| Tip |
|---|
Usage of the Easy Config wizard to configure the Sonus SBC 1000/2000 does not modify existing configuration. The wizard will simply add the new configuration elements to the Sonus SBC 1000/2000. |
| Info |
|---|
SBC Easy Configuration supports IPv4 only, not IPv6. |
The Sonus SBC 1000/2000 Easy Config interface includes a built-in step-by-step setup configuration wizard, which enables end-users to quickly deploy Sonus SBC 1000/2000 in an Enterprise's Lync environment with a SIP Trunk Provider to an IP phone. The Sonus SBC 1000/2000 can be configured to use a SIP trunk to connect to IP phones using the automatic setup wizard as described in the section below.
The following SIP Trunks are supported:
- ATT&T IP Flexible Reach
- Generic SIP Trunk
- Verizon Managed Service
- KDDI SIP Trunk
- Broadsoft Trunk
| Note |
|---|
Broadsoft Trunk is applicable only if the user endpoint is an IP phone. |
Depending on the SIP trunk selected, the specific configuration fields are displayed in the Wizard. These are noted below.
Step 1 - Select Scenario
| Note |
|---|
These instructions assume the SBC Easy Config wizard is running. See Running Easy Configuration Wizard. |
Select the Application type (SIP Trunk ↔ IP Phones). Enter the scenario configuration details based on your deployment settings. Once completed, click Next to move to Step 2 (or Cancel to return to the main WebUI screen).
Scenario - Field Definitions
| Section |
|---|
| Column |
|---|
| | Panel |
|---|
| | Caption |
|---|
|  Image Removed
|
|
|
|
Application
| Add_workflow_for_techpubs |
|---|
| AUTH1 | UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} |
|---|
| JIRAIDAUTH | SYM-19713 |
|---|
| REV5 | UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} |
|---|
| REV6 | UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} |
|---|
| REV3 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd700a1f, userName='null'} |
|---|
| REV4 | UserResourceIdentifier{userKey=8a00a0c85c46b657015d4f57d577001c, userName='null'} |
|---|
| REV1 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c7ca0038, userName='null'} |
|---|
|
| Tip |
|---|
Usage of the Easy Config wizard to configure the (SBC) does not modify existing configuration. The wizard will simply add the new configuration elements to the SBC. |
The SBC Easy Config interface includes a built-in step-by-step setup configuration wizard, which enables end-users to quickly deploy SBC in an Enterprise's Lync environment with a SIP Trunk Provider to an IP phone. The SBC can be configured to use a SIP trunk to connect to IP phones using the automatic setup wizard as described in the section below.
The following SIP Trunks are supported:
- ATT SIP Trunk
- KDDI SIP Trunk
- NTT DOCOMO Officelink
- Other SIP Trunk
- SoftBank White Office
- Telstra Enterprise SIP Connect
- Verizon SIP Trunk
- Broadsoft Trunk
| Note |
|---|
NTT DOCOM Officelink, Softbank White Office and Telstra Enterprise SIP Connect are supported in SBC Edge 1000-2000 only. |
| Note |
|---|
Broadsoft Trunk is applicable only if the user endpoint is an IP phone. |
Depending on the SIP trunk selected, the specific configuration fields are displayed in the Wizard. These are noted below.
Step 1 - Select Scenario
| Note |
|---|
These instructions assume the SBC Easy Config wizard is running. See Using the Easy Configuration Wizard. |
Select the Application type (SIP Trunk ↔ IP Phones). Enter the scenario configuration details based on your deployment settings. Once completed, click Next to move to Step 2 (or Cancel to return to the main WebUI screen).
