Show Status System

admin

Basic configuration (name, location, etc) for the system. See Admin Attributes table below for details.

announcements

Announcement file status and statistics. See Announcements Attributes table below for details.

baseMacAddress

Displays base MAC address of servers.

• activeBaseAddress – The base MAC address assigned to the active server.
• assignedBaseAddress – The base MAC address assigned to this server.

Displays cluster-specific configuration details.

• mgmtInterfaceGroup – The Management Interface Group used for intra-cluster communication
• mgmtIpAddress – The management IP address used for intra-cluster communication
• type – The interface type used during intra-cluster communication

congestion

System congestion profile for the node.

• adaptive – adaptive overload configuration.
• levelMC1 – Configuration for congestion level MC1.
• levelMC2 – Configuration for congestion level MC2.
• levelMC3 – Configuration for congestion level MC3.
• mode – Mode (static or adaptive) of the system overload control.
• policer – System congestion Call Rate Policer configuration.

coredumpList

List of core dumps on the server(s). Fields include:

• coredumpFileName
• size
• dateAndTime
• newSinceLastStart (true/false)

coredumpSummary

Summary of core dump files on server(s).

• <server name> – The name of the server.
• coredumpAndTraceCount – Number of coredumps and trace files.
• totalSize – Indicates the total size of the coredumps (KBytes).

(Available only on SWe except ssbc SWe)

<system name> – The SBC system name.

• amrNbTotal – Total AMR–NB resource capacity on this server.

• amrNbUtilization – Percentage utilization of AMR–NB resources on this server.

• amrWbTotal – Total AMR–WB resource capacity on this server.

• amrWbUtilization – Percentage utilization of AMR–WB resources on this server.
• compressionAllocFailures – Running count of resource allocation failures due to resource exhaustion.
• compressionAvailable – Actual compression resources currently available in real time. This essentially equates to the total number of G.711 resources after loading.
• compressionTotal – Maximum number of compression resources on the server (i.e. before loading, so this number is static). This essentially equates to the total number of G.711 resources before loading (i.e. lightest codec).

• compressionUtilization – Percentage of compression resources in use (accounting for various codec weights). This can be calculated using the formula (compressionTotal – compressionAvailable) / compressionTotal.
  NOTE: Use this value when determining the extent of DSP module load (regardless of codec type).

• ecmTotal – Total T.38 ECM resource capacity on this server.
• ecmUtilization – Percentage utilization of T.38 ECM resources on this server.
• ecmV34Total – Total T.38 ECM V.34 resource capacity on this server.
• ecmV34Utilization – Percentage utilization of T.38 ECM V.34 resources on this server.
• efrTotal – Total EFR resource capacity on this server.
• efrUtilization – Percentage utilization of EFR resources on this server.
• evrc0Total – Total EVRC0 resource capacity on this server.
• evrc0Utilization – Percentage utilization of EVRC0 resources on this server.
• evrcb0Total – Total EVRCB0 resource capacity on this server.
• evrcb0Utilization – Percentage utilization of EVRCB0 resources on this server.
• g711SsTotal – Total G711SS (silence suppression) resource capacity on this server.

• g711SsUtilization – Percentage utilization of G711SS (silence suppression) resources on this server.

• g711Total – Total G711 resource capacity on this server.

• g711Utilization – Percentage utilization of G711 resources on this server.
  NOTE: The g711Utilization includes g711 channels in use plus channels that are reserved but not activated as part of the call set up process.  In this case, ensure to reserve enough resources to account for the worst case codec. For example, in release 4.2.x, a reserved channel is about 4.5 times as expensive as a G.711 channel. 

• g711V8Total – Total G711 V8 resource capacity on this server.

• g711V8Utilization – Percentage utilization of G711 V8 resources on this server.

• g722Total – Total G.722 resource capacity on this server.
• g722Utilization – Percentage utilization of G.722 resources on this server.

• g722V8Total – Total G.722 V8 resource capacity on this server.

• g722V8Utilization – Percentage utilization of G.722 V8 resources on this server.

• g726Total – Total G726 resource capacity on this server.
• g726Utilization –  Percentage utilization of G726 resources on this server.

• g726V8Total – Total G726 V8 resource capacity on this server.

• g726V8Utilization – Percentage utilization of G726 V8 resources on this server.

• g729AbTotal – Total G729A+B resource capacity on this server.
• g729AbUtilization – Percentage utilization of G729A+B resources on this server.

• g729AbV8Total – Total G729A+B V8 resource capacity on this server.

• g729AbV8Utilization – Percentage utilization of G729A+B V8 resources on this server.

• g7221Total – Total G.722.1 resource capacity on this server.
• g7221Utilization – Percentage utilization of G.722.1 resources on this server.

• g7221V8Total – Total G.722.1 V8 resource capacity on this server.

• g7221V8Utilization – Percentage utilization of G.722.1 V8 resources on this server.

• g7231Total – Total G723.1 resource capacity on this server.
• g7231Utilization – Percentage utilization of G7231 resources on this server.

• g7231V8Total – Total G723.1 V8 resource capacity on this server.

• g7231V8Utilization – Percentage utilization of G7231 V8 resources on this server.

• ilbcTotal – Total iLBC resource capacity on this server.
• ilbcUtilization – Percentage utilization of iLBC resources on this server.

• ilbcV8Total – Total iLBC V8 resource capacity on this server.

• ilbcV8Utilization – Percentage utilization of iLBC V8 resources on this server.

• opusTotal – Total OPUS resource capacity on this server.

• opusUtilization – Percentage utilization of OPUS resources on this server.

• toneAllocFailures – Percentage of tone resource allocation failures on this server.
• toneAvailable – Number of tone resources currently unused and available on this server.
• toneTotal – Total tone resource capacity on this server.
• toneUtilization – Percentage utilization of tone resources on this server.

cpuUtilCurrentStatistics

The CPU utilization of the server for the current period.

• <server name> – The name of the server.
• average – The average CPU % utilization for this interval.
• high – The high CPU % utilization for this interval.
• low – The low CPU % utilization for this interval.

cpuUtilIntervalStatistics

The CPU utilization for the 'n' number of intervals.

• number – The interval sequence number. The number of intervals to store are configurable. (Refer to Interval Statistics - CLI for status/statistics details)
• ceName – The SBC server name.
• cpu – The CPU number.
• intervalValid – A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
• time – The system up time when the interval statistics are collected.
• average – The average CPU % utilization for this interval.
• high – The high CPU % utilization for this interval.
• low – The low CPU % utilization for this interval.

Displays SBC database sync status from executing the request system admin <system name> verifyDatabaseIntegrity command. (Refer to Admin - CLI)

The following command options are available to match the results of the 'show' command with the associated 'request' command:

activeAndStandbyPolicy – Display results of the sync check against policy databases on the active and standby servers.
activeConfigAndActivePolicy – Displays the results of the sync check against the policy and configuration databases on the active server.

Displayed results include the following fields:

• syncModuleName – The database sync module name: activeAndStandbyPolicy, activeConfigAndActivePolicy
• syncStatus – Possible results: inProgress, inSync, outOfSync, unknown.
• timeStamp – Times tamp of when the command was executed.

daughterBoardAdmin

SBC 5x10/7000 daughter board administrative status from server/CE level.

• ceName – The SBC server name.
• disableCleanupAction – Identifies the type of disable cleanup action (forced/graceful)
• dryUpTime – The set time, in minutes, for a graceful shutdown to occur (range: 0-60 / default = 10).
• slot – Slot number designation for DSP20 (slot 1) and DSP25 (slots 1-4) cards.
• state – Administrative state of daughter board.

