Versions Compared

Old Version 6

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
JIRAIDAUTHSYM-23168
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ce320b29, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ce340b42, userName='null'}

Include Page
Not_for_SWe
Not_for_SWe

...

There is a subtle but very important difference in the UI between ISDN/BRI (Basic Rate Interface) Signaling Groups and ISDN/PRI (Primary Rate Interface) Signaling Groups. These differences appear in the Port and Protocol panels.

Caption
0Figure
1Port and Protocol

Image RemovedImage Added

Configuration Field

PRI (T1)

BRI

Fractional

(tick)

(error)

TEI Assignment

(error)

(tick)

TEI

(error)

(tick)

...

  1. From the Create Signaling Group drop down box at the top of the Signaling Group Table, select ISDN Signaling Group.

    Panel
    borderStylenone

    Caption
    0Figure
    1Create ISDN Signaling Group

    Image Modified

     

    Anchor
    properties
    properties

...

Panel
bgColor#FAFAFA
borderStylenone

Specifies when to generate local ring back

  • Auto on Alert: Depends if inband audio is available when processing alert
  • Auto on Alert/Progress: Depends if inband audio is available when processing Alert or Progress
  • Always on Alert: Always generate inband ringback when processing Alert
  • Always on Alert/Progress: Always generate inband ringback when processing Alert or Progress
  • Never: Never generate inband ringback when processing Alert or Progress

Service Msg Capability

Panel
bgColor#FAFAFA
borderStylenone

Specifies if service messaging is used on the signaling group. Only valid for ATT 4ESS, ATT 5ESS, NI2 and INS Sonus 1500 Switch Variants.

...

Panel
bgColor#FAFAFA
borderStylenone

Specifies whether or not the Q.931 SETUP message is sent to the far-end should include the DISPLAY Information Element (IE).
Available only when ISDN Side is set to User and the Switch Variant is set to NI2 or Euro-ISDN.

If this option is enabled, the DISPLAY IE is populated for NI2 or Euro-ISDN switch types, otherwise the DISPLAY IE is not populated for these switch types.

In general, the DISPLAY IE is populated according to ISDN communication standards. The NI2 and Euro-ISDN specifications state that the DISPLAY IE should not be populated. This option allows you to override that configuration for your environment.

Add

...

PI to Setup

Panel
bgColor#FAFAFA
borderStylenone

This configuration option enables the ISDN Signaling Group to add/configure a Progress IE to the outbound SETUP message if it is not present. Options are as follows:

  • None (a Progress IE is not added if there is none present, and not modified if present)
  • Not end to end ISDN (call is not end to end ISDN)
  • Destination not ISDN (destination address is not ISDN)
  • Origination not ISDN (originiation address is not ISDN)
  • Return to ISDN (call has returned to the ISDN)
  • Interworking Encountered (interworking has been encountered)
  • Inband Information (in-band information or appropriate pattern now available)
  • Delay Encountered (delay in response at destination interface)

Default entry: None.

Early Media for PI: 2(Dest not ISDN)

Panel
bgColor#FAFAFA
borderStylenone

Defines how PROCEEDING/PROGRESS/ALERT messages are treated for Early Media. Valid options:

Enabled. The PI:2 (Destination not ISDN) value would be treated as if early media was received.in PROCEEDING/PROGRESS/ALERT messages.

Disabled. The PI:2 (Destination not ISDN) value would be treated as if there were no early media received in PROCEEDING/PROGRESS/ALERT messages.

Include Channel Interface

...

identifier

Panel
bgColor#FAFAFA
borderStylenone

Specifies whether to include the Interface Identifier in the Channel Identification Information Element.

...