Scenario - Field Definitions
| Caption |
|---|
|
 Image Added
|
Application
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The scenario in which the configuration template is provided. In this case, select SIP Trunk ↔ IP Phones.
|
Scenario Description
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Enter the name to describe the SIP Trunk ↔ IP Phone setup. | Info |
|---|
This value will be prefixed on all the SBC configuration elements created by the Setup Wizard pertaining to this deployment. |
|
Telephone Country
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The country in which the SIP Trunk ↔ IP Phones originates. |
Emergency Services
| Note |
|---|
The E911 Elin number from the "CompanyName" field configured in Lync location services is used as the authoritative Call Back number for outgoing E911 calls, and is always the preferred configuration. Specifically, it will take precedence over any Callback Number number configuration in Lync Setup. For more information, see Creating and Modifying Entries to Transformation Tables. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
This field defines the Emergency Services for outgoing numbers. For the purpose of this illustration above, Emergency Services is not selected. Field definitions are defined below. Options: ELIN Identifier, E911/E112 or None. |
Emergency Callback Number 1
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Call Back Number in string format. This field is displayed only when ELIN Identifier or E911/E112 is selected from Emergency Services. |
Emergency Callback Number 2
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Second Call Back Number in string format. This field is displayed only when ELIN Identifier or E911/E112 is selected from Emergency Services. |
PSAP Number
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Defines the Public Safety Answering Point Number. Valid entry 1 - 127 characters. |
SIP Sessions
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Number of simultaneous SIP sessions allocated. Valid entry 1 - 960. |
Name (SIP Trunk)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The SIP trunk used for connection to the IP phones. Valid options: ATT SIP Trunk, Other SIP Trunk, Verizon SIP Trunk, KDDI SIP Trunk, Broadsoft Trunk, SoftBank White Office, and NTT DOCOMO Officelink. The SIP Trunk selected determines the field options displayed in Step 2. See Step 2 - Configure SIP Details for Endpoint. |
Broadsoft Trunk Type
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Defines the Broadsoft Trunk Type. Valid entry: Enterprise or Access. This field is available only when the SIP Trunk type is Broadsoft Trunk. |
User Type (IP Phone Registrar)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| IP Phone Registrar. This field is fixed. |
Step 2 - Configure SIP Details for Endpoint
Enter the scenario configuration details based on your endpoint. Once completed, click Next to move to Step 3 (or Previous to return to the previous screen).
ATT SIP Trunk - Field Definitions
These fields apply if you selected AT&T IP Flexible Reach in Step 1 - Select Scenario.
| Section |
|---|
| Column |
|---|
| | Panel |
|---|
| | Caption |
|---|
| 0 | Figure |
|---|
| 1 | AT&T IP Flexible Reach |
|---|
|  Image Added
|
|
|
|
Border Element Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The FQDN or IP address of the Session Border Controller service provider. |
Protocol (Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The IP protocol used for sending and receiving SIP messages between SBC and the Border Element Server. Valid entry UDP or TCP. |
Port Number (Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The SIP Server Port number used for sending and receiving SIP messages between SBC and the Border Element Server. |
Use Secondary Border Element Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Enables or disables the secondary Session Border Controller service provider configured. |
Secondary Border Element Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Specifies the Secondary Border Element Service provider. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Border Element Server is Enabled. |
Protocol (Secondary Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled. |
Port Number (Secondary Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Port Number is used for sending and receiving messages between SBC and the Secondary Border Element server. This field is available only when Use Secondary Border Element Server is Enabled. |
AT&T Forking Feature
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Enables/disables AT&T Forking Feature. Valid option: Yes or No. |
AT&T IP Toll Free
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Enables/disables the AT&T Toll Free option. Valid option: Enabled or Disabled. |
IP Toll Free Access Number
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Toll Free Access Number to use when the AT&T IP Toll Free option is enabled. |
IP Phone Numbering Plan
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Selects the IP phone numbering plan to be used. Valid options: E.164, National, or Extension. |
Number of Users
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Define the number of users. Valid entry 1 - 1000. |
Protocol (IP Phone)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the IP phone. Valid entry: UDP or TCP. |
Port Number (IP Phone)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060. |
IP Phone Network Addresses
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Configure a network address and Netmask for the host or subnet in which the IP phone resides. Network IP. IP address for the destination host or subnet in which the IP phone resides. Netmask. The network mask of the destination host or subnet in which the IP phones resides. To create a network address, click the (  Image Added) icon. Enter the Network IP and Network Mask and click OK. |
| Panel |
|---|
|
| Caption |
|---|
|  Image Added
|
|
KDDI SIP Trunk - Field Definitions
These fields apply if you selected KDDI SIP Trunk in Step 1 - Select Scenario.
