Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a0c86e9b2550016ec54396b5000a, userName='null'}
JIRAIDAUTHSBX-124650
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a0c85652e498015697f3e3b3000b, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a0c85652e498015697f3e3b3000b, userName='null'}


Panel

In this section:

Table of Contents
maxLevel3


Include Page
SBXDOC120:_SBC 5100 5200 UnsupportedSBXDOC120:
_SBC 5100 5200 Unsupported

Use the SIP trunk group CAC parameters to configure call admission control (CAC) settings for a SIP trunk group on ingress, on egress, and as a whole.

Info
titleNote

As a best practice, always use UPPERCASE for trunk group names.


Include Page
SBXDOC120:_Param_values_exceptionSBXDOC120:
_Param_values_exception

Include Page
SBXDOC120:_Subscribe_CAC_Access_RestrictionSBXDOC120:
_Subscribe_CAC_Access_Restriction

SIP Trunk Group CAC

Command Syntax

Code Block
languagenone
% set addressContext <name> zone <name> sipTrunkGroup <name> cac
	bandwidthLimit <0-2147483647>
	bandwidthLimitThreshold <0-100>
    bandwidthVideoThreshold <0-100>
	callLimit <0-2147483647>
	callLimitThreshold <0-100>
	egress 
	emergencyOversubscription <0-1000>
	estimatedChildRegistrations <1-256>
	extendedEmergencyIpLimit <0-40000>
	hpcOversubscription <0-100>
	ingress 
	registeredEndpointCacProfile <profile name>
	registrationLimit <0-2147483647>
	subscriptionLimit <0-2147483647>
	tcpMediaLimit <0-5000>
	unRegisteredEndpointCacProfile <profile name>

Command Parameters

Caption0Table1

SIP Trunk Group CAC Parameters

ParameterLength/RangeDescription
bandwidthLimitunlimited or 0-2147483647
, or unlimited
The total media bandwidth limit, in Kbits/sec. (default = "unlimited")
bandwidthLimitThreshold0-100Enter threshold value (as a percentage) to specify bandwidth utilization notification threshold. (range: 0-100 / default = 0)
bandwidthVideoThreshold0-100Enter threshold value (as a percentage of video bandwidth) to limit video streams to a specific bandwidth to prevent video calls consuming call bandwidth otherwise needed for audio calls. (range: 0-100 / default = 0)
callLimitunlimited or 0-2147483647
, or unlimited
Total number of concurrent calls (either ingress or egress) allowed. (default = “unlimited”).
callLimitThreshold0-100Call Limit utilization notification threshold, as a percentage. (default = 0)
egressN/AEgress-specific call admission control configuration for the SIP trunk group. See the 
SIP Trunk Group - CAC - CLI#Egress
Egress Parameters table below for details.
emergencyOversubscription0-1000

The percentage of resource oversubscription allowed for emergency calls. (default = 10)

estimatedChildRegistrations1-256Estimated number of child registrations (i.e. the estimated number of P-Associated-URIs in 200 OK message). (default = 1)
extendedEmergencyIpLimit0-40000

The resource oversubscription (expressed as numeric value) allowed for emergency calls. (default = 0)

hpcOversubscription0-100This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10)
ingressN/AIngress-specific call admission control configuration for the SIP trunk group. See the 
SIP Trunk Group - CAC - CLI#Ingress
Ingress Parameters table below for details.
registeredEndpointCacProfileN/A<SIP CAC Profile Name> – The name of the SIP CAC Profile (containing endpoint CAC parameters that are applied individually to each registered peer) to associate with this trunk group.
registrationLimitunlimited or 0-2147483647
, or unlimited
The total number of concurrent SIP registrations allowed. (default is 'unlimited')
subscriptionLimitunlimited or 0-2147483647
, or unlimited
The total number of concurrent SIP subscriptions allowed on IP trunk group. (default is 'unlimited')
tcpMediaLimitunlimited or 0-5000
, or unlimited
MRM session limit per trunk group.

unRegisteredEndpointCacProfile

N/A

<SIP CAC Profile name> – The name of the SIP CAC profile (containing endpoint CAC parameters that are applied individually to each unregistered peer) to associate with this trunk group.

(Refer to SIP CAC Profile - CLI for profile details.)


