Show Status System

In this section:

Common Call Statistics Terminology
Stable Calls	Calls that are established and fully stable (connected and media cut-through type of calls) and will survive a fail-over. This excludes calls in establishing, clearing and updating states which will not survive a fail-over.
Active Calls	A snapshot of total number of active calls on the SBC at the point of execution of the status command. This count reflects the actual live calls on the box independent of the state of the call (setup, stable, updating or clearing).
Call Attempts	Accumulative number of attempted calls on this system since the last reboot/start-up, including calls where a setup was sent/received, uncompleted calls (calls failed, busy, not answered, etc.) and calls completed (answered).
Call Completions	Accumulative number of calls completed on this system since the last reboot/start-up.

The SBC allows the operator to access data from the current interval and from the interval statistics table related to each object being monitored. The current interval consists of a statistics table entry that is accumulating data for the next interval report. The interval statistics table is a series of statistics table entries containing data from the most recently completed n intervals (where n is the number of intervals in the retention policy configuration).

Note

Refer to Links to Statistics Pages to navigate to a particular EMA or CLI statistics page.

Below is a high-level view of the command syntax for 'show status system' command.

Command Syntax

> show status system
	announcements
	baseMacAddress
	coredumpList
	coredumpSummary
	cpuUtilCurrentStatistics
	cpuUtilIntervalStatistics
	daughterBoardStatus
	dsbc
	dspRes
	dspStatus
	ethernetPort
	fanStatus
	fileStatisticsStatus
	fipsFSMState
	haConfig
	hardDiskStatus
	hardDiskUsage
	highAvailabilityPort
	ipPolicing
	jsrcServer
	ledStatus
	licenseInfo
	licenseStatus
	logicalMgmtIpInterfaceStatus
	mediaProfile
	memoryUtilCurrentStatistics
	memoryUtilIntervalStatistics
	mgmtIpInterfaceGroup
	ntp
	policyServer
	powerSupplyStatus
	savedConfigList
	security
	serverSoftwareUpgradeStatus
	serverStatus
	softwareUpgradeStatus
	syncStatus
	systemCongestionCurrentStatistics
	systemCongestionIntervalStatistics
	systemCongestionStatus

Command Parameters

The following objects are included in this table for completeness, but only apply when using the

show table system

command:

admin, congestion, daughterBoardAdmin, dspPad, fileStatisticsAdmin, fipsBypassMode, intervalStatistics, logicalMgmtIpInterfaceStatus, macAddressStatus, media, mgmtStaticRoute, serverAdmin

MultiExcerpt named SharedParameters was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro

MultiExcerpt named EthernetPort was not found -- Please check the page name and MultiExcerpt name used in the MultiExcerpt-Include macro

IP Policing uFlowStats Fields

The following fields display when using

uFlow Index – Index number of this uFlow statistic
Source IP Address – Source IP address
Destination IP Address – Destination IP address
Source IP Port – Source IP port
IP Protocol – IP protocol
LIF Group Id – LIF group ID
Policer Mode – The Policer mode
Policer Bucket Size – Number of packets allowed in the Policer bucket
Policer Credit Rate – Packet fill rate (packets per second)
Agg Policer – The name of the aggregate policer
Agg Policer Priority – Aggregate policer priority level
Packet Accept – The number of packets accepted by the policer
Packet Discard – Number of packets discarded by the policer
Byte Accept – The number of bytes accepted by the policer

IP Policing System Current and Interval

The following table lists systemCurStats and systemIntStats fields. The systemIntStats command results include the following additional attributes:

number – The interval sequence number. The number of intervals to store are configurable. Refer to Interval Statistics - CLI for configuration details.
intervalValid – A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
time – The system up time when the interval statisitic is collected for the specified interval.

Note

Complete IP Policing information related to threshold levels and duration is available at IP Policing Alarm Profile - CLI.