| Section |
|---|
| Column |
|---|
| | Panel |
|---|
| | Caption |
|---|
| 0 | Figure |
|---|
| 1 | KDDI SIP Trunk |
|---|
| 3 | KDDI SIP Trunk |
|---|
|  Image Added
|
|
|
|
SIP Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| The FQDN or IP address of the Session Border Controller service provider. |
Protocol
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| The IP protocol used for sending and receiving SIP messages between SBC and the Border Element Server. Valid entry UDP or TCP. |
Port Number
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| The SIP Server Port number used for sending and receiving SIP messages between SBC and the Border Element Server. |
Called Prefix
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Used for setting up transformation rules for the FMC service.
|
Address of Record URI
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Address of Record of the client that is registered on the SIP server.
|
Static Host
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Address of Static Host. Valid options: FQDN[:port] or IP4 [:port] or [IP6]:port |
Authentication ID
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Specifies a user name to use in response to a challenge.
|
Enter Password
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| The password for the Authentication ID. |
Confirm Password
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Re-enter the password for the Authentication ID.
|
DNS Server IP
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| IP address (IPv4 or IPv6) of the DNS server. |
Domain Name
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Domain name associated with the DNS IP address. |
IP Phone Numbering Plan
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Selects the IP phone numbering plan to be used. Valid options: E.164, National, or Extension. |
Number of Users
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The scenario in which the configuration template is provided. In this case, select SIP Trunk ↔ IP Phones.
|
...
| Define the number of users. Valid entry 1 - 1000. |
Protocol (IP Phone)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Enter the name to describe the SIP Trunk ↔ IP Phone setup. | Info |
|---|
This value will be prefixed on all the Sonus SBC 1000/2000 configuration elements created by the Setup Wizard pertaining to this deployment. |
|
...
| The Protocol used for communicating with the IP phone. Valid entry: UDP or TCP. |
Port Number (IP Phone)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The country in which the SIP Trunk ↔ IP Phones originates. |
Emergency Services
| Note |
|---|
The E911 Elin number from the "CompanyName" field configured in Lync location services is used as the authoritative Call Back number for outgoing E911 calls, and is always the preferred configuration. Specifically, it will take precedence over any Callback Number number configuration in Lync Setup. For more information, see Creating and Modifying Entries to Transformation Tables. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Defines the Emergency Services for outgoing numbers. For the purpose of this illustration above, Emergency Services is not selected. Field definitions are defined below. Options: ELIN Identifier, E911/E112 or None. |
Emergency Callback Number 1
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Call Back Number in string format. This field is displayed only when ELIN Identifier or E911/E112 is selected from Emergency Services. |
Emergency Callback Number 2
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Second Call Back Number in string format. This field is displayed only when ELIN Identifier or E911/E112 is selected from Emergency Services. |
| The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060. |
IP Phone Network Addresses
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Configure a network address and Netmask for the host or subnet in which the IP phone resides. Network IP. IP address for the destination host or subnet in which the IP phone resides. Netmask. The network mask of the destination host or subnet in which the IP phones resides. To create a network address, click the ( Image Added) icon. Enter the Network IP and Network Mask and click OK. | Caption |
|---|
| Image Added |
|
NTT DOCOMO Officelink - Field Definitions
These fields apply if you selected NTT DOCOMO Officelink Trunk in Step 1 - Select Scenario.
| Note |
|---|
For an IP Phone as the user end point, Easy Configuration loads a generic template which follows the “National Numbering Plan” guidelines. |
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | NTT DOCOMO Officelink Trunk |
|---|
|
 Image Added |
Office Link FOMA-R
...
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Defines the Public Safety Answering Point Number. Valid entry 1 - 127 characters. |
...
| The Host IP address of the SIP Server. |
Protocol
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Number of simultaneous SIP sessions allocated. Valid entry 1 - 960. |
...
| The IP protocol used for sending and receiving SIP messages between SBC and the SIP Server. Default value: UDP. |
Port
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| The The SIP trunk Server Port number used for connection to the IP phones. Valid options: Generic SIP Trunk, AT&T IP Flexible Reach, Verizon Managed Service, and Broadsoft Trunk. The SIP Trunk selected determines the field options displayed in Step 2. See Step 2 - Configure SIP Details for Endpoint. |
...
| sending and receiving SIP messages between the SBC and the SIP Server. Default value: 5062. |
CUG Domain Name
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| The FQDN of the SIP Server. |
IP Phone Numbering Plan
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Defines the Broadsoft Trunk TypeIP phone numbering plan to be used. Valid entryoptions: Enterprise or Access. This field is available only when the SIP Trunk type is Broadsoft Trunk. |
...
