Multipart/mixed and multipart/alternative are ignored because the 

A Transparency Profile cannot control the SDP (application/sdp). The SDP and its controls will be discussed later in this document.

The other exceptions are due to existing Relay Flags (see table below) elsewhere within the 

See Relay Flags below for details.

3.2.3 Inter-working with IP Signaling Profile

SIP Transparency Profile provides advanced control of the transparency of headers and message bodies. However, customers may continue with the existing (albeit simple) IPSP transparency controls in PSX/e-PSX/ERE.

Using message body transparency as an example:

• If a message body is allowed by the IPSP but configured to be ignored by the Transparency Profile, it is not transparently passed through.
• If a message body is allowed by the IPSP but configured to be excluded by the Transparency Profile for a particular SIP method, it is not transparently passed through for that specific SIP method.
• If specific message bodies are allowed by the IPSP, but transparency of 'all' message bodies is configured in the Transparency Profile, all types of message bodies are transparently passed through.
• If 'Unknown Body' transparency is enabled in the IPSP, but an unknown message body is configured to be ignored (or excluded for a specific SIP method) by the Transparency Profile, it is not transparently passed through.

3.3 SIP Header Transparency

Header transparency is based on the headers that are present in the Transparency Profile of the egress trunk group for requests and headers that are present in the ingress trunk group for responses. By default, no headers are present in the Transparency Profile.

3.3.1 Allowed Values for a SIP Header in the Transparency Profile

A 'sipHeader' in the Transparency Profile can be composed of:

• Any string with a maximum length of 31 characters
• Any case, lower/upper/mixed
• Special characters are allowed

3.3.2 SIP Headers not Under Transparency Control in Relay Scenarios

Some headers are not under the control of transparency flags in relay scenarios. These headers can be classified into three categories as shown in the below table:

3.3.3 SIP Headers Not Transparently Passed in Calls

The following SIP headers are not supported by a Transparency Profile (or any Transparency flags):

• Call-ID
• RSeq
• Allow
• CSeq
• Max-Forwards
• Require
• Supported

These SIP headers are entirely added and/or modified by the 

3.3.4 SIP Headers Brought Under Transparency Control in Relay Scenarios

Previously, the following headers were transparently passed by the

• Accept
• SIP-ETag
• SIP-If-Match
• Suppress-If-Match

3.3.5 SIP Header Transparency Behaviors

There are some exceptions to the transparency mechanisms. Some SIP Methods and some SIP headers are not affected by any configurable transparency mechanism, while other headers may not be affected by transparency controls in some scenarios (in-dialog vs. out-of-dialog).

3.3.6 Non-Transparent Methods and Scenarios

The following SIP methods are not supported by a Transparency Profile (or any Transparency flags):

• ACK (even if the endToEndAck flag is enabled)
• CANCEL
• PRACK

3.3.7 Transparently Pass or Block Option Tags/Methods of Allow/Require/Supported Headers

Option tags/methods of the following SIP headers can be transparently passed or blocked by configuring the SIP Param Filter Profile.

• Allow
• Require
• Supported

3.3.8 In-Dialog vs. Out-of-Dialog

Some header behaviors vary depending on whether they are received in or out of an existing dialog. While the Transparency Profile has been extended in 4.2 to apply to out-of-dialog messages, there are some specific headers whose behavior is not under the control of a Transparency Profile (or Transparency Flags) when received in out-of-dialog messages.

A Dialog "represents a peer-to-peer SIP relationship between two user agents that persists for some time. The dialog facilitates sequencing of messages between the user agents and proper routing of requests between both of them. The dialog represents a context in which to interpret SIP messages." (reference: RFC 3261)

The 

Out-of-Dialog header behavior irrespective of the Transparency Profile or Flags:

3.4 SIP Message Body Transparency

Message body transparency is based on message bodies that are present in the Transparency Profile of the egress trunk group for requests and content-types/bodies that are present in the ingress trunk group for responses. By default, no message bodies are present in the Transparency Profile.

