Page History

Add_workflow_for_techpubs

AUTH1 UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} JIRAIDAUTH CHOR-6845 REV5 UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} REV6 UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} REV3 UserResourceIdentifier{userKey=8a00a0c86a61778d016a7d0876df0017, userName='null'} REV4 UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca2f03d1, userName='null'} REV1 UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ce600bb3, userName='null'} REV2 UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c99e02c0, userName='null'}

Overview

The

Spacevars
0 series3

 can be deployed running as a VNF on a uCPE platform running an Intel Atom processor with 2.5 GHz or more.  All of the features and functionalities of the 

Spacevars
0 series3

are supported in this deployment type for 1, 2, or 4 vCPUs. Th

Spacevars
0 series3

can be deployed on Service Providers uCPEs, such as Versa. 

Hardware and Software Requirements

The following are the server and 

Spacevars
0 series3

requirements for running the 

Spacevars
0 series3

on a uCPE platform.

Server Hardware Requirements

Caption
0 Figure 1 Hardware and Software Requirements
Configuration Requirement Processor Intel Atom  CPU 2.5 GHz or more RAM Each  Spacevars 0 series3 instance requires 1, 2, or 4 GiB of RAM depending on the configuration Datastore Hard disk requirements are dependent upon the number of VNFs hosted, the size of each VNF at full size, and whether snapshots will be enabled

Spacevars
0 series3

 Requirements

General Recommendations

• Plan enough resources (RAM, CPU, NIC ports, hard disk, etc.) for all the VNFs to run on the server platform, including resources needed by the uCPE itself.
• Allocate each VNF with only as much virtual hardware as that VNF requires. Provisioning a VNF with more resources than it requires can, in some cases, reduce the performance of that VNF as well as other virtual machines sharing the same host.

• Disconnect or disable any physical hardware devices that you will not be using (floppy drives, network interfaces, storage controllers, optical drives, USB controllers, etc.) under BIOS settings to free up interrupt/CPU resources.

Caption
0 Figure 1 SBC SWe Edge Requirements
Setting Minimum vCPU 1, 2, and 4 supported. RAM 1 GB to support 1 vCPU 2 GB to support 2 vCPU 4 GiB to support 4 vCPU vNIC 3 Management Port, LAN Port, WAN Port. Note: One vNIC is mandatory for management.  Virtual Hard Disk  5 GiB

Install 

Spacevars
0 series3

as a VNF on a uCPE

Refer to the specific uCPE's documentation for installation instructions; the uCPE's vendor specific guidelines must be followed for 

Spacevars
0 series3

VNF deployments. 

Info
Before installation, ensure you downloaded the Spacevars 0 series3 . Refer to: Downloading the SBC SWe Edge Package for On-Premises Deployment.

Complete Initial Setup

For initial setup of the

Spacevars
0 series3

, refer to Running Initial Setup on SBC SWe Edge.

License Installation

If you are installing an 

Spacevars
0 series3

instance to carry live enterprise traffic, proceed to Obtaining and Installing an SBC SWe Edge Production Node-Locked License.