Egress

Command Syntax

Code Block
languagenone
% set addressContext <name> zone <name> sipTrunkGroup <name> cac egress 
	callBurstMax <1-900> ( <"unlimited" or for SBC 5400/SWe: 1-900; SBC 7000 range is/SBC CNe: 1-2700)2700>
	callLimit <0-2147483647>
	callRateMax <1-450> ( <"unlimited" or for SBC 5400/SWe: 1-450; SBC 7000 range is/SBC CNe: 1-1350)1350>
	emergencyOversubscription <0-1000>
	extendedEmergencyIpLimit <0-40000>
	hpcOversubscription <0-100>
	otherReqBurstMax <1-1000> (<"unlimited" or for SBC 5400/SWe: 1-1000; SBC 7000 range is: 1-3000)3000>
	otherReqRateMax <1-1000> ( <"unlimited" or for SBC 5400/SWe: 1-1000; SBC 7000 range is 1-3000)3000>
	registerBurstMax <1-3000<"unlimited" or unlimited> (1-1500 or unlimited for SBC 5400;/SWe: 1-3000 or unlimited for 1500; SBC 7000): 1-3000>
    registerRateMax <1-3000<"unlimited or unlimited> ( for SBC 5400/SWe: 1-1500 or unlimited for; SBC 5400;7000: 1-30003000>
	subscribeBurstMax <"unlimited" or unlimited for SBC 7000)
	subscribeBurstMax <1-1000> (5400/SWe: 1-1000; SBC 7000 range is: 1-3000)3000>
	subscribeRateMax <1-1000> ( <"unlimited" or for SBC 5400/SWe: 1-1000; SBC 7000: range is 1-3000)3000>

Egress Command Parameters

Table
Info

Call policing using callRateMax and callBurstMax is applicable only to normal and emergency calls, not to high priority calls (HPC).

Caption
0

1Egress Parameters
3Egress Parameters


ParameterLength/RangeDescription
callBurstMax

unlimited or

SBC 5400/SWe: 1-900

SBC 7000/CNe: 1-2700

, or unlimited

Maximum allowed burst size (above the allowed sustained rate) for egress call attempts, in calls per second. (default = 'unlimited')
callLimitunlimited or 0-2147483647
, or unlimited
Total number of concurrent calls (either ingress or egress) allowed on egress. (default = 'unlimited')
callRateMax

unlimited or

SBC 5400/SWe: 1-450

SBC 7000/CNe: 1-1350

, or unlimited).

Maximum sustained egress call rate allowed in calls per second. (default = 'unlimited')

NOTE: You can set both callBurstMax and callRateMax as 'unlimited'; however, if you assign a value to one parameter, the other must also be assigned a value.

emergencyOversubscription  0-1000Over-subscription of resources (as a percentage) allowed for emergency calls. (default = 10)
extendedEmergencyIpLimit0-40000

The resource oversubscription (expressed as numeric value) allowed for emergency calls. (default = 0)

hpcOversubscription0-100This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are stopped, but additional HPC calls are allowed up to the configured percentage value. (default = 10)
otherReqBurstMax

unlimited or

SBC 5400/SWe: 1-1000

SBC 7000: 1-3000

, or unlimited

Maximum allowed burst (above the allowed sustained rate) for any other egress out-of-dialog SIP request. (default = 'unlimited')
otherReqRateMax

unlimited or

SBC 5400/SWe: 1-1000

SBC 7000: 1-3000

, or unlimited

Maximum sustained egress rate (requests per second) of other out-of-dialog SIP requests. (default = 'unlimited')

registerBurstMax

unlimited or

SBC 5400/SWe:

1-1500

or unlimited

SBC 7000:


1-3000

or unlimited

Specifies the maximum allowed egress burst (above the allowed sustained rate) for initial SIP registrations. The default value is unlimited.
registerRateMax

unlimited or

SBC 5400/SWe:

1-1500

or unlimited

SBC 7000:


1-3000

or unlimited

Specifies the maximum allowed sustained egress rate (registrations per second) for initial SIP registrations. The default value is unlimited.

NOTE: You can set both registerBurstMax and registerRateMax as 'unlimited'; however, if you assign a value to one parameter, the other must also be assigned a value.

 subscribeBurstMax

unlimited or

SBC 5400/SWe: 1-1000

SBC 7000: 1-3000

, or unlimited

Maximum allowed burst (above the allowed sustained rate) for egress initial SIP subscribe request. (default = 'unlimited')
subscribeRateMax

unlimited or

SBC 5400/SWe: 1-1000

SBC 7000: 1-3000

, or unlimited

Maximum sustained egress rate (subscribes per second) of initial SIP subscribe request. (default = 'unlimited')


Ingress

Command Syntax

Code Block
languagenone
% set addressContext <name> zone <name> sipTrunkGroup <name> cac ingress 
	callBurstMax <1-900> ( <"unlimited" or for SBC 5400/SWe: 1-900; SBC 7000 range is/SBC CNe: 1-2700)2700>
	callLimit <0-2147483647>
	callRateMax <1-450> (<"unlimited" or for SBC 5400/SWe: 1-450; SBC 7000/SBC rangeCNe: is 1-1350)1350>
	emergencyOversubscription <0-1000>
	hpcOversubscriptionextendedEmergencyIpLimit <0-100>40000>
	extendedEmergencyIpLimithpcOversubscription <0-40000>100>
	otherReqBurstMax <1-1000> (<"unlimited" or for SBC 5400/SWe: 1-1000; SBC 7000 range is: 1-3000)3000>
	otherReqRateMax <1-1000> (<"unlimited" or for SBC 5400/SWe: 1-1000; SBC 7000 range is 1-3000)3000>
	registerBurstMax <1-3000<"unlimited" or unlimited> (1-1500 or unlimited for SBC 5400;/SWe: 1-3000 or unlimited for 1500; SBC 7000): 1-3000>
    registerRateMax <1-3000<"unlimited or unlimited> ( for SBC 5400/SWe: 1-1500 or unlimited for ; SBC 5400;7000: 1-30003000>
	subscribeBurstMax <"unlimited" or unlimited for SBC 7000)
	subscribeBurstMax <1-1000> (5400/SWe: 1-1000; SBC 7000 range is: 1-3000)3000>
	subscribeRateMax <1-1000> ( <"unlimited" or for SBC 5400/SWe: 1-1000; SBC 7000: range is 1-3000)3000>

Ingress Command Parameters

Info

Call policing using callRateMax and callBurstMax is applicable only to normal and emergency calls, not to high priority calls (HPC).

Caption
0Table
1Ingress Parameters
3Ingress Parameters


ParameterLength/RangeDescription
callBurstMax

unlimited or

SBC 5400/SWe: 1-900

SBC 7000/CNe: 1-2700

, or unlimited

Maximum allowed burst (above the allowed sustained rate) for ingress calls in calls per second. (default = 'unlimited')
callLimit

unlimited or 0-2147483647

, or unlimited

Total number of concurrent calls allowed on ingress. (default = 'unlimited')

callRateMax 

unlimited or

SBC 5400/SWe: 1-450

SBC 7000/CNe: 1-1350

, or unlimited

Maximum sustained ingress call rate allowed in calls/second. (default = 'unlimited')

NOTE: You can set both callBurstMax and CallRateMax as 'unlimited'; however, if you assign a value to one parameter, the other must also be assigned a value.

emergencyOversubscription0-1000The amount of resource over-subscription (as a percentage) allowed for emergency calls. (default = 10)
extendedEmergencyIpLimit0-40000

The resource oversubscription (expressed as numeric value) allowed for emergency calls. (default = 0)

hpcOversubscription0-100This parameter specifies the amount of resource over-subscription (as a percentage) allowed for HPC calls. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured percentage value. (default = 10)
otherReqBurstMax 

unlimited or

SBC 5400/SWe: 1-1000

SBC 7000: 1-3000

, or unlimited

Maximum allowed burst (above the allowed sustained rate) for any other ingress out-of-dialog SIP request. (default = 'unlimited')

otherReqRateMax

unlimited or

SBC 5400/SWe: 1-1000

SBC 7000: 1-3000

, or unlimited

Maximum sustained ingress rate (requests per second) of other out-of-dialog SIP requests. (default = 'unlimited')

registerBurstMax

unlimited or

SBC 5400/SWe:

1-1500

or unlimited

SBC 7000:


1-3000

or unlimited

Specifies the maximum allowed ingress burst (above the allowed sustained rate) for initial SIP registrations. The default value is unlimited. 

registerRateMax

unlimited or

SBC 5400/SWe:

1-1500

or unlimited

SBC 7000:


1-3000

or unlimited

Specifies the maximum allowed sustained ingress rate (registrations per second) for initial SIP registrations. The default value is unlimited.

NOTE: You can set both “registerBurstMax” and “registerRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value.

subscribeBurstMax

unlimited or

SBC 5400/SWe: 1-1000

SBC 7000: 1-3000

, or unlimited

Maximum allowed burst (above the allowed sustained rate) for ingress initial SIP subscribe request. (default = 'unlimited')

subscribeRateMax

unlimited or

SBC 5400/SWe: 1-1000

SBC 7000: 1-3000

, or unlimited

Maximum sustained ingress rate (subscribes per second) of initial SIP subscribe request. (default = 'unlimited')

pagebreak