IP Policing System Current and Interval Attributes

Attribute	Description
`aclAcceptPacketCount`	The number of accepted packets for the access control list policer.
`aclDiscardPacketCount`	The number of discarded packets for the access control list policer.
`aclMajorAlarmCount`	The number of major alarms for the access control list policer.
`aclMajorAlarmDuration`	The duration of the major alarms in seconds for the access control list policer.
`aclMinorAlarmCount`	The number of minor alarms for the access control list policer.
`aclMinorAlarmDuration`	The duration of the minor alarms in seconds for the access control list policer.
`aclPeakDiscardRate`	The peak discard rate for the access control list policer.
`aggregateAcceptPacketCount`	The number of accepted packets for the aggregate policer.
`aggregateDiscardPacketCount`	The number of discarded packets for the aggregate policer.
`aggregateMajorAlarmCount`	The number of major alarms for the aggregate policer.
`aggregateMajorAlarmDuration`	The duration of the major alarms in seconds for the aggregate policer.
`aggregateMinorAlarmCount`	The number of minor alarms for the aggregate policer.
`aggregateMinorAlarmDuration`	The duration of the minor alarms in seconds for the aggregate policer.
`aggregatePeakDiscardRate`	The peak discard rate for the aggregate policer.
`arpAcceptPacketCount`	The number of accepted packets for the ARP policer.
`arpDiscardPacketCount`	The number of discarded packets for the ARP policer.
`arpMajorAlarmCount`	The number of major alarms for the ARP policer.
`arpMajorAlarmDuration`	The duration of the major alarms in seconds for the ARP policer.
`arpMinorAlarmCount`	The number of minor alarms for the ARP policer.
`arpMinorAlarmDuration`	The duration of the minor alarms in seconds for the ARP policer.
`arpPeakDiscardRate`	The peak discard rate for the ARP policer.
`badEtherIpHdrDiscardPacketCount`	The number of discarded packets for the bad Ethernet/IP Header policer.
`badEtherIpHdrMajorAlarmCount`	The number of major alarms for the bad Ethernet/IP Header policer.
`badEtherIpHdrMajorAlarmDuration`	The duration of the major alarms in seconds for the bad Ethernet/IP Header policer.
`badEtherIpHdrMinorAlarmCount`	The number of minor alarms for the bad Ethernet/IP Header policer.
`badEtherIpHdrMinorAlarmDuration`	The duration of the minor alarms in seconds for the bad Ethernet/IP Header policer.
`badEtherIpHdrPeakDiscardRate`	The peak discard rate for the bad Ethernet/IP Header policer.
`discardRuleDiscardPacketCount`	The number of discarded packets for the discard rule, plus the number of packets that do no match any ACL rule.
`discardRuleMajorAlarmCount`	The number of major alarms for the discard rule.
`discardRuleMajorAlarmDuration`	The duration of the major alarms in seconds discard rule.
`discardRuleMinorAlarmCount`	The number of minor alarms for the discard rule.
`discardRuleMinorAlarmDuration`	The duration of the minor alarms in seconds for the discard rule.
`discardRulePeakDiscardRate`	The peak discard rate for the discard rule.
