On this page:
Configure FXS Ports
To configure FXS ports:
- In the WebUI, click the Settings tab.
In the left navigation pane, go to Node Interfaces > Ports.
Port Table View
FXS Long Loop
By using the FXS long loop feature, the maximum length of the local loop supported by SBC1K/2K FXS line cards can be extended to 3000 meter. To accomplish this, you must configure the Long Loop on per FXS line card. The FXS port on this line card supports devices connected using up to 3000 meters long cables.
Configuring FXS Long Loop on SBC 1000
In case of SBC1000, enabling the long loop on an FXS line card can reduce the number of available ports by disabling the upper FXS cards in the system.
Enabling FXS long loop on a line card disables the FXS line card in the corresponding upper slot. For example, enabling long loop on FXS line card in slot 1 of the SBC1000 disables the FXS line card in slot 2 of the SBC. FXS long loop does not affect FXO line cards in the upper slots.
Following is the procedure to configure long loop.
In the WebUI, go to Settings > Node Interfaces > Ports.
The Port Table View window appears.Port Table View
Select SET FXS Local Loop Type option on the top of the window. The following window appears.
Local Loop Type window
Select the FXS long loop for FXS line card in Slot 1 and Slot 3.
You can select FXS long loop for FXS line card in Slot 1, Slot 3, and Slot 5, based on your requirement. There are two available options: Long Loop and Standard.
Click OK.
A confirmation window appears. You are prompted to confirm the changes.
Confirmation Window
Click OK.
If you want to discard the changes, click Cancel.
Once this selection is submitted, all the changes are applied to the FXS Line card in each slot. The The following Port Table View window shows port type for each slot. The Port Type is changed form FXS to FXS Long Loop in slot 1 and slot 3.
Also, the FXS line card in slot 2 and slot 4 are disabled and are unavailable to handle calls. This infers that the upper FXS cards in the system are disabled if long loop is applied.Port Table View After Applying FXS Long Loop
Viewing Monitor Tab
To view real-time status, click the Monitor tab in the WebUI.
The following image shows that the FXS Module 2 and FXS Module 4 are not displayed under Sonus SBC 1000 Main Board.
Monitor View
Viewing Overview Tab
To view the system overview, in the WebUI, go to System > Overview.
The following image shows that Telco Module 2 and Telco Module 4 are disabled.
Overview Tab
Viewing Ports Inventory
To view your Sonus SBC 1000/2000 System's assets, go to System > Inventory Report tab.
The following image shows that Telco Module 2 and Telco Module 4 are disabled.
Inventory Report
Configuring FXS Long Loop on SBC 2000
In the WebUI, go to Settings > Node Interfaces > Ports.
The Port Table View window appears.Port Table View
Select SET FXS Local Loop Type option on the top of the window. The following window appears.
FXS Long Loop Type
Select the FXS long loop for FXS line card in Slot1 and Slot 2.
Click OK.
A confirmation window appears. You are prompted to confirm the changes
Confirmation Window
Once this selection is submitted, all the changes are applied to the FXS Line card in each slot. The following Port Table View window shows port type for each slot. You can see that the Port Type is changed to FXS Long Loop.
Port Table View after applying FXS Long Loop
Viewing Monitor Tab
To view real-time status, Click the Monitor tab in the WebUI.
Monitor Tab
Viewing Overview Tab
To view the system overview, go to System > Overview.
The Port Status panel shows that the Port Type is changed to FXS Long Loop.
Overview Tab
Viewing Ports Inventory
To view your Sonus SBC 1000/2000 System's assets, in the WebUI, go to System > Inventory Report tab.
The Ports panel shows that the Port Type is changed to FXS Long Loop.
Inventory Report
Modifying a Port
To modify a Port:
Click the expand (
) Icon next to the entry you wish to modify.
) Icon next to the entry you wish to modify.
Modifying a Port
Identification/Status - Field Definitions
The Identification/Status Panel controls the network identity of the port and its administrative state (Up or Down). It also provides the port's current service status and when that status last changed.
Port Alias
Specifies an alias for the port. This text is configured by the operator for exclusive use by SNMP-based element and network management systems to assign a key to the port or interface, that is unique across the managed network. Examples would be "Node10Port5" and "VerizonPort5"
Admin State
Specifies the administrative state of the port.
Physical Layer - Field Definitions
Analog Line Profile
Analog line profiles allow users to change the impedance presented by the Sonus SBC 1000/2000 FXS ports. It should match the impedance of the specified country's Telco. Some countries use resistive impedance and some use complex impedance. For example, telephone companies in the United States use 600 ohm resistive impedance where as Australia uses 220 ohms in series with the parallel combination of 820 ohms and 120 nF.
Relative Profile Adjustments
- Negative values represent signal attenuation (lower volume).
- Positive values represent signal amplification (higher volume).
Receive Gain
Allows you to control the gain or loss (in decibels) to the received voice levels.
Transmit Gain
Specifies the gain or loss in decibels to apply to the transmitted voice levels.
Receive and Transmit Gain affect FAX functionality. Use/Modify with care.
Overview
Content Tools