SIP Message Flow

3.4.1 Allowed Values for a Content Type in the Transparency Profile

The allowed range for a "contentType" in the Transparency Profile includes:

• Any string with a maximum length of 127 characters
• Any case, lower/upper/mixed
• Special characters are allowed
• An existing transparency flag for that Content-Type in IP Signaling Profile (IPSP) is not required

3.4.2 Transparency of Multi-part Message Bodies

The

For example, consider a SIP message with content-type 'multipart/mixed' with two parts in its body: the first part is type 'application/foo' and the other type 'application/bar'. If the Transparency Profile is configured to transparently pass 'application/foo', then the first part of the message body is passed transparently in the egress SIP message.

3.4.3 Support for Message Body Transparency Across Sonus Gateways

This feature will be supported across Sonus Gateways (using Sonus Proprietary GW to GW Signalling) only for SIP INVITE messages.

3.4.4 SDP

he

1. Audio
2. Video Main
3. Video Extended (for Content Share)
4. Binary Floor Control Protocol (UDP and TCP)
5. Far End Camera Control (FECC)
6. Message Session Relay Protocol ( MSRP)

For all the above mentioned media types (with the exception of Audio), the 

• C line
• RTCP attributes
• Media direction (a= sendrecv/sendonly/inactive/recvonly)

• Unable to show "metadata-from": No such page "_space_variables"
  supports Secure Real-Time Transport Protocol (SRTP) media pass-through for SRTP and Secure Real-Time Transport Control Protocol (SRTCP) media streams.

For Audio, the 

You must enable Video (assign a valid video bandwidth) and Audio transparency to achieve the above described behavior using the below CLI syntax.

% set profiles media packetServiceProfile <packetServiceProfileName> packetToPacketControl transcode transcoderFreeTransparency
% set addressContext <addressContextName> zone <zoneName> sipTrunkGroup <trunkGroupName> media sdpAttributesSelectiveRelay enabled
% set addressContext <addressContextName> zone <zoneName> sipTrunkGroup <trunkGroupName> media lateMediaSupport passthru 

3.4.4.1 SDP Transparency Flag

Make note that the sdpTransparencyState signaling object within the SIP Trunk Group must not be considered a general use parameter. It is specific to some functionality (mainly ICE) and environments; however, this flag does not apply to all types of call flows.

3.4.5 Audio Transparency

The

• recvonly/sendonly/sendrecv/inactive
• crypto
• X-dmi
• rtcp
• fingerprint
• OMR

Audio Transparency Feature is controlled by two flags:

• Enable Transcoder-Free-Transparency for the session (enable on either of the PSPs).
• Enable Selective-SDP-Transparency on both ingress and egress Trunk Groups that receive the relayed SDP.

Bandwidth (b) lines are transparently relayed and do not play any role in calculating the unknown audio codec bandwidth. The following PSP configuration bits for Audio Transparency feature are included for Unknown audio bandwidth reservation to calculate the Unknown audio bandwidth:

• unknownCodecBitRate

• unknownCodecPacketSize

3.4.5.1 Audio Transparency and Reserve Bandwidth for Preferred Common Codec

By default for pass-through calls, 

3.4.5.2 Media Policer Reservation For Worst Case Codec

By default for pass-through calls, the

3.4.5.3 Configuring Audio Transparency

Configuring the basic audio transparency feature contains:

• Enabling the sdpAttributesSelectiveRelay Parameter on Both Ingress and Egress Trunk Groups
• Configuring the transcoderFreeTransparency Parameter on Packet Service Profile
• Configuring audioTransparecy Parameter on Packet Service Profile

Enabling the sdpAttributesSelectiveRelay Parameter on Both Ingress and Egress Trunk Groups

% set addressContext default zone ZONE1 sipTrunkGroup TG_SBX_INT media sdpAttributesSelectiveRelay enabled
% set addressContext default zone ZONE2 sipTrunkGroup TG_SBX_EXT media sdpAttributesSelectiveRelay enabled

