Configuring HPC/GETS Feature

Overview

To configure the HPC/GETS feature, perform the following configuration steps:

SBC Configuration

This section describes the minimal configuration of the SBC for the HPC/GETS features.

Configure hpcCallLimits and policer rate in sipCacProfile

Command Syntax

% set profiles sipCacProfile <profile_name>
	hpcCallLimits
		maxCalls <unlimited | blockAll | 1-1000> 
		maxIngressRate <unlimited | 1-2000> 
		ingressRateInterval <1-30> 
		bucketSize <1-4000> 

Relevant GETS Parameters

Table 1: hpcCallLimits Parameters

Command Example

% set profiles sipCacProfile testSipCacProfile hpcCallLimits maxCalls 500 maxIngressRate 50 ingressRateInterval 10 bucketSize 32
% commit

Configure DSCP marking for DIAMETER+ packets

Command Syntax

• Configure the dscpProfile.

  % set profiles services dscpProfile <dscp_profile_name>
  	hpcDscpValue <0-63>
  	dscpValue <0-63>
  	state <disabled | enabled>

• Attach the configured dscpProfile with policyServer globalConfig.

  % set system policyServer globalConfig dscpProfile <dscp_profile_name>

• Configure mediaPortRange.

  % set system media mediaPortRange
  	highPriorityPortRangeLocation <bottom | top>
  	highPriorityPortRangeSize <0-25>

Relevant GETS parameters

Table 2: hpcCallLimits Parameters

Command Example

% set profiles services dscpProfile HPC hpcDscpValue 32 dscpValue 22 state enabled
% commit

% set system policyServer globalConfig dscpProfile HPC
% commit

% set system media mediaPortRange highPriorityPortRangeLocation bottom highPriorityPortRangeSize 10
% commit

Configure DSCP for useRecvdValue

Command Syntax

% set profiles services hpcCallProfile <profile_name> 
	dscp <egress | ingress> 
	useRecvdValue <disabled | enabled>

Relevant GETS parameters

Table 3: dscp Parameters

Command Example

The following examples are applicable for egress and ingress call legs:

% set profiles services hpcCallProfile testHpcCallProfile dscp egress useRecvdValue disabled
% commit

% set profiles services hpcCallProfile testHpcCallProfile dscp ingress useRecvdValue disabled
% commit

% set profiles services hpcCallProfile testHpcCallProfile dscp egress useRecvdValue enabled
% commit

% set profiles services hpcCallProfile testHpcCallProfile dscp ingress useRecvdValue enabled
% commit

Configure HPC Call Queuing

Prerequisite

By default, the SBC sends a response code 600 when the call queue is full. If the configuration requirement is to send the response code 503 when the call queue is full, execute the following commands:

• Configure causeMap 161 to correspnd with sipCause 503.
  Command Syntax:

  % set profiles signaling sipCauseCodeMapping cpcToSipCauseMapProfile <profile_name> baseProfile defaultCpcSip causeMap 161 sipCause 503

  
  Command Example:

  % set profiles signaling sipCauseCodeMapping cpcToSipCauseMapProfile TEST baseProfile defaultCpcSip causeMap 161 sipCause 503

• Associate the cpcSipCauseMappingProfile used in the previous step with signaling causeCodeMapping.
  Command Syntax:

  % set addressContext default zone <zone_name> sipTrunkGroup <ingress_trunk_group> signaling causeCodeMapping cpcSipCauseMappingProfile <profile_name>

  
  Command Example:

  % set addressContext default zone ZONE1 sipTrunkGroup INGRESS_TG signaling causeCodeMapping cpcSipCauseMappingProfile TEST

Command Syntax

• Configure the queueLength for callQueuing at a global level.

  % set global callQueuing queueLength <1-4096>

• Configure the Call Admission Control (cac) for callLimit and hpcOverSubscription restrictions.

  % set addressContext default zone <INTERNAL_ZONE> sipTrunkGroup <Ingress_TG | Egress_TG>
  	cac
  		callLimit <0-2147483647> 
  		hpcOversubscription <0-100>

• Configure the queue for the hpcCallProfile.

  % set profile services hpcCallProfile <hpc_call_profile>
  	queue
  		length <1-256>
  		timeout <1-90>
  		state <disabled | enabled>

• Attach the configured hpcCallProfile with ingress or egress trunk group.

  % set addressContext default zone <INTERNAL_ZONE> sipTrunkGroup <Ingress_TG | Egress_TG>
  	services
  		hpcCallProfile <hpc_call_profile>

Relevant GETS parameters

Table 4: queue Parameters

Table 5: callQueuing Parameters

Command Example

The following example are applicable for both ingress and egress trunk groups:

% set global callQueuing queueLength <1-4096>
% commit

% set addressContext default zone INTERNAL sipTrunkGroup Ingress_TG cac callLimit 1 hpcOversubscription 100
% commit

% set addressContext default zone EXTERNAL sipTrunkGroup Egress_TG cac callLimit 1 hpcOversubscription 100
% commit

% set profile services hpcCallProfile test_hpc_call_profile queue length 50 timeout 10 state enabled
% commit

% set addressContext default zone INTERNAL sipTrunkGroup Ingress_TG services hpcCallProfile test_hpc_call_profile
% commit

% set addressContext default zone EXTERNAL sipTrunkGroup Egress_TG services hpcCallProfile test_hpc_call_profile
% commit

Configure rph etsDefaultValue

Command Syntax

• Configure the rph etsDefaultValue for the hpcCallProfile to be associated with ingress SIP TG.

  % set profiles services hpcCallProfile <hpcCallProfile_ingress>
  	rph etsDefaultValue <0-4>

• Enable the hpcCallProfile associated with the ingress SIP TG.

  % set profiles services hpcCallProfile <hpcCallProfile_ingress>
  	state <disabled | enabled>

• Associate the hpcCallProfile with the ingress SIP TG.

  % set addressContext <address_context> zone <ingress_zone> sipTrunkGroup <ingress_sip_tg>
  	services
  		hpcCallProfile <hpcCallProfile_ingress>

• Configure the rph etsDefaultValue for the hpcCallProfile to be associated with egress SIP TG.

  % % set profiles services hpcCallProfile <hpcCallProfile_egress> rph etsDefaultValue <0-4>

• Enable the hpcCallProfile associated with the egress SIP TG.

  % set profiles services hpcCallProfile <hpcCallProfile_egress>
  	state <disabled | enabled>

• Associate the hpcCallProfile with the egress SIP TG.

  % set addressContext default zone <ingress_zone> sipTrunkGroup <egress_sip_tg>
  	services
  		hpcCallProfile <hpcCallProfile_egress>

Command Example

% set profiles services hpcCallProfile HPC_INGRESS rph etsDefaultValue 2
% commit

% set profiles services hpcCallProfile HPC_INGRESS state enabled
% commit

% set addressContext default zone INTERNAL sipTrunkGroup INGRESS_TG services hpcCallProfile HPC_INGRESS
% commit

% set profiles services hpcCallProfile HPC_EGRESS rph etsDefaultValue 3
% commit

% set profiles services hpcCallProfile HPC_EGRESS state enabled
% commit

% set addressContext default zone EXTERNAL sipTrunkGroup EGRESS_TG services hpcCallProfile HPC_EGRESS
% commit

Configure getsStrings

Ribbon supports three types of GETS strings:

• accessNumber an
• featureCode fc
• numberTranslation nt

You can configure the SBC for matching any of supported GETS string values with the received string. The following table describes the maximum number of configurations allowed for the supported GETS string types.

Configure accessNumber an

Command Syntax

% set profiles service hpcCallProfile <hpcCallProfile_ingress>
	getsStrings
		accessNumber an <3-10 digit number>

Command Example

% set profiles service hpcCallProfile HPC_INGRESS getsStrings accessNumber an 7106274387
% commit

Configure featureCode fc

Command Syntax

% set profiles service hpcCallProfile <hpcCallProfile_ingress>
	getsStrings
		featureCode fc <3-10 characters without visual separators>

Command Example

% set profiles service hpcCallProfile HPC_INGRESS getsStrings featureCode fc *272
% commit

Configure numberTranslation nt

Command Syntax

% set profiles service hpcCallProfile <hpcCallProfile_ingress>
	getsStrings
		numberTranslation nt <3-10 digit number>

Command Example

% set profiles service hpcCallProfile HPC_INGRESS getsStrings numberTranslation nt 7102001234
% commit

Display hpcCallProfile

 Command Example

% show profiles services hpcCallProfile testHpcProfile
 
state     enabled;
rph {
    ingress {
        invalidEtsWps reject;
        validEtsWps   accept;
        nonEtsWps     ignore;
    }
    egress {
        validEtsWps dontInclude;
        nonEtsWps   include;
    }
}
getsStrings {
    featureCode {
        fc *272;
    }
    accessNumber {
        an 7106274387;
    }
    numberTranslation {
        nt 7102001234;
    }
}
queue {
    state   enabled;
    length  50;
    timeout 60;
}
dscp {
    egress {
        useRecvdValue enabled;
    }
}
dscpValue 50;

PSX Configuration

For information on PSX configuration, refer to the following pages:

• Provisioning GETS for NS-EP
• SCIP NS-EP Priority Services

EMS Configuration

For information on NW-HPC license, refer to the page Licensed Applications and Features.