E.164, National, or Extension. |
Number of Users
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| IP Phone Registrar. This field is fixed. |
Step 2 - Configure SIP Details for Endpoint
Enter the scenario configuration details based on your endpoint. Once completed, click Next to move to Step 3 (or Previous to return to the previous screen).
Generic SIP Trunk - Field Definitions
These fields apply if you selected Generic SIP Trunk in Step 1 - Select Scenario.
| Section |
|---|
| Column |
|---|
| | Panel |
|---|
| | Caption |
|---|
| 0 | Figure |
|---|
| 1 | Generic SIP Trunk |
|---|
|  Image Removed
|
|
|
|
Border Element Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The FQDN or IP address of the Session Border Controller service provider. |
Protocol (Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The IP protocol to use for sending and receiving SIP messages between Sonus SBC 1000/2000 and the Border Element Server. Valid entry UDP or TCP. |
Port Number (Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The SIP Server Port number used for sending and receiving SIP messages between Sonus SBC 1000/2000 and the Border Element Server. |
Use Secondary Border Element Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Enables or disables the secondary Session Border Controller service provider configured. |
...
| Defines the number of users. Valid entry 1 - 1000. |
Protocol (IP Phone)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the IP phone. Valid entry: UDP or TCP. |
Port Number
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060. |
IP Phone Network Addresses
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Configure a network address and Netmask for the host or subnet in in which the IP phones reside. - Network IP. IP address for the destination host or subnet in which the IP phone resides.
- Netmask. The network mask of the destination host or subnet in which the IP phones resides.
To create a network address, click the ( Image Added) icon. Enter the Network IP and Network Mask and click OK. | Caption |
|---|
| Image Added |
|
Other SIP Trunk - Field Definitions
These fields apply if you selected Generic SIP Trunk in Step 1 - Select Scenario.
| Section |
|---|
| Column |
|---|
| | Panel |
|---|
| | Caption |
|---|
|  Image Added
|
|
|
|
Border Element Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Specifies the Secondary Border Element Service provider. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Border Element Server is Enabled. |
...
The FQDN or IP address of the Session Border Controller service provider. |
Protocol (Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the Secondary IP protocol to use for sending and receiving SIP messages between SBC and the Border Element Server. Valid entry : UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled. |
Port Number (
...
Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The SIP Server Port Number number used for sending and receiving SIP messages between Sonus SBC 1000/2000 and the Secondary Border Element server. This field is available only when Server. |
Use Secondary Border Element Server
...
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Defines the IP phone numbering plan to be used. Valid options: E.164, National, or Extension. |
...
|
Enables or disables the secondary Session Border Controller service provider configured. |
Secondary Border Element Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Defines the number of users. Valid entry 1 - 1000 Specifies the Secondary Border Element Service provider. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Border Element Server is Enabled. |
Protocol (
...
Secondary Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the IP phone. Secondary Border Element Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled. |
Port Number (
...
Secondary Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Port Number used for sending and receiving messages between Sonus SBC 1000/2000 and the IP phone. Default entry: 5060. |
...
Secondary Border Element server. This field is available only when Use Secondary Border Element Server is Enabled. |
IP Phone Numbering Plan
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Defines the IP phone numbering plan to be used. Valid options: E.164, National, or Extension. |
Number of Users
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Configure a network address and Netmask for the host or subnet in in which the IP phones reside. Network IP. IP address for the destination host or subnet in which the IP phone resides. Netmask. The network mask of the destination host or subnet in which the IP phones resides. To create a network address, click the (  Image Removed) icon. Enter the Network IP and Network Mask and click OK. | Caption |
|---|
| Image Removed |
|
AT&T IP Flexible Reach - Field Definitions
These fields apply if you selected AT&T IP Flexible Reach in Step 1 - Select Scenario.
| Section |
|---|
| Column |
|---|
| | Panel |
|---|
| | Caption |
|---