Configuring the transcoderFreeTransparency Parameter on Packet Service Profile

% set profiles media packetServiceProfile PSP_INT packetToPacketControl transcode transcoderFreeTransparency 
% set profiles media packetServiceProfile PSP_EXT packetToPacketControl transcode transcoderFreeTransparency

Configuring AudioTransparecy Parameter on Packet Service Profile

% set profiles media packetServiceProfile PSP_INT audioTransparency unknownCodecBitRate 124
% set profiles media packetServiceProfile PSP_EXT audioTransparency unknownCodecBitRate 124

% set profiles media packetServiceProfile PSP_INT audioTransparency unknownCodecPacketSize 10
% set profiles media packetServiceProfile PSP_EXT audioTransparency unknownCodecPacketSize 10

% set profiles media packetServiceProfile PSP_INT flags reserveBwForPreferredAudioCommonCodec enable
% set profiles media packetServiceProfile PSP_EXT flags reserveBwForPreferredAudioCommonCodec enable

3.5 Transparency Profile Usage

As discussed previously, the Transparency Profile does not deprecate any existing Transparency Flag. Those flags continue to function as designed. When a header/body is specified in a Transparency Profile, then the profile takes precedence over any applicable Transparency Flag. For headers/bodies not specified in a transparency profile, the setting of existing Transparency Flags continues to determine the transparency of that header.

When configuring a Transparency Profile for specific SIP headers,

There are three modes of using Transparency Profile:

• Transparency Profile with Specific Headers (Positive Enumeration)

• Maximum Transparency Using the Transparency Profile

• Transparency Profile, All Headers with Exceptions (Negative Enumeration)

3.5.1 Transparency Profile with Specific Headers (Positive Enumeration)

In this mode, only headers/bodies explicitly configured in the Transparency Profile are allowed to pass-through.

For example, the following scenario allows only the headers "p-asserted-identity" and "xyzHdr" and message bodies of type "application/simple-message-summary" and "xyzContentType" to pass transparently.

set profiles services transparencyProfile ALLOW_SPECIFIC_HDRS_BODIES sipHeader p-asserted-identity
set profiles services transparencyProfile ALLOW_SPECIFIC_HDRS_BODIES sipHeader xyzHdr
set profiles services transparencyProfile ALLOW_SPECIFIC_HDRS_BODIES sipMessageBody application/simple-message-summary
set profiles services transparencyProfile ALLOW_SPECIFIC_HDRS_BODIES sipMessageBody xyzContentType
set profiles services transparencyProfile ALLOW_SPECIFIC_HDRS_BODIES state enabled
commit

3.5.2 Maximum Transparency using the Transparency Profile

Complete or maximum transparency is occasionally desired, especially during initial integration testing to determine if specific headers are required for the success of certain call flows.

set profiles services transparencyProfile MAX_TRANSPARENCY sipHeader all
set profiles services transparencyProfile MAX_TRANSPARENCY sipMessageBody all
set profiles services transparencyProfile MAX_TRANSPARENCY state enabled
commit
set addressContext <AC> zone <ZONE> sipTrunkGroup <TG> services transparencyProfile MAX_TRANSPARENCY
commit 

Additional Relay Flags also need to be enabled to maximize the transparency of the Trunk Group for testing. See Relay Flags above.

3.5.3 Transparency Profile, All Headers with Exceptions (Negative Enumeration)

All headers/bodies are allowed to pass-through unless they are explicitly disallowed by Transparency Profile configuration. The ignoreTransparency header option within the Transparency Profile is primarily used for excluding one or more specific headers when paired with the "all" header option. In the example below, the user wishes to pass all SIP headers except for the History-Info header.