`ipSecDecryptAcceptPacketCount`	The number of accepted packets for the IPsec Decrypt policer.
`ipSecDecryptDiscardPacketCount`	The number of discarded packets for the IPsec Decrypt policer.
`ipSecDecryptMajorAlarmCount`	The number of major alarms for the IPsec Decrypt policer.
`ipSecDecryptMajorAlarmDuration`	The duration of the major alarms in seconds for the IPsec Decrypt policer.
`ipSecDecryptMinorAlarmCount`	The number of minor alarms for the IPsec Decrypt policer.
`ipSecDecryptMinorAlarmDuration`	The duration of the minor alarms in seconds for the IPsec Decrypt policer.
`ipSecDecryptPeakDiscardRate`	The peak discard rate for the IPsec Decrypt policer.
`mediaAcceptPacketCount`	The number of accepted packets for the media policer.
`mediaDiscardPacketCount`	The number of discarded packets for the media policer.
`mediaMajorAlarmCount`	The number of major alarms for the media policer.
`mediaMajorAlarmDuration`	The duration of the major alarms in seconds for the media policer.
`mediaMinorAlarmCount`	The number of minor alarms for the media policer.
`mediaMinorAlarmDuration`	The duration of the minor alarms in seconds for the media policer.
`mediaPeakDiscardRate`	The peak discard rate for the media policer.
`rogueMediaDiscardPacketCount`	The number of discarded packets for the rogue media policer.
`rogueMediaMajorAlarmCount`	The number of major alarms for the rogue media policer.
`rogueMediaMajorAlarmDuration`	The duration of the major alarms in seconds for the rogue media policer.
`rogueMediaMinorAlarmCount`	The number of minor alarms for the rogue media policer.
`rogueMediaMinorAlarmDuration`	The duration of the minor alarms in seconds for the rogue media policer.
`rogueMediaPeakDiscardRate`	The peak discard rate for the rogue media policer.
`srtpDecryptDiscardPacketCount`	The current number of packets discarded by SRTP decrypt discards.
`srtpDecryptMajorAlarmCount`	The current number of major alarms for the SRTP decrypt discards.
`srtpDecryptMajorAlarmDuration`	The current duration of the major alarms in seconds for the SRTP decrypt discards.
`srtpDecryptMinorAlarmCount`	The current number of minor alarms for SRTP decrypt discards.
`srtpDecryptMinorAlarmDuration`	The current duration of the minor alarms in seconds for the SRTP decrypt discards.
`srtpDecryptPeakDiscardRate`	The current peak discard rate for SRTP decrypt discards.
`systemName`	The SBC system name.
`uFlowAcceptPacketCount`	The number of accepted packets for the micro flow policer.
`uFlowDiscardPacketCount`	The number of discarded packets for the micro flow policer.
`uFlowMajorAlarmCount`	The number of major alarms for the micro flow policer.
`uFlowMajorAlarmDuration`	The duration of the major alarms in seconds for the micro flow policer.
`uFlowMinorAlarmCount`	The number of minor alarms for the micro flow policer.
`uFlowMinorAlarmDuration`	The duration of the minor alarms in seconds for the micro flow policer.
`uFlowPeakDiscardRate`	The peak discard rate for the micro flow policer.

