You are viewing an old version of this page. View the current version.

Compare with Current View Page History

Version 1 Next »

Back to Table of Content

Back to Configuring SBC Objects

In this section:

This section provides an example for configuring DNS Groups and explains how to configure DNS A/SRV and NAPTR queries.

Configure DNS Groups

The

Unable to show "metadata-from": No such page "_space_variables"
 supports domain-name resolution via external DNS servers. Each IP address context defines one or more DNS server groups, each containing up to eight DNS servers. The zone and/or SIP Trunk Group then indicates which DNS Server Group to use for requests requiring DNS resolution.

When a DNS group is configured at the Address Context level for an interface, it must also be configured at the Zone level in that Address Context. For example, the CLI command examples listed below accomplish the following:

  1. Configure DNS group "DNG-1" for Address Context "default" to include IP interface type, local resource record and DNS server settings.

  2. Set DNS group to zone within Address Context.

    % set addressContext default dnsGroup DNG-1 type ip interface IPIG-1  
% set addressContext default dnsGroup DNG-1 localRecord RECORD1 data 1 hostName HOST-1 order roundrobin state enabled  
% set addressContext default dnsGroup DNG-1 server SERVER1 ipAddress 1.1.1.1 priority 1 recursionDesired true weight 10  
% set addressContext default zone ZONE_AS dnsGroup DNG-1

     

Note

The SBC Core supports up to eight DNS servers per DNS group. The SBC 5000/7000 series platforms support up to 2,048 DNS Groups system-wide. SBC SWe supports up to 128 DNS Groups. See SBC Provisioning Limits for additional provisioning limitations. 


Configure DNS A/SRV and NAPTR Queries

The 

Unable to show "metadata-from": No such page "_space_variables"
supports DNS A/SRV and NAPTR Queries. The DNS Group and DNS support type configuration is required in the 
Unable to show "metadata-from": No such page "_space_variables"
to trigger the DNS Queries to the DNS Server.

Perform the following steps to configure the DNS server for DNS A/SRV and NAPTR queries:

  1. Create a DNS group and add a DNS server in the group.

    More than one DNS server can be added. Each is selected based on its weight and the priority.

    % set addressContext a1 dnsGroup <dnsgroupname> server <servername> ipAddress <DNS ipaddress> state enabled

     
     

  2. In the SIP Trunk Group services, create a Static route for the DNS Server.

    % set addressContext a1 zone <zone_name> sipTrunkGroup <trunkgrp name> services dnsSupportType a-srv-naptr 
% set addressContext a1 staticRoute <dns ip address> <prefix> <gateway ip> <Intfce> <if_ethx> preference 10

     
     

  3. In the IP Signaling Profile, enable the "noPortNumber5060" flag. 

    % set profiles signaling ipSignalingProfile <SIP IP signaling profile name> commonIpAttributes flags noPortNumber5060 enable

     

  4. Ensure that IP Peer returns the domain name so the SBC can send the query to the DNS Server. 

    % set addressContext a1 zone <dnsgroupname> ipPeer <peer name> policy sip fqdn <Domain name> fqdnPort <port>

     

    For NAPTR/SRV lookups, ensure the port number is not configured under IP Peer on the SBC, or IP Signaling Peer Group in the PSX, if external PSX is used. If only A-record lookups are required, the port must be configured.



  5. Check the DNS server status and statistics:

    % show table/status addressContext a1 dnsGroup DNSGroup1 dnsServerStatistics
% show table/status addressContext a1 dnsGroup DNSGroup1 dnsEntryStatus
% show table/status addressContext a1 dnsGroup DNSGroup1 dnsEntryDataStatus

 

Refer to the following pages for  command syntax details:


  • No labels