For example, in the following scenario, the rules are configured and all the headers and message bodies except "history-info" and "application/resource-lists+xml" are passed transparently. The "xyzHeader" is passed transparently in all methods except INFO and REGISTER. The "xyzContentType" is passed transparently in all methods except INVITE.

set profiles services transparencyProfile ALMOST_ALL_TRANSPARENCY sipHeader all
set profiles services transparencyProfile ALMOST_ALL_TRANSPARENCY sipMessageBody all
set profiles services transparencyProfile ALMOST_ALL_HDRS sipHeader history-info ignoreTransparency yes
set profiles services transparencyProfile ALMOST_ALL_HDRS sipMessageBody application/resource-lists+xml ignoreTransparency yes
set profiles services transparencyProfile ALMOST_ALL_HDRS sipHeader xyzHeader excludedMethods info,register
set profiles services transparencyProfile ALMOST_ALL_HDRS sipMessageBody xyzContentType excludedMethods invite
set profiles services transparencyProfile ALMOST_ALL_HDRS state enabled
commit

The excludedMethods parameter indicates the list of methods for which the transparency is not allowed and is common to both header and body entries.

set profiles services transparencyProfile TP1 sipHeader all
set profiles services transparencyProfile TP1 sipHeader all excludedMethods bye,info,notify
commit

3.5.4 Existing Deployment Augmented with a Transparency Profile

Existing deployments will likely utilize Transparency Flags, and those that must pass proprietary or otherwise 

While a Transparency Profile can be configured to completely overlap with any existing Transparency Flags settings, it is not required. A Transparency Profile can be configured to simply augment existing Transparency Flags settings with a more surgical configuration and allowing unknownHeader to be disabled.

For example, a user may wish to have the 

Rather than continue to allow all unknown headers through the

set profiles services transparencyProfile IDENTITY_HDRS sipHeader Identity
set profiles services transparencyProfile IDENTITY_HDRS sipHeader y
set profiles services transparencyProfile IDENTITY_HDRS sipHeader Identity-Info
set profiles services transparencyProfile IDENTITY_HDRS sipHeader n
set profiles services transparencyProfile IDENTITY_HDRS state enabled
commit
set addressContext <AC> zone <ZONE> sipTrunkGroup <TG> services transparencyProfile IDENTITY_HDRS
commit
set profiles signaling ipSignalingProfile <IPSP> commonIpAttributes transparencyFlags unknownHeader disable
commit

3.6 SRTP Pass-through

The following diagram illustrates the media flow for an SRTP pass-through call.

SRTP Packet to Packet Media Call Flow

To control this SRTP media pass-through, the allowPassthru flag is available from the secureRtpRtcp parameter of the PSP. When allowPassthru flag is enabled along with the security enableSrtp flag, it allows SBC to pass-through SRTP media without authenticating, decrypting, and encrypting it internally. When selected, this flag prioritizes SRTP pass-through media over terminated SRTP media. When disabled, this flag terminates all SRTP and SRTCP media for authentication, encryption, or decryption. This flag is disabled by default.

3.7 Relay Flags

Relay Flags exist mostly within the IP Signaling Profile (IPSP; ipSignalingProfile > commonIpAttributes > relayFlags) and apply on the ingress leg of a session (ingress relative to the SIP message).
Relay Flags are intended mainly for SIP Methods (Requests) and Responses (and some SIP message bodies) that normally get consumed or modified by the 

Albeit imprecise, a good method to contrast Relay Flags and Transparency Flags/Profiles is to consider that Relay controls whether a SIP request/response is sent through the

3.8 Relaying REFER Request

The 

If the refer relay flag is disabled, the Call Control (CC) mechanism forwards the REFER request to Digital Signaling (DS). DS exchanges information with the PSX to check the match criteria set in Conditional Relay Matching. 

The matched criteria includes call parameters such as Username, Directory Number (DN), or Fully Qualified Domain Name (FQDN).

• If the call parameters received with the REFER request match the call routing criteria, 
  Unable to show "metadata-from": No such page "_space_variables"
  relays the REFER request to Egress SIPSG.
• If the call parameters received with the REFER request do not match the call routing criteria, the REFER request is processed locally by
  Unable to show "metadata-from": No such page "_space_variables"
  . The REFER request acts as the transferor and the call is forwarded to the Egress SIPSG, resulting in call bridging. In this scenario, 
  Unable to show "metadata-from": No such page "_space_variables"
  sends back a 202 response and proceeds for local processing.