Command Examples

To view announcements memory usage:

show status system announcements memoryUsage
memoryUsage ASTON {
    totalSegments       67;
    cachedSegments      66;
    totalCacheMemory    "125819520 bytes";
    usedCacheMemory     "1920000 bytes";
    utilizedCacheMemory 1%;
    totalPlayoutTime    "0h: 3m: 52s";
}
[ok][2013-12-20 01:30:41]

To view base MAC address:

show status system baseMacAddress
baseMacAddress TUNAA {
    assignedBaseAddress 00:10:6b:03:c9:22;
    activeBaseAddress   00:10:6b:03:c9:22;
}

To view coredump list:

show status system coredumpList
coredumpList Bison1 1 {
    coredumpFileName  core.1.CE_2N_Comp_Pipe.1383109457;
    size              "143292 KBytes";
    dateAndTime       "Wed Oct 30 01:04:17 2013";
    newSinceLastStart true;
}
coredumpList Bison1 2 {
    coredumpFileName  core.1.CE_2N_Comp_CpxA.1383109455;
    size              "94620 KBytes";
    dateAndTime       "Wed Oct 30 01:04:16 2013";
    newSinceLastStart true;
}
coredumpList Bison1 3 {
    coredumpFileName  core.1.CE_2N_Comp_EnmP.1383109456;
    size              "118556 KBytes";
    dateAndTime       "Wed Oct 30 01:04:16 2013";
    newSinceLastStart true;
}
coredumpList Bison1 4 {
    coredumpFileName  core.1.CE_2N_Comp_NimP.1383109456;
    size              "81848 KBytes";
    dateAndTime       "Wed Oct 30 01:04:16 2013";
    newSinceLastStart true;
}
coredumpList Bison1 5 {
    coredumpFileName  core.1.CE_2N_Comp_PesP.1383109456;
    size              "389796 KBytes";
    dateAndTime       "Wed Oct 30 01:04:16 2013";
    newSinceLastStart true;
}
coredumpList Bison1 6 {
    coredumpFileName  core.1.CE_2N_Comp_Scpa.1383109456;
    size              "217252 KBytes";
    dateAndTime       "Wed Oct 30 01:04:16 2013";
    newSinceLastStart true;
}
coredumpList Bison1 7 {
    coredumpFileName  core.1.CE_2N_Comp_SmPr.1383109456;
    size              "118396 KBytes";
    dateAndTime       "Wed Oct 30 01:04:16 2013";
    newSinceLastStart true;
}

To view Daughterboard status (SBC 7000 example is below):

show status system daughterBoardStatus 
daughterBoardStatus bf024.eng.sonusnet.com 1 {
    daughterBoardId       FRU_DSP1;
    present               true;
    productName           DSPLB;
    serialNum             4145130005;
    partNum               811-41600;
    operationalStatus     enabled;
    imageLoadFailureCount 0;
    fpgaVersion           "";
}
daughterBoardStatus bf024.eng.sonusnet.com 2 {
    daughterBoardId       FRU_DSP2;
    present               true;
    productName           DSPLB;
    serialNum             4132130005;
    partNum               811-41600;
    operationalStatus     enabled;
    imageLoadFailureCount 0;
    fpgaVersion           "";
}
daughterBoardStatus bf024.eng.sonusnet.com 3 {
    daughterBoardId       FRU_DSP3;
    present               true;
    productName           DSPLB;
    serialNum             4145130010;
    partNum               811-41600;
    operationalStatus     enabled;
    imageLoadFailureCount 0;
    fpgaVersion           "";
}
daughterBoardStatus bf024.eng.sonusnet.com 4 {
    daughterBoardId       FRU_DSP4;
    present               true;
    productName           DSPLB;
    serialNum             4145130002;
    partNum               811-41600;
    operationalStatus     enabled;
    imageLoadFailureCount 0;
    fpgaVersion           "";

To view DSP usage:

This example includes several results in the form of <codec>V8Total or <codec>V8Utilization. These entries apply if you allowed support for T.38 version 3 (also called V.34 fax transcoding). If you enabled T.38 version 3, you must enable a V.8 signaling detector for all voice codecs.

show status system dspStatus dspUsage

dspUsage sbx20 {
    slot1ResourcesUtilized   0;
    slot2ResourcesUtilized   0;
    slot3ResourcesUtilized   0;
    slot4ResourcesUtilized   0;
    compressionTotal         10272;
    compressionAvailable     10272;
    compressionUtilization   0;
    compressionAllocFailures 0;
    g711Total                10272;
    g711Utilization          0;
    g711SsTotal              8544;
    g711SsUtilization        0;
    g726Total                5760;
    g726Utilization          0;
    g7231Total               5760;
    g7231Utilization         0;
    g722Total                5760;
    g722Utilization          0;
    g7221Total               4992;
    g7221Utilization         0;
    g729AbTotal              5184;
    g729AbUtilization        0;
    ecmTotal                 4800;
    ecmUtilization           0;
    ilbcTotal                3648;
    ilbcUtilization          0;
    amrNbTotal               4224;
    amrNbUtilization         0;
    amrWbTotal               2304;
    amrWbUtilization         0;
    evrcb0Total              2304;
    evrcb0Utilization        0;
    evrc0Total               3168;
    evrc0Utilization         0;
    toneTotal                0;
    toneAvailable            0;
    toneUtilization          0;
    toneAllocFailures        0;
    efrTotal                 4224;
    efrUtilization           0;
    g711V8Total              7104;
    g711V8Utilization        0;
    g711SsV8Total            6240;
    g711SsV8Utilization      0;
    g726V8Total              4608;
    g726V8Utilization        0;
    g7231V8Total             4608;
    g7231V8Utilization       0;
    g722V8Total              4608;
    g722V8Utilization        0;
    g7221V8Total             4128;
    g7221V8Utilization       0;
    g729AbV8Total            4224;
    g729AbV8Utilization      0;
    ecmV34Total              1344;
    ecmV34Utilization        0;
    ilbcV8Total              3072;
    ilbcV8Utilization        0;
    opusTotal                0;
    opusUtilization          0;
}