NOTE: Not applicable for 5x00 or SWe systems.

daughterBoardStatus

Server Daughter Board (DB) status details. See Daughter Board Status Attributes table below for details.

DoD mode status details, with following details:

• index – Index number
• status – Specifies if DoD mode is enabled/disabled, as well as if CLI, EMA Platform Mode and sFTP are enabled for access while SBC is in DoD mode.

D-SBC statistics details.

• dsbcSigPortStatistics – D-SBC Signaling Port statistics when communicating with the other D-SBC nodes. Fields include:
  • <IP address> – The IP address of the remote node
  • BytesReceived – The total number of signaling bytes received from this remote node
  • BytesSent – The total number of signaling bytes sent to this remote node
  • Interface – The interface used for this link
  • PdusReceived – The total number of signaling PDUS received from the remote node
  • PdusSent – The total number of signaling PDUS sent to the remote node
  • State – The current state of the signaling link of the remote node
• dsbcSigPortStatus – D-SBC Signaling Port status details.
  
  • <index> – The D-SBC Signaling Port index.
  • state – The administrative state of the D-SBC Signaling Port.

dspPad

DSP PAD configuration service (must be restarted for new configuration to take effect). See DSP PAD Attributes table for details (for 'show table system' command only).

dspRes

DSP historical interval statistics. See DSP Resources Attributes table below for parameter details.

• dspCallCurrentStatistics – The Sonus System Call DSP Resource Current table.
• dspCallIntervalStatistics – The Sonus System Call DSP Resource Interval table.
• dspUsageCurrentStatistics – The Sonus DSP Resource Current table.
• dspUsageIntervalStatistics – The Sonus DSP Resource Interval table.

dspStatus dspUsage

Status of DSP resources. See DSP Status Attributes table below for details.

ethernetPort

Configuration for management, packet, and field service Ethernet ports. See Ethernet Port Attributes table for details.

fanStatus

Fan status on the server(s).

• <system name>
• <fan nomenclature>
• speed

Displays whether the following interval statistics are enabled/disabled to write data to the statistics file.

• CallFailIntervalStats
• CallIntervalStats
• DiamNodeRfIntervalStatistics
• DnsGroupDnsServerStats
• DspResDspCallIntervalStats
• DspResDspUsageIntervalStats
• H323SigPortStatisticsStats
• IpAclOverallStats
• IpAclRuleStats
• IpPolicingSystemIntStats
• LinkDetectionGroupStats
• LinkMonitorStats
• MtrmConnPortPeerStats

• NBS5200TrunkGroupStatusStats
NOTE: This statistic applies to both SBC 5000 and 7000 series. The EMS uses "SBC7KTrunkGroupStatusStats" for SBC 7000 series statistics.

• SipIntervalStats
• sipOcsCallIntervalStatistics
• SipRegCountStats
• SipSigPortStatisticsStats
• SipSubCountStats
• SysCpuUtilIntStatsSts
• SysMemoryUtilIntStatsSts
• SystemCongestionIntervalStats
• TrafficControlStats
• ZoneIntervalStatisticsStats

fileStatisticsStatus

FIPS finite state machine state.

• issuer – FIPS FSM Issuer.
• message – FIPS FSM message.
• state – FIPS FSM state.
• timeStamp – FIPS FSM timestamp.

SWE only. Returns server name and GPU number for each attached GPU. See GPU Status table for details.

Returns GPU codec channel capacities. Available only on SBC SWe except S-SBC SWe. See GPU Transcode Status for details.

This statistic displays GRHA status details.

• serverName
• leaderElection – The current GRHA mode setting for the leader election algorithm type.
• bondMonitoring – The current GRHA mode setting for bond monitoring type.

hardDiskStatus

Hard disk status on the server(s).

• capacity – Capacity of the disk.
• diskLifeRemaining – A calculated percentage estimating the life remaining of the device or N/A if not supported by the device.
• diskStatus – Hard disk status that indicates if the disk is online/failed.
• healthTest – Pass or Fail indicating the overall health of the device.
• present – Indicates if the hard disk exists (true/false).
• productId – Product ID of the hard disk as assigned by vendor.
• revision – Revision of the hard disk as assigned by vendor  .

hardDiskUsage

Hard disk usage on the server(s).

• freeDiskSpace – Indicates free hard disk space (KBytes).
• role – Role of the server for the indicated partition (see Note below).
• syncCompletion – Indicates partition's sync completion percentage.
• syncStatus – Partition's synchronization status with peer server.
• totalDiskSpace – Capacity of the disk (KBytes).
• usedDiskSpace – Indicates used hard disk (%) .

NOTE: The role of the standby server is reflected as Primary for the root partition because the other partition, /var/log/sonus/sbx/evlog is not mirrored/mounted in the standby CE until a switch-over occurs and the Standby assumes the role of active.

highAvailabilityPort

Configuration and status for the HA ethernet ports.

• statistics – Lists status/statistics details such as port name, number of packets transmitted/received, bytes transmitted/received, and errors transmitted/received.
  • <host name> – SBC host name.
  • allocRxBufFailRx – The number of receive buffer allocation errors.
  • byteRx – The number of bytes received.
  • byteTx – The number of bytes transmitted.
  • crcErrRx – The number of receive CRC errors.
  • errTx – The number of transmit errors.
  • noBufCntRx – The number of receive no buffer errors.
  • overErrRx – The number of receive overrun errors.
  • packetRx – The number of packets received.
  • packetTx – The number of packets transmitted.
• status – List details such as port name, MAC address, IP address, negotiated speed and OOS reason.
  • ipAddress – The IP address of this port.
  • macAddress – The MAC address of this port.
  • negotiatedSpeed – The negotiated speed of this port.
  • oosReason – The reason this port is out of service.

intervalStatistics

The system- wide settings for interval statistics.

• maxFileRetentionPeriod – The maximum retention period for statistics files stored on disk. (range: 60-1440 / default = 60)
• nodeId – The EMS configured nodeID for this system to be used as part of the filename when writing the statistics  to the file. (default = 0)

• numOfPastIntervals – The maximum number of past intervals display in CLI. (range: 1-12 / default = 4)
• timeInterval – The time interval for interval statistics data.

ipPolicing

The MIB Module for IP Monitoring statistics. These statistics are divided into three categories: Offenders Lists statistics, Micro Flow statistics and System statistics.

• Role – Offenders list role
• Index – Index  number of this statistic
• Address Context – Address context associated with this statistic
• Interface Group Name – IP interface group name
• Interface Name – Interface name
• Source IP Address – Source IP address
• Destination IP Address – Destination IP address
• Source IP Port – Source IP port
• Destination IP Port – Destination IP port
• IP Protocol – IP protocol
• Ether Type – This field indicates the decimal value representing which protocol is encapsulated in the payload of the Ethernet Frame. For example, a value of 2048 equates to 0800 hexidecimal, which in turn represents IPv4.
• Discard Count – The number of packets dropped
• Ring Type
• Source Unique

Offenders Lists statistics (See Offenders List Details section for additional details)

• aclOffendersList – The table of statistics for the ACL policer offenders list
• aggregateOffendersList – The table of statistics for the aggregate policer offenders list
• arpOffendersList – The table of statistics for the ARP policer offenders list
• badEtherIpHdrOffendersList – The table of statistics for the bad Ethernet/IP Header policer offenders list
• discardRuleOffendersList – The table of statistics for the discard rule offenders list
• ipSecDecryptOffendersList – The table of statistics for the IPsec Decrypt policer offenders list
• mediaOffendersList – The table of statistics for the media policer offenders list
• rogueMediaOffendersList – The table of statistics for the rogue media policer offenders list
• uFlowOffendersList – The table of statistics for the micro flow policer offenders list

Micro Flow statistics:

• uFlowStats – The table of micro flow statistics. See IP Policing uFlowStats Fields for details

NOTE: This command displays any microflow entry regardless of whether SIPFE or MRM (or any sub-system) created the microflow.