The following figure shows the enhanced REFER request processing call flow:

3.8.1 Configuring 

Unable to show "metadata-from": No such page "_space_variables"

For Enhanced Refer Processing

To configure this feature, perform the following steps:

1. Configure 
   Unable to show "metadata-from": No such page "_space_variables"
   for regular REFER call Blind Transfer.
   
   

2. Create SIP_MSG_TYPE_REFER call parameter filter profile (CPFP) in the PSX. Execute the following command to view the CPFP SIP_MSG_TYPE_REFER. This profile is already present in ERE.

   Info

   For more information on creating CPFP, refer to PSX Documentation.

   > show table profiles callParameterFilterProfile
   Description:
   Profile used for routing based on SIP message type.
   
   Possible completions:
     SIP_MSG_TYPE_INFO      - SIP Message Type is Info
     SIP_MSG_TYPE_MESSAGE   - SIP Message Type is Message
     SIP_MSG_TYPE_NOTIFY    - SIP Message Type is Notify
     SIP_MSG_TYPE_REFER     - SIP Message Type is Refer
     SIP_MSG_TYPE_REGISTER  - SIP Message Type is Register
     SIP_MSG_TYPE_SUBSCRIBE - SIP Message Type is Subscribe
     none                   - seed data for provisioning support
   
   

   All > Profiles > Call Parameter Filter Profile

   Call Parameter Filter Profile List showing SIP_MSG_TYPE_REFER profile

   
   Note

   A new script SONS_SIP_REFER_RELAY is seeded in both ERE and PSX.

3. Disable the Refer relay flag in IPSP.

   % set profiles signaling ipSignalingProfile DEFAULT_SIP commonIpAttributes relayFlags refer disable

4. Enable the Notify relay in Egress side on IPSP to relay REFER for DN/Username/FQDN match.

   % set profiles signaling ipSignalingProfile DEFAULT_SIP commonIpAttributes relayFlags notify enable

   All > Profiles > Signaling > Ip Signaling Profile > Common Ip Attributes > Relay Flags

   Notify and Refer relay flags

   

5. Create a new routing label with the script SONS_SIP_REFER_RELAY to trigger process refer request feature.

   Note

   The routing label action must be set as script.

   % set global callRouting routingLabel <routing_label> script SONS_SIP_REFER_RELAY action script

   All > Global > Call Routing > Routing Label

   Creating a Routing Label

   

   Routing Label screen

   

6. Configure a DN criteria in the standard route and attach the SIP_MSG_TYPE_REFER profile to the standard route by executing the following command:

   % set global callRouting route none Sonus_NULL Sonus_NULL standard  <Matched_DN or FQDN> 1 all ALL SIP_MSG_TYPE_REFER Sonus_NULL routingLabel <routing_label>

   For DN (Directory Number) or username

   % set global callRouting route none Sonus_NULL Sonus_NULL standard <Matched_DN or Username> 1 all ALL SIP_MSG_TYPE_REFER Sonus_NULL  routingLabel <routing_label>

   For FQDN with DN or username

   Note

   The corresponding Sip domain group must be configured in

   Unable to show "metadata-from": No such page "_space_variables"

   .

   % set global sipDomain <Matched_domain_name >
    
   % set global callRouting route none Sonus_NULL Sonus_NULL standard <Matched_DN or Username> 1 all ALL SIP_MSG_TYPE_REFER  <Matched_domain_name> routingLabel <routing_label>
   
   

   All > Global > Call Routing > Route

   Creating a Route

   

   Route screen

   

7. Execute the following commands to view the call detail status and call media status.

   > show status global callDetailStatus 
   or
   > show status global callMediaStatus 
   
   

3.9 SIP Param Filter Profile

The 

The SIP Param Filter Profile includes the following characteristics:

• This profile takes precedence over existing mechanism/flags when transparently passing Allow/Supported/Require headers, but does not impact corresponding configurations established by the operator. It is operators responsibility to ensure the system is configured properly so that transparently-passed values do not conflict with existing configurations. For example, do not configure 100rel as pass-through if 100rel support fro SIP Trunk Group Signaling is disabled.
• The settings of SIP Param Filter Profiles for both ingress and egress legs dictate the actual pass-through results (see SIP Param Filter Profile Behavior table below for details.)
• Pass-through of individual header values is configurable.
• SIP tags are provided for unknown SIP parameter transparency only. Known SIP parameter transparency is still determined using existing SBC application logic (from Ingress leg to Egress leg) and configurations.

The following table explains the SIP Param Filter Profile behavior when using the Allow, Supported and Require headers.

3.10 SIP Filter Profile

The SIP Filter Profile is a collection of the configurable filter settings of individual SIP headers. Depending on the filter settings of each of the SIP headers in the SIP Filter Profile, the SBC either relays the SIP messages without parsing the header, or parses the headers of the messages.

For every SIP message associated with the ingress leg of the call, the SBC first checks the SIP Filter Profile for the filter setting of the SIP header. If the SIP Filter Profile indicates that a particular SIP header needs filtering, the SBC stores it without parsing.  

The SIP header of the egress leg is populated on the basis of the configuration in the IP Signaling Profile and the Transparency Profile. In the egress leg of a call, the transparency bit mask is set to identify the headers that are transparently passed. If the transparency settings of all unknown headers in the IP Signaling Profile is enabled, all the stored headers (including the ones filtered in the ingress leg), is copied to the SIP header of the egress leg.

If the Transparency Profile attached with the Egress Trunk Group indicates that specific headers are allowed to pass transparently, and those headers are present as filtered headers, they are individually copied to the SIP header of the egress leg. In this case, the transparency bits are enabled, either by the IP Signaling Profile or through the flexible header transparency.

Configuring a SIP Filter Profile

Perform the following:

• Creating a new SIP Filter Profile
• Changing the Transparency Setting of a Header Under a SIP Filter Profile
• Configuring the Zone ID for the Selected Zone
• Configuring the Media IP Interface Group Name for a SIP Trunk Group
• Attaching the SIP Filter Profile to the SIP Trunk Group

Creating a new SIP Filter Profile

% set profiles signaling sipFilterProfile doc_FILTER2

Changing the Transparency Setting of a Header Under a SIP Filter Profile

% set profiles signaling sipFilterProfile doc_FILTER2 header Also enabled

Configuring the Zone ID for the Selected Zone

% set addressContext default zone doc_ZONE_IAD id 10

Configuring the Media IP Interface Group Name for the SIP Trunk Group

% set addressContext default zone doc_ZONE_IAD sipTrunkGroup doc_SBX10_IAD media mediaIpInterfaceGroupName LIF1

Attaching the SIP Filter Profile to the SIP Trunk Group

% set addressContext default zone doc_ZONE_IAD sipTrunkGroup doc_SBX10_IAD signaling sipFilterProfile doc_FILTER2     

3.11 Privacy Transparency

A new flag anonymizeHostIpAddress is introduced for the privacy parameter of the IP Signaling Profile to enable or disable this feature. When this flag is activated, the SBC anonymizes the incoming host IP portion of the private headers (P-AID, P-PID, RPID) by replacing it with the IP address of the SBC, before sending it to the egress leg of a call.

Enabling the transparency Flag

To enable the transparency flag for an ipSignalingProfile, enter the following command:

% set profiles signaling ipSignalingProfile DEFAULT_SIP egressIpAttributes privacy transparency enable

Enabling the anonymizeHostIpAddress Flag

To enable the anonymizeHostIpAddress flag to activate this feature, enter the following command:

% set profiles signaling ipSignalingProfile DEFAULT_SIP egressIpAttributes privacy anonymizeHostIpPortion enable