To view Ethernet Port packet statistics:

show status system ethernetPort packetStatistics
packetStatistics pkt0 {
    rxPackets 39014;
    txPackets 238436;
    rxErrors  0;
    txErrors  0;
    rxDropped 0;
    txDropped 0;
}
packetStatistics pkt1 {
    rxPackets 939246;
    txPackets 1195538;
    rxErrors  0;
    txErrors  0;
    rxDropped 0;
    txDropped 0;
}
packetStatistics pkt2 {
    rxPackets 0;
    txPackets 234;
    rxErrors  0;
    txErrors  0;
    rxDropped 0;
    txDropped 0;
}
packetStatistics pkt3 {
    rxPackets 0;
    txPackets 234;
    rxErrors  0;
    txErrors  0;
    rxDropped 0;
    txDropped 0;
}

To view hard disk usage:

show status system hardDiskUsage
hardDiskUsage HEBBE / {
    totalDiskSpace "148439472 KBytes";
    freeDiskSpace  "122077592 KBytes";
    usedDiskSpace  18%;
    role           primary;
    syncStatus     unprotected;
    syncCompletion n/a;
}
hardDiskUsage HEBBE /var/log/sonus/sbx/evlog {
    totalDiskSpace "96117568 KBytes";
    freeDiskSpace  "90977952 KBytes";
    usedDiskSpace  5%;
    role           primary;
    syncStatus     unknown;
    syncCompletion n/a;
}

To view systemCongestionIntervalStatistics:

show status system systemCongestionIntervalStatistics
systemCongestionIntervalStatistics 4309 entry {
    intervalValid         true;
    time                  8013385;
    levelMC1Count         0;
    levelMC1TotalTime     0;
    levelMC2Count         0;
    levelMC2TotalTime     0;
    levelMC3Count         0;
    levelMC3TotalTime     0;
    overloadRejects       0;
    avgCallRate           0;
    peakCallRate          0;
    callArrivals          0;
    emergencyCallArrivals 0;
    emergencyCallRejects  0;
    sipRegArrivals        0;
    sipRegRejects         0;
    avgRegRate            0;
    peakRegRate           0;
}
systemCongestionIntervalStatistics 4310 entry {
    intervalValid         true;
    time                  8014285;
    levelMC1Count         0;
    levelMC1TotalTime     0;
    levelMC2Count         0;
    levelMC2TotalTime     0;
    levelMC3Count         0;
    levelMC3TotalTime     0;
    overloadRejects       0;
    avgCallRate           0;
    peakCallRate          0;
    callArrivals          0;
    emergencyCallArrivals 0;
    emergencyCallRejects  0;
    sipRegArrivals        0;
    sipRegRejects         0;
    avgRegRate            0;
    peakRegRate           0;
}
systemCongestionIntervalStatistics 4311 entry {
    intervalValid         true;
    time                  8015185;
    levelMC1Count         0;
    levelMC1TotalTime     0;
    levelMC2Count         0;
    levelMC2TotalTime     0;
    levelMC3Count         0;
    levelMC3TotalTime     0;
    overloadRejects       0;
    avgCallRate           0;
    peakCallRate          0;
    callArrivals          0;
    emergencyCallArrivals 0;
    emergencyCallRejects  0;
    sipRegArrivals        0;
    sipRegRejects         0;
    avgRegRate            0;
    peakRegRate           0;
}
systemCongestionIntervalStatistics 4312 entry {
    intervalValid         true;
    time                  8016085;
    levelMC1Count         0;
    levelMC1TotalTime     0;
    levelMC2Count         0;
    levelMC2TotalTime     0;
    levelMC3Count         0;
    levelMC3TotalTime     0;
    overloadRejects       0;
    avgCallRate           0;
    peakCallRate          0;
    callArrivals          0;
    emergencyCallArrivals 0;
    emergencyCallRejects  0;
    sipRegArrivals        0;
    sipRegRejects         0;
    avgRegRate            0;
    peakRegRate           0;
}

To view system congestion status details.

show status system systemCongestionStatus
systemCongestionStatus entry {
    systemCongestionMCLevel           0;
    systemCongestionCPULevel          0;
    systemCongestionMemLevel          0;
    systemCongestionCallRateLevel     0;
    systemCongestionIRTTLevel         0;
    systemCongestionMCDuration        217339;
    systemCongestionCallArrivalRate   0;
    systemCongestionCallAcceptRate    100;
    systemCongestionCallAcceptCount   65535;
    systemCongestionCallEqArrivalRate 198;
    systemCongestionRegArrivalRate    0;
    systemCongestionSubsArrivalRate   792;
}

To view system congestion current statistics.

show status system systemCongestionCurrentStatistics
systemCongestionCurrentStatistics entry {
    levelMC1Count         0;
    levelMC1TotalTime     0;
    levelMC2Count         0;
    levelMC2TotalTime     0;
    levelMC3Count         0;
    levelMC3TotalTime     0;
    overloadRejects       0;
    avgCallRate           0;
    peakCallRate          0;
    callArrivals          0;
    emergencyCallArrivals 0;
    emergencyCallRejects  0;
    sipRegArrivals        0;
    sipRegRejects         0;
    avgRegRate            0;
    peakRegRate           0;
    maxActiveCalls        0;
    sipSubsArrivals       144509;
    sipSubsRejects        0;
    avgSubsRate           305;
    peakSubsRate          803;
}

To view Micro Flow stats:

show status system ipPolicing uFlowStats
uFlowStats 1 {
    sourceIpAddress      10.10.10.10;
    destinationIpAddress 10.11.12.13;
    sourceIpPort         45506;
    ipProtocol           udp;
    lifGrpId             2;
    policerMode          PktRate;
    policerBucketSize    50;
    policerCreditRate    1023;
    aggPolicer           "ZONE AGG";
    aggPolicerPriority   1;
    packetAccept         1;
    packetDiscard        0;
    byteAccept           527;
}

To display the current HA configuration settings:

show status system haConfig
haConfig SBC01 {
    leaderElection standard;
    bondMonitoring direct-connect;
}

To display the D-SBC Sig Port statistics:

show status system dsbc dsbcSigPortStatistics
dsbcSigPortStatistics 10.3.0.87 {
    State         outOfService;
    Interface     ip;
    BytesSent     0;
    PdusSent      0;
    BytesReceived 0;
    PdusReceived  0;
}

To display sync status of active and standby nodes created through a N:1 redundancy group:

admin@msbcActive1> show status system syncStatus
"Metavar Data" {
    status syncCompleted;
}
"Call/Registration Data" {
    status syncCompleted;
}
 
 
admin@msbcStandby> show status system syncStatus
"Metavar Data" {
    status unprotectedRunningStandby;
}
"Call/Registration Data" {
    status unprotectedRunningStandby;
}

Space shortcuts

Page tree

Command Syntax

Command Parameters

IP Policing uFlowStats Fields

IP Policing System Current and Interval

Command Examples