System statistics:

• systemCurStats – The Sonus System Policer Current table. See IP Policing System Current and Interval Attributes table below for a list of attributes.
• systemIntStats – The Sonus System Policer Interval table. See IP Policing System Current and Interval Attributes table below for a list of attributes.

jsrcServer

JSRC server configuration.

• globalConfig – This defines global configuration applicable to all the JSRC servers.
• remoteServer – JSRC server configuration.
• serverStatus – JSRC server status.

ledStatus

Displays status of various LEDs of the server.

• ledColor – Indicates the LED color.
• ledState – Indicates the LED state.

Status details about each licensed feature. See License Attributes table for details.

licenseInfo

The license status for registered license features. See License Attributes table for details.

License details for the legacy licenses stored on the SBC. See License Attributes table for details.

Displays the licenseRequired configuration: The configured minimum and maximum number of licenses for a particular feature to request from the Site License Server (SLS) for the SBC application to use. See License Attributes table for details.

(Applies to 'show table' command only)

Displays status information about licenses acquired by the SBC application while operating in network license mode.

See License Attributes table for details.

Per-server license configuration. See License Attributes table for details.

(Applies to 'show table' command only)

License server status details. See License Attributes table for details.

licenseStatus

The CE license status table describes the current CE license state, for example "dualCe". See License Attributes table for details.

loadBalancingService

The Load Balancing Service status/statistics details with the following fields. See one of the following tables, as applicable, for details:

• Load Balancing Service Attributes (SBC 5xx0/7000/SWe)
• Load Balancing Service Attributes (S-SBC)
• Load Balancing Service Attributes (M-SBC)

logicalMgmtIpInterface

The logical management IP interface status/statistics details with following fields:

• name – The name of the logical IP interface.
• mgmtIpInterfaceGroupName
• ipAddress
• state

logicalMgmtIpInterfaceStatus 

The Logical Mgmt IP Interface status status/statistics details with following fields:

• name – The name of the logical IP interface.
• operStatus – Operational status.

Displays MAC addresses of the system server(s).

• <server name> – SBC server name.

• status – Status of the specified MAC address.

• usedBy – Name of the server using this MAC address.

• usedByPort – The port used by this MAC address.

media

System- wide media configurations, UDP port range and RTP/RTCP peer inactivity timeout.

• mediaPeerInactivity – media peer inactivity configurables.
• mediaPortRange – Allowed range of UDP port numbers for RTP/RTCP media.
• mediaRtcpControl – RTCP session configurables.

mediaProfile

DSP Media Profile configuration. (The System Media Profile configuration applies to hardware platforms (5000 series, 5400, 7000) only.)

• compression – Percentage (of DSP cores) for capability COMPRESSION.
• tone – Percentage (of DSP cores) for capability TONE.

memoryUtilCurrentStatistics

The memory utilization for the current interval period. Fields include:

• ceName – The SBC server name.
• average – The average memory % utilization for this interval.
• averageSwap – The average swap % memory utilization for this interval.
• high – The high memory % utilization for this interval.
• highSwap – The high swap % memory utilization for this interval.
• low – The low memory % utilization for this interval.
• lowSwap – The low swap memory % utilization for this interval.

memoryUtilIntervalStatistics

The memory utilization for the 'n' number of intervals.

• number – The interval sequence number. The number of intervals to store are configurable. Refer to Interval Statistics - CLI for status/statistics details.
• ceName – The SBC server name.
• average – The average memory % utilization for this interval.
• averageSwap – The average swap memory % utilization for this interval.
• high – The high memory % utilization for this interval.
• highSwap – The high swap memory % utilization for this interval.
• intervalValid – A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
• low – The low memory % utilization for this interval.
• lowSwap – The low swap memory % utilization for this interval.
• time – The system up time when the interval statistic is collected.

Displays the system dynamic metavariable names and values.

• ceName – Displays the name of the instance along with its HA IP address.
• name – Displays the name of the interface definition parameters.
• value – Displays the value associated with the IDP.

Displays user-configured metavariables that add to the metadata available to an existing SBC SWe cloud deployment.

• ceName – Displays the name of the instance along with its HA IP address.
• name – Displays the name of an interface definition parameter.
• value – Displays the value assigned to the specified parameter.

mgmtIpInterfaceGroup

A group of management IP interfaces for the default address context. See Mgmt IP Interface Group Parameters table below for details.

mgmtStaticRoute

Static IP routes for this address context.

• <destination IP address>
• preference – Route preference value.

NOTE: For internal debug use only.

Network Processor statistics details.See Network Processor Attributes table below for details.

ntp

NTP services management details. See NTP Attributes table below for details

Path for ICMP ping mechanism

• name – Path Check Path name
• sourceIpAddress – Source IP address of the ping path
• targetIpAddress – Target IP address of the ping path
• reportSignalIpAddress – Reported Signaling IP address of the ping path
• reportSignalIpPort – Reported Signaling Port of the ping path
• pathCheckProfile – Path Check profile name used when pinging this peer
• addressContext – Address Context where the corresponding Interface Group is present
• zone – Zone name used when pinging this peer
• ipInterfaceGroup – IP Interface Group where the corresponding IP Interface is present.
• ipInterface – IP interface from which ping should be generated.
• state – Administrative state of pathCheckPath (active pinging state).

NOTE: This field applies to the 'show table' command only.

policyServer

Softswitch servers and client services status/statistics details. See Policy Server Attributes table below for details.

powerSupplyStatus

Power consumption/state of the server.

• <server name>
• partNum – Identifies the part number of the module.
• powerFault – Indicates if there is power fault.
• present – Indicates if the module is present or not.
• productName – Identifies the name (as given by manufacturer) of power supply module.
• serialNum – Identifies the serial number of the power supply module.
• voltageFault – Indicates if there is voltage fault.

Displays the Redundancy Group status of the instances created through N:1 redundancy group.

NOTE: This command applies to N:1 redundancy configurations only.

savedConfigList

List of configurations saved on the system.

• <index of saved config. file>
• fileName – The file name of the saved configuration.
• size – Indicates size of the saved configuration file (KBytes).
• version – The software version name of the saved configuration.

Displays the personality role of the SBC SWe/SBC SWe Cloud instance. Choices are isbc, msbc and ssbc.

security

Security management status/statistics details. See Security Attributes table for details.

serverAdmin

The serverAdmin table describes the configuration of each server module.

• name – The node name.
• actualCeName
  • Cloud platform: The ceName provided in the user data.
  • Non-Cloud platform: The SBC name entered during the SBC application installation.
• coredumpProfile – The core dump settings for this server.
• role – If set to ‘primary’, role designates a server for internal processing.
• deviceSmartAttrib – The smart control attribute value that reports disk life remaining. A value of 0 means that no overriding attribute is available. The SBC could still be using an internal value based on pre-defined settings of known disk types. If the SBC is unable to retrieve a value (reports "n/a") for "Disk Life Remaining" when you run the hardDiskStatus command you may be able to specify the integer ID number of a smart control attribute that reports the percentage lifetime used for the disk. Contact Ribbon Technical Support for assistance in determining whether there is a valid smart control attribute available on your system.
• modularType – If set to 'true', the SBC uses modular DSPs.
• hwType – The type of server module the indexed slot has been configured to accept.
• pktPortSpeed – Packet port speed setting (1Gps, 10Gps).

• hwSubType – This field stores the SBC SWe subscription type.

  • virtual – SBC SWe configured for Virtual (non-Cloud) environment.
  • virtualCloud – SBC SWe configured for Cloud environment.

serverSoftwareUpgradeStatus

The system server software upgrade status table describes the status of the server software upgrade module.

• <server name>
• upgradeStatus – Indicates the current status of the server (none, pendingRevert, pendingUpgrade, reverted, reverting, revertingOnError, upgraded, upgrading)

serverStatus

The system server status table provides status of the server module.

• name – The node name.
• hwType – The type of server module the indexed slot has been configured to accept.
• serialNum – Serial number of the server module.
• partNum – Identifies the part number of the module.
• platformVersion – Platform version currently running on server.
• applicationVersion – Indicates the application version currently running on server.
• mgmtRedundancyRole – Redundancy role of the server (for management entities)
• upTime – Server module uptime in days/hours/minutes/seconds
• applicationUpTime – Indicates application uptime on the server in days/hours/minutes/sec.
• lastRestartReason – Reason for last restart of server.
• syncStatus – Inter-CE data synchronization state.
• daughterBoardPresent – Daughter board presence indicator.
• currentTime – Current system time.
• pktPortSpeed – Packet port speed setting (1Gps, 10Gps).
• actualCeName
  • Cloud platform: The ceName provided in the user data.
  • Non-Cloud platform: The SBC name entered during the SBC application installation.
    

• hwSubType – This field stores the SBC SWe subscription type.

  • virtual – SBC SWe configured for Virtual (non-Cloud) environment.
  • virtualCloud – SBC SWe configured for Cloud environment.
• fingerprint – The licensing fingerprint for the node.

<system name> detailedStatus – Prints the complete Live Software Upgrade (LSWU) upgrade details for the specified system to the screen. Details include the number of steps involved, the time taken to completed LSWU and upgrade process results.

softwareUpgradeStatus

LSWU status at any given time with the following details.

• activeCeAtStart – Active CE name when the upgrade started.
• cemodeAtStart – CE mode when upgrade started (single/dual).
• modelChange – Indicates if process model changed as part of this upgrade.
• newRelease – Software release to which the upgrade is performed.
• oldRelease – Software release running before upgrade started.
• package – Name of the new package.
• previousState – This is the previous LSWU state.
• primaryUpgradeStatus – Indicates the current status of the primary server.
• reason – Exit reason for failure of last software upgrade.
• revertScript – Revert script to run in case upgrade fails.
• revertStartTime – Start time of revert activity.
• rpmName – Name of the new rpm used for upgrade.
• secondaryUpgradeStatus – Indicates the current status of the secondary server.
• state – Current LSWU state.
• upgradeScript – Script to run to perform upgrade.
• upgradeStartTime – LSWU start time.

Sync status details of the standby node for active nodes created through a N:1 redundancy group configuration.

• Call/Registration Data – The sync state of Call/Registration data for active or standby node.
• Metavar Data – The sync state of metavariable data for the active or standby node.

syncStatus

HA Redundancy:

Sync status of both the active and standby nodes for an SBC HA pair.

• Call/Registration Data – Call/Registration data synchronization status with the SBC peer 

• Configuration Data – Configuration data synchronization status with the SBC peer
• Disk Mirroring – Disk Mirroring synchronization status with the SBC peer
• Policy Data – Policy data synchronization status with the SBC peer

N:1 Redundancy:

Sync status of both the active and standby nodes created through a N:1 redundancy group.

• Call/REgistration Data – The sync state of Call/Registration data for active or standby node.
• Metavar Data – The sync state of metavariable data for the active or standby node.

systemCongestionCurrentStatistics

The Sonus System Congestion Current Statistics table details.

• avgCallRate – The average call rate calculated using the formula: (# call attempts in an interval) / (# seconds elapsed in that interval).
• avgRegRate – The average registration rate calculated using the formula: (# registration attempts in an interval) / (# seconds elapsed in that interval).
• avgSubsRate – The average SIP SUBSCRIBE arrival rate calculated using the formula: (# SUBSCRIBE attempts in an interval) / (# seconds elapsed in that interval).
• callArrivals – The number of call arrivals since the current interval started.
• emergencyCallArrivals – The number of SIP emergency call arrivals since the current interval started.
• emergencyCallRejects – The number of SIP emergency call rejects since the current interval started.
• levelMC1Count – The number of transitions into MC1 since the current interval started.
• levelMC1TotalTime – The total number of seconds spent in MC1 since the current interval started.
• levelMC2Count – The number of transitions into MC2 since the current interval started.
• levelMC2TotalTime – The total number of seconds spent in MC2 since the current interval started.
• levelMC3Count – The number of transitions into MC3 since the current interval started.
• levelMC3TotalTime – The total number of seconds spent in MC3 since the current interval started.
• overloadRejects – The number of calls rejected due to system congestion since the current interval started.
• peakCallRate – The system peak call arrival rate (in calls per second) since the current interval started.
• peakRegRate – The peak SIP registration arrival rate (in registrations per second) since the current interval started.
• peakSubsRate – The peak SIP SUBSCRIBE arrival rate (in subscriptions per second) since the current interval started.
• sipRegArrivals – The number of SIP registrations arrivals since the current interval started.
• sipRegRejects – The  number of SIP registrations rejected since the current interval started.
• sipSubsArrivals – The number of SIP SUBSCRIBEs that arrived since the current interval started.
• sipsSubsRejects – The number of SIP SUBSCRIBEs that are rejected due to system congestion since the current interval started.

systemCongestionIntervalStatistics 

The Sonus System Congestion Interval Statistics details.

• <sequence number> – The interval sequence number. The number of intervals to store are configurable. Refer to Interval Statistics - CLI for configuration details.
• avgCallRate – The system average call arrival rate over the reporting inteval (callArrivals / interval-time = avgCallRate).
• avgRegRate – The average SIP registration arrival rate (in registrations per second) over the reporting interval.
• avgSubsRate – The average SIP SUBSCRIBE arrival rate (in subscriptions per second) over the reporting interval.
• callArrivals – The total count of call arrivals during the interval (callArrivals / interval-time = avgCallRate) .
• emergencyCallArrivals – The total count of SIP emergency calls that arrived.
• emergencyCallRejects – The total count of rejected SIP emergency calls.
• intervalValid – A setting of 'true' indicates the interval contains valid data during the time interval. Each interval is for a configurable fixed time (default interval is 15 minutes) starting on the hour. For example, if the system starts at 12:05, the first interval at 12:15 will not be valid because it is less than the 15-minute interval. Subsequent intervals will be valid upon meeting the 15-minute time interval. System switch-overs also cause invalid intervals because data is lost during the interval.
• levelMC1Count – The total count of transitions into MC1 during the interval.
• levelMC1TotalTime – The total time spent (in seconds) in MC1 during the interval.
• levelMC2Count – The total count of transitions into MC2 during the interval.
• levelMC2TotalTime – The total time spent (in seconds) in MC2 during the interval.
• levelMC3Count – The total count of transitions into MC3 during the interval.
• levelMC3TotalTime – The total time spent (in seconds) in MC3 during the interval.
• maxActiveCalls – The high water mark of the total number of active calls in both inbound and outbound directions on all trunk groups in the system for specified interval. This statistic applies to calls which are setting up, tearing down or stable.
  
  

  Switch-over scenario:

  When a switch-over occurs from SBC-A to SBC-B, the number of stable calls that were transferred from SBC-A to SBC-B equals the initial value of "maxActiveCalls" (immediately after the switch-over). Subsequent values are calculated and recorded accordingly.

• overloadRejects – The total count of calls rejected during the collection interval.
• peakCallRate – The system peak call arrival rate (in calls per second) measured during the collection interval.
• peakRegRate – The peak SIP registration arrival rate (in registrations per second) measured during the collection interval.

• peakSubsRate – The peak SIP SUBSCRIBE arrival rate (in subscriptions per second) measured during the collection interval.

• sipRegArrivals – The total count of SIP registrations that arrived during the collection interval.
• sipRegRejects – The total count of SIP registrations rejected during the collection interval.

• sipSubsArrivals – The total count of SIP SUBSCRIBEs that arrived during the collection interval.

• sipsSubsRejects – The number of SIP SUBSCRIBEs rejected during the collection interval.

• time – The system up time when the interval statisitic is collected.

systemCongestionStatus

System Congestion status status/statistics details.

• systemCongestionCPULevel – The current System Machine Congestion (MC) Level at the time this command is executed.

  • 0 – No Congestion

  • 1 – Level one congestion

  • 2 – Level two congestion

  • 3 – Level three congestion

• systemCongestionCallAcceptCount – A snapshot of the number of calls being accepted by the system. A value of "65535" represents all calls. During MC2 congestion, SBC calculates the CallAcceptRate peridocially (each second), and uses the value to compute a new CallAcceptCount.
• systemCongestionCallAcceptRate – Current rate (in calls per second) at which calls are being accepted by the system.
• systemCongestionCallArrivalRate – A snapshot of the number of call arrivals in the last second.
•  systemCongestionCallEqArrivalRate – Indicates the number of call/subscribes/registrations arrival per second. For registrations and subscriptions, the counter is incremented after every four new subscriptions/registrations. For calls, the counter is incremented after every new call.
• systemCongestionCallRateLevel – Call rate congestion level.
•  systemCongestionIRTTLevel – Internal RoundTrip Time (IRTT) congestion level.
• systemCongestionMCDuration – Number of seconds the system has been at this congestion level.
• systemCongestionMCLevel – System congestion level.
• systemCongestionRegArrivalRate –  A snapshot of the number of SIP registration arrivals in the last second.
• systemCongestionSubsArrivalRate – The number of SIP SUBSCRIBEs that arrived in the last second.

(Available only on SWe except ssbc SWe)

• cpu – Number of cores used by CPU-based transcoding. This is system level information and shows only one entry in case of HA system.
• gpu – GPU information. This is system level information and shows only one entry in case of HA system.
  
  • gpuName – Name of the GPU, this is used to differentiate between instances of same GPU type such as M60_0, M60_1.
  • cpuCoresUsed – CPU cores used for GPU transcoding by this GPU.
  • gpuType –  GPU type.
  • gpuAllocationRatio – GPU allocation ratio. Reserved for future use.
    

(Available only on SWe except ssbc SWe)

Shows type of transcode information used (CPU, GPU, CPU + GPU, HWDSP). This is system level information and shows only one entry in case of HA system.

System name

Announcement segment NP memory usage.

• cachedSegments – Number of announcement segments cached in NP memory.
• totalCacheMemory – Total amount of segment cache memory available in NP.
• totalPlayoutTime – Total playout time of all segments cached in NP memory.
• totalSegments – Total number of announcement segments on disk.
• usedCacheMemory – Amount of segment cache memory being used in NP.
• utilizedCacheMemory – Percentage of segment cache memory being used in NP.

segmentStatus <segment ID>

Announcement segment file status.

• audioFormat – Compression type of audio data.

• audioLength — Length of audio data in segment file.

• pathname – Pathname of segment file.

• playoutDuration – Playout duration of segment file.

• state – State of segment.

• totalPlays – Total number of times this segment has been played.

• useCount – Number of announcements currently using this segment.

• version – Version number of segment file.

Daughter board identifier

SBC 5000 series:

• SPS100 – SBC 5x00 SPS100 module
• DB0 – SBC 5x00 SPS100DB 0 module
• DB1 – SBC 5x00 SPS100DB 1 module
• DSP20 – SBC 5x10 DSP20 module
• DSP25 – SBC 5x10 DSP25 module

SBC 7000 series:

• FRU_DSP1 – SBC 7000 DSP-LC slot 1

• FRU_DSP2 – SBC 7000 DSP-LC slot 2

• FRU_DSP3 – SBC 7000 DSP-LC slot 3

• FRU_DSP4 – SBC 7000 DSP-LC slot 4

 A card’s programmed firmware version (using FPGA build date)

NOTE: This maintenance field does not apply to SPS100 cards.

Number of module boot failures since the last successful module boot, for use during diagnostic testing of a potentially failed module.

NOTE: This maintenance field does not apply to SPS100 cards.

Operational state of daughter board.

• disabled – Card is disabled.
• dryup – Card is enabled but in the process of drying up. Once completed, card will be set to ‘disabled’.
• enabled – Card is enabled.
• failed – If a DSP2x or DSP-LC module fails to boot over three consecutive tries (typically due to a hardware failure), it is taken out of service and marked as state “failed”. The rest of the system continues to boot normally, including any other DSP modules. The module failure is logged/alarmed with trap “sonusConnexIpSystemCESlotFailedNotification”. The slot remains in the failed state until the module is disabled and re-enabled once a replacement card is installed.
• loading – Card is enabled but in the process of booting. Resources are not yet available. Once completed, card will be set to ‘enabled’.
• locked – Slot capacity is locked out due to mismatch (with “preserveRedundancy” configured).

NOTE: For 5x00 systems, only the “enabled” state displays in the results.

serialNum

Identifies the serial number of the module (if present)

dspStatus dspUsage

<system name> – The SBC system name.

The below fields display raw count of DSP resources (i.e. channels) in use on each slot to aid in understanding which slots are loaded and to what extent in case card removal/hot swap is necessary.

• slot1ResourcesUtilized

• slot2ResourcesUtilized

• slot3ResourcesUtilized

• slot4ResourcesUtilized

For each DSP codec, a <codec>Total and <codec>Utilization field displays. 

1. 1. The <codec>Total field indicates how many transcoding sessions the system can support for that codec to G.711.
   2. The <codec>Utilization field indicates what percent of those sessions are actually in use.
      
      NOTE: For compressed-to-compressed transcoding, two resources are required, one for each codec. 

Additional fields:

• amrNbTotal – Total AMR–NB resource capacity on this server.

• amrNbUtilization – Percentage utilization of AMR–NB resources on this server.

• amrWbTotal – Total AMR–WB resource capacity on this server.

• amrWbUtilization – Percentage utilization of AMR–WB resources on this server.
• compressionAllocFailures – Running count of resource allocation failures due to resource exhaustion.
• compressionAvailable – Actual compression resources currently available in real time. This essentially equates to the total number of G.711 resources after loading.
• compressionTotal – Maximum number of compression resources on the server (i.e. before loading, so this number is static). This essentially equates to the total number of G.711 resources before loading (i.e. lightest codec).

• compressionUtilization – Percentage of compression resources in use (accounting for various codec weights). This can be calculated using the formula (compressionTotal – compressionAvailable) / compressionTotal.
  NOTE: Use this value when determining the extent of DSP module load (regardless of codec type).

• ecmTotal – Total T.38 ECM resource capacity on this server.
• ecmUtilization – Percentage utilization of T.38 ECM resources on this server.
• ecmV34Total – Total T.38 ECM V.34 resource capacity on this server.
• ecmV34Utilization – Percentage utilization of T.38 ECM V.34 resources on this server.
• efrTotal – Total EFR resource capacity on this server.
• efrUtilization – Percentage utilization of EFR resources on this server.
• evrc0Total – Total EVRC0 resource capacity on this server.
• evrc0Utilization – Percentage utilization of EVRC0 resources on this server.
• evrcb0Total – Total EVRCB0 resource capacity on this server.
• evrcb0Utilization – Percentage utilization of EVRCB0 resources on this server.
• evsTotal – Total EVS resource capacity on the present server.
• evsUtilization – Percentage utilization of EVS resources on the present server.
• g711SsTotal – Total G711SS (silence suppression) resource capacity on this server.

• g711SsUtilization – Percentage utilization of G711SS (silence suppression) resources on this server.

• g711Total – Total G711 resource capacity on this server.

• g711Utilization – Percentage utilization of G711 resources on this server.
  NOTE: The g711Utilization includes g711 channels in use plus channels that are reserved but not activated as part of the call set up process.  In this case, ensure to reserve enough resources to account for the worst case codec. For example, in release 4.2.x, a reserved channel is about 4.5 times as expensive as a G.711 channel. 

• g711V8Total – Total G711 V8 resource capacity on this server.

• g711V8Utilization – Percentage utilization of G711 V8 resources on this server.

• g722Total – Total G.722 resource capacity on this server.
• g722Utilization – Percentage utilization of G.722 resources on this server.

• g722V8Total – Total G.722 V8 resource capacity on this server.

• g722V8Utilization – Percentage utilization of G.722 V8 resources on this server.

• g726Total – Total G726 resource capacity on this server.
• g726Utilization –  Percentage utilization of G726 resources on this server.

• g726V8Total – Total G726 V8 resource capacity on this server.

• g726V8Utilization – Percentage utilization of G726 V8 resources on this server.

• g729AbTotal – Total G729A+B resource capacity on this server.
• g729AbUtilization – Percentage utilization of G729A+B resources on this server.

• g729AbV8Total – Total G729A+B V8 resource capacity on this server.

• g729AbV8Utilization – Percentage utilization of G729A+B V8 resources on this server.

• g7221Total – Total G.722.1 resource capacity on this server.
• g7221Utilization – Percentage utilization of G.722.1 resources on this server.

• g7221V8Total – Total G.722.1 V8 resource capacity on this server.

• g7221V8Utilization – Percentage utilization of G.722.1 V8 resources on this server.

• g7231Total – Total G723.1 resource capacity on this server.
• g7231Utilization – Percentage utilization of G7231 resources on this server.

• g7231V8Total – Total G723.1 V8 resource capacity on this server.

• g7231V8Utilization – Percentage utilization of G7231 V8 resources on this server.

• ilbcTotal – Total iLBC resource capacity on this server.
• ilbcUtilization – Percentage utilization of iLBC resources on this server.

• ilbcV8Total – Total iLBC V8 resource capacity on this server.

• ilbcV8Utilization – Percentage utilization of iLBC V8 resources on this server.

• opusTotal – Total OPUS resource capacity on this server.

• opusUtilization – Percentage utilization of OPUS resources on this server.

• silk16Total – Total Silk16 resource capacity on this server.
• silk16Utilization – Percentage utilization of Silk8 resources on this server.
• silk8Total – Total Silk8 resource capacity on this server.
• silk8Utilization – Percentage utilization of Silk8 resources on this server.
• toneAllocFailures – Percentage of tone resource allocation failures on this server.
• toneAvailable – Number of tone resources currently unused and available on this server.
• toneTotal – Total tone resource capacity on this server.
• toneUtilization – Percentage utilization of tone resources on this server.

licenseDomainBundleInfo

License details for the domain licenses available on the SBC.

• activeLicenseMode – The licensing mode currently in use by the SBC
• bundleName – License bundle name
• expirationDate – License expiration date
• featureName – license keys for each licensed feature
• generationDate – The date the license was generated
• installDate – The date the license was installed
• licenseId – License ID
• lineId – The line ID for the license feature entry
• purchaseOrderId – The purchase order ID specified when the license was generated
• usageLimit – Usage limit for the licensed feature

Status details for all licensed features or for a specified <featureName>.

• <featureName> – license keys for each licensed feature:

  • DSP-AMRNB

  • DSP-AMRWB

  • DSP-EVRC

  • DSP-EVS

  • DSP-G722

  • DSP-SILK

  • ENCRYPT

  • POL-BASE

  • SBC-1X10GMP

  • SBC-4X1GMP

  • SBC-CAPACITY

  • SBC-LI

  • SBC-MRF-RTU

  • SBC-NICEREC

  • SBC-P-DCS-LAES

  • SBC-POL-E911

  • SBC-POL-ENUM

  • SBC-POL-RTU

  • SBC-PSX-RTU

  • SBC-RTU

  • SBC-SIP-I

  • SBC-SIP323

  • SBC-SIPREC

  • SBC-VIDEO

  • SRTP

  • SWE-INSTANCE

  • VDSP-RTU

• currentLicenseAvailability – whether a license for the feature is available:
  • Available - feature is present in a legacy license bundle with a positive count or the most recent request to a network license server returned success.
  • NotRequired - feature is not present in the installed license.
  • Unavailable - the most recent request for a network license returned failure.
  • GracePeriod - the SLS is unreachable.
  • Expired - the legacy license expiration date has passed.
• currentLicensesInUse – the number of licenses currently in use
• currentLicensesTotal – the usage limit for the feature
• licenseInstalled – "Yes" means the feature is part of a legacy license bundle with a positive count, or the license is specified in the required license table for network licensing.
• licenseSought – The number of times the SBC requested a license for each feature from the Site License Server (SLS)
• licenseNotReceived – The number of times a license is not received from the SLS for each feature
• licensingStatus – whether the specified feature or call admission of the specified type is enabled or disabled:
  • Feature Enabled - license is available.
  • Feature Disabled - license is not available.
  • Call Admission Enabled - license is available or license availability is not required. Calls are accepted.
  • Call Admission Disabled - license is unavailable and call admission is not possible until license becomes available.
    

NOTE: Some fields only apply if the current licenseMode is "network".

licenseInfo

The license status for all license features or for a specified <featureName> <licenseID> combination.

• <featureName> – license keys for each licensed feature:

  • DSP-AMRNB

  • DSP-AMRWB

  • DSP-EVRC

  • DSP-EVS

  • DSP-G722

  • DSP-SILK

  • ENCRYPT

  • POL-BASE

  • SBC-1X10GMP

  • SBC-4X1GMP

  • SBC-CAPACITY

  • SBC-LI

  • SBC-MRF-RTU

  • SBC-NICEREC

  • SBC-P-DCS-LAES

  • SBC-POL-E911

  • SBC-POL-ENUM

  • SBC-POL-RTU

  • SBC-PSX-RTU

  • SBC-RTU

  • SBC-SIP-I

  • SBC-SIP323

  • SBC-SIPREC

  • SBC-VIDEO

  • SRTP

  • SWE-INSTANCE

  • VDSP-RTU

• <license ID> – License identifier
• expirationDate – The expiration date for a licensed feature
• inUse – The number of licenses used by the SBC for this feature
• licenseId – License identifier
• source – Source of the license (BuiltIn, Legacy, or Network)
• usageLimit – The maximum count allowed for this feature

License details for the legacy licenses stored on the SBC.

• bundleName – License bundle name
• featureName – license keys for each licensed feature
• licenseId – License ID
• expirationDate – License expiration date
• usageLimit – Usage limit for the license
• activeLicenseMode – The licensing mode currently in use by the SBC (legacy/network/domain)

Displays the licenseRequired configuration: The configured minimum and maximum number of licenses for a particular feature to request from the Site License Server (SLS) for the SBC application to use.

• featureName – license keys for each licensed feature
• minCount – The minimum number of licenses the SBC will request from the SLS to retain at the SBC (regardless of demand) when the associated license is first configured.
• maxCount – The maximum number of licenses the SBC can request from the SLS.

(Applies to 'show table' command only)

NOTE: This field only applies if the current licenseMode is "network" or "domain."

NOTE: minCount and maxCount are not configurable for services controlled by instance licenses. These services are enabled system-wide when a single token of the feature license is present at the system.

Status information about licenses acquired by the SBC application.

• name – SLS server name.
• featureName – license keys for each licensed feature.
• lastAcquiredCount – The last count of the number of licenses requested from the SLS. 
• lastGoodServerName – The last SLS server that provided this license.
• lastAcquiredDate – The last time the license was successful refreshed on the server.
• usingCapacityLicense – If set to "Y", capacity licenses are used and the session count is unlimited and only one license is requested from the SLS. If set to "N", then the number of licenses listed in lastAcquiredCount were requested from the SLS.
• serviceAuthorizationMode – If set to "Y", once the license is first acquired from the SLS the service is enabled and the license considered persistent at the SBC without any further interaction required with the SLS.

Per-server license configuration.

• serverName – The name of the Site License Server (SLS)
• priority – The SLS server selection priority
• serverAddress – The SLS FQDN or IP address

(Applies to 'show table' command only)

NOTE: This field only applies if the current licenseMode is "network".

License server status details.

• serverName – The name of the SLS
• isCurrentActive – A result of "y" indicates this server is the last server to respond correctly to a request
• requestMessagesSent – The number of license requests sent to this SLS
• licenseGrantMessagesReceived – The number of license grant messages received from the SLS
• licensePartialGrantMessagesReceived – The number of partial license grant messages received from the SLS
• licenseRejectMessagesReceived – Indicates the number of license reject messages received from the SLS
• licenseErrors – The number of errors that occurred while sending a request to this SLS (includes no-response received type errors)

NOTE: This field only applies if the current licenseMode is "network".

licenseStatus

The CE license status table describes the current CE license state, for example "dualCe".

•   cemode

Specifies the leader statistics table.

• <key>
• leaderElectionAttempts
• retransmitCount
• requestTimeoutCount

Displays the IP address of leader nodes in the cluster.

• <leader Id>
• leaderIPAddress
• state

Specifies the load balancing service mode for REGISTERs (disable, redirect). If set to redirect, new registrations are retargeted, as necessary, to balance the load using SIP 302 "Moved Temporarily" response code.

Node resource information.

• <Id>
• callResourceCount
• registrationResourceCount

Displays the instance status of the leader nodes in the cluster.

• <leader Id>
• leaderIPAddress
• state

Displays media resource cache information.

• <node index> – Node ID
• nodeIpAddress – Node's IP address
• nodePrivateLifGroupName – Node's private LIF group name
• nodePrivateLifGroupBandwidth – Available private LIF group bandwidth for this node, in bytes/second
• nodePrivateLifGroupTtl – The LIF group Time To Live (TTL) value (Number of seconds remaining for the current resource bandwidth information to be valid) for this node
• nodeCodecUnits – Number of available codec units (at any instant) the SSBC can use to allocate the transcoding resources for an active call
• nodeCodecCapabilities – Displays the supported codec and corresponding codec units for this node
• nodeCodecCapabilitiesExtn – Displays additional supported codec and corresponding codec units than what is listed under nodeCodecCapabilities
  
• nodeCodecTtl – The codec TTL value (Number of seconds the present codec is available) for this node
• nodeToneUnits – The percentage of DSP cores available for the present tone
• nodeToneTtl – Number of seconds the present tone is available

Displays cluster seed node status.

• <Seed ID>
• seedNodeIpAddress

Specifies the load balancing service mode for INVITEs. Enables load balancing for initial INVITE requests. 

If set to redirect, calls may get retargeted using SIP 302 to balance the load.

• disabled
• redirect

Specifies the leader statistics table.

• <key>
• leaderElectionAttempts
• retransmitCount
• requestTimeoutCount

Displays the IP address of leader nodes in the cluster.

• <leader Id>
• leaderIPAddress
• state

Displays policer cluster leader node status.

• <leader Id>
• leaderIPAddress

Displays policer media resource cache information.

• <node index>
• nodeIpAddress
• nodeLifGroupName
• nodeLifGroupisPrivate
• nodeLifGroupBandwidth
• nodeLifGroupTtl

Displays policer cluster seed node status.

• <leader Id>
• seedNodeIPAddress

Specifies the load balancing service mode for REGISTERs (disable, redirect). If set to redirect, new registrations are retargeted, as necessary, to balance the load using SIP 302 "Moved Temporarily" response code.

Node resource information.

• <leader Id>
• callResourceCount
• registrationResourceCount 

Displays media resource cache information.

• <node index>
• nodeIpAddress
• nodePrivateLifGroupName
• nodePrivateLifGroupBandwidth
• nodePrivateLifGroupTtl
• nodeCodecUnits
• nodeCodecCapabilities 
• nodeCodecCapabilitiesExtn 
  
• nodeCodecTtl
• nodeToneUnits
• nodeToneTtl

Specifies the leader statistics table.

• <key>
• leaderElectionAttempts
• retransmitCount
• requestTimeoutCount

Displays the IP address of leader nodes in the cluster.

• <leader Id>
• leaderIPAddress
• state

Displays policer media resource cache information.

• <node index>
• nodeIpAddress
• nodeLifGroupName
• nodeLifGroupisPrivate
• nodeLifGroupBandwidth
• nodeLifGroupTtl

annStatistics

Announcement statistics:

• npId – Network processor ID
• numEnable – Current number of announcements enabled
• numPlaying – Current number of announcements playing
• pktsToDsp – Total number of packets sent to DSP
• pktsToEth – Total number of packets sent to Ethernet port
• stop – If set, all current announcements will gradually stop
• numAnnIndToHost – Number of indications sent
• numSlip – Number of announcements with interval slip
• outQcongest – Total number of errors
• timerAddErr – Number of timer schedule errors
• LastErrAid – Last Announcement ID for timerAddErr
• indWorkNull – No work entry counter for announcement indication
• indBufNull – Buffer null counter for announcement indication
• annWorkNull – No work entry counter for announcement
• annBufNull – Buffer null counter for announcement

Packet defragmentation statistics:

• npId – Network processor ID
• reassembleRequired – Total fragment context created for packets requiring reassembly
• goodFragments – Number of good fragments processed
• reassembleComplete – Good complete datagram
• inUse – Current number of defrag contexts used
• errorPkt – Bad fragment packet, duplicate, too many fragments, bad offset, packet too big
• timeoutCnt – Number of timeouts that have occurred
• badInputBuffer – Bad input buffer
• badDefragPool – Invalid buffer pool count
• badTimeoutList – Invalid age list for timeout maintenance
• tooManyFrags – Number of contexts exceeding maximum fragments allowed
• noDefragMatch – Number of fragments failed to find frag context, out of fragment context

Digit insertion statistics

• npId – Network processor ID
• startCnt – Total start count
• stopCnt – Total stop count
• modifyCnt – Total modify count
• earlyStartCnt – Total early start (start before end) count
• cancelRescheduleCnt – Total cancel and reschedule count
• badStopCnt – Total bad stop count
• mediaNotEnabledCnt – Total digit commands issued for disabled media flow
• uknownStateCnt – total unknown state count
• timerCancelFailCnt – Total failure count of cancelling timer bucket
• timerAddFailCnt – Total failure count of adding timer bucket
• failedGetWork – Unable to get work entry to send digit
• failedGetPktBuf – Unable to get packet buffer to send digit

RTCP Generation statistics.

• npId – Network processor ID
• startCnt – Total start count
• stopCnt – Total stop count
• modifyCnt – Total modify count
• haltCnt – Total number of halt commands
• restartCnt – Total number of restart commands
• cancelCnt – Total cancel and no–schedule count
• totalScheduled – Total RTCP packets scheduled
• lastScheduled – Last RTCP packet timer scheduled
• earlyStartCnt – Total early start (start before end) count
• badStopCnt – Total bad stop count
• badModifyCnt – Total RTCP modify but RTCP is not enabled count
• badGenType – Unsupported gen type passed in command
• doubleEnableCnt – Enable command for an already enabled RTCP
• timerCancelFailCnt – Total failure count of cancelling timer bucket
• timerAddFailCnt – Total failure count of adding timer bucket.
• failedGetWork – Unable to get work entry to send RTCP
• failedGetPktBuf – Unable to get packet buffer to send RTCP

• numWorkAtDiscard – RTCP not generated because state at discard

• numWorkAtDisabled – RTCP not generated because state at disabled
• numWorkAtHalt – RTCP not generated because state at halt
• lastBadRtcpGen – Last RTCP that was not generated

Displays NTP server key details.

• keyId
• keyType
• keyValue

Displays status information about each NTP peer.

• ceName – The name of this SBC server.
• ipAddress – IP address of the CE.

• state – the state of the NTP peer (insynce, outofsync, reachable).
• stratum – A number representing the distance from the reference clock, starting at "0". Stratum 16 represents that a device is out of sync.
• refTime – The time this NTP peer was last updated.

Displays information about each NTP Server configured to provide network time.

• ipAddress – The IP address of this NTP server.
• version – The NTP version of this NTP server.
• minPoll – The minimum poll interval to this NTP server.
• maxPoll – The maxiimum poll interval to this NTP server.
• state – The configured state of the NTP server entry.

Displays system status information about NTP.

• ceName – The name of this SBC server.
• clock – The SBC regularly checks system time. This field represents the system time as of the last check by SBC, not the actual system time.
• refTime – The time this system was last updated.

timeZone

This table contains Time Zone configuration. Fields include:

• name – System name.
• zone – The current time zone.

NOTE: In an HA configuration, the Active and Standby system times and refTimes will not match in the results of this command because SBC updates NTP data independently.

Defines global configuration applicable to all policy servers.

• congestionControl – The SBC throttles the sending or policy requests to either active or standby PSX when this field is enabled.
• mgmtInterfaceGroup – The Management Interface Group to use for communicating with external PSX.
• reconnectTimeout – The timer parameter for re-attempting connection to a Policy Server that is in the enabled state in seconds.
• switchOverMode – (automatic or manual) This setting determines how the policy server is set to ACTIVE after a switchover.
• type – Interface type supported by policyServer.

Local (embedded) policy server configuration.

• action – The action for the operation mode for this trunk group
• keepAliveTimer – The time in seconds between sending Keep Alive indications to the internal Policy Server.
• mode – Assignment of the Policy Server to have the active, standby, out of service or alternate role.
• retries – The maximum number of retransmission attempts for a transaction on this Policy Server.
• retryTimer – The time in milliseconds that the SBC waits for a response from the local Policy Server.
• state – Administrative state of the softswitch server.
• transactionTimer – The time in milliseconds that the SBC waits for a response from the Policy Server after sending it a transaction request.

Policy Server status table. Fields include:

• allowancePercent – The number of SBC policy requests allowed by PSX. For example, an allowance of 75%, means that the SBC is skipping one out of every four policy requests. This allowance is provisioned on the PSX and enforced on the SBC when PSX Congestion Control is enabled.

• averageTransactionTime – Records the average time taken in milliseconds for a softswitch transaction.

• congestionLevel – The PSX congestion level.

• dataRequests – The cumulative number of data requests received from the softswitch.

• index – Identifies the softswitch entry.

• interfaceIpAddress – Identifies the IP address the SBC uses to communicate with the PSX for this Policy Server.

• ipAddress – IP Address of the softswitch server.

• negotiatedVersion – The lowest negotiated protocol version between the gateway and all the active and alternate softswitches.

• operState – Operational state of the softswitch.

• queriesSkippedAndRejected – The cumulative number of rejected Policy Requests while the active PSX is congested and a standby PSX is either congested or not available.

• queriesSkippedAndServiced – The cumulative number of Policy Requests serviced by the standby PSX while the active PSX experienced congestion.

• redirectRequests – The cumulative number of redirect requests received from the softswitch.

• releaseRequests – The cumulative number of release-call requests received from the softswitch.

• serverReconnects – The number of successful reconnections between the gateway and the softswitch.

• transactionCompleted – The number of successful transactions between the gateway and the softswitch.

• transactionFailedAttempts – The number of unsuccessful transactions between the gateway and the softswitch.

• transactionRetryAttempts – The number of transaction retries between the gateway and the softswitch.

• version – The negotiated protocol version between the gateway and the softswitch.

remoteServer

Table of softswitch remote server configurations. Fields include:

• name – Remote server name.
• ipAddress – IP adddress of the remote server.
• portNumber – The IP port number of the softswitch server.
• state – Administrative state of the softswitch server.
• mode – Policy Server mode (active, standby, out of service or alternate role).
• action – The method by which queued transactions are processed when oper-state goes to standby or out-of-service. Possibilities include:
• dryup – all queue entries are processed to completion unless retries expires.
• force – all queue transactions are dropped immediately.
• transactionTimer – The time in milliseconds that the SBC waits for a response from the Policy Server after sending it a transaction request.
• keepAliveTimer – The time in seconds between sending Keep Alive indications to the Policy Server.
• retryTimer – The time in milliseconds that the SBC waits for a response from the Policy Server after retransmitting the transaction request.
• retries – The maximum number of retransmission attempts for a transaction on this Policy Server.
• subPortNumber – The port number assigned for the IP address of the Policy Server for the specific purpose of communicating subscriber data.

Checks for expired certificates, trust anchor validity, and if certificates have been revoked if OSCP is enabled. Fields include:

• certReCheckRate – The rate, in hours, to recheck certificates for TLS sessions.
• expirationPeriodicWarning – Interval of the periodic warnings in days generated after the certificate has reached the expiry threshold.
• expiryWarningThreshold – The number of days before generating a warning for a certificate nearing expiry.

IPsec configuration.

• ikeDpdInterval – The Dead Peer Detection interval.
• ikeRetransmitInterval – The IKE retransmit interval period in seconds.
• ikeRetrasmitCount – The number of IKE retransmits.

 This table contains OCSP profile usage status. Fields include:

• ocspName
• tlsName
• ocspTlsRefNum

This table contains OCSP Statistics. Fields include:

• ocspInternalErrors – Number of internal error responses.
• ocspMalformedRequests – Number of malformed request responses.
• ocspRepondersUnreachable – Number of times OCSP responders are unreachable.
• ocspRequestAttempts – Number of OCSP request attempts that have been made.
• ocspResponseTimeouts – Number of times OCSP response timeouts are encountered.
• ocspResponsesGood – Number of OCSP Responses received with 'Good' status.
• ocspResponsesRevoked – Number of OCSP Responses received with 'Revoked' status.
• ocspResponsesUnknown – Number of OCSP Responses received with 'Unknown' status.
• ocspSigRequired – Number of 'sigRequired' responses.
• ocspTryLaters – Number of 'tryLater' responses.
• ocspUnauthorized – Number of unauthorized responses.

• certStatistics– Certificate statistics.
  • caCerts – Number of installed CA/remote certificates.
  • localCerts – Number of installed local certificates.
• certificate – Collection of certificates configured on the SBC.

  • encoding – The encoding type of the certificate.

  • fileName – The certificate content file name

  • passPhrase – Pass-phrase to decrypt RSA private key in PKCS12 file.

  • state – The administration state of this certificate.

  • status – The status of the certificate.

  • type – The type of the certificate:

    • remote – certificate is imported from remote location.

    • local – certificate is used locally.

    • local-internal – local certificate with private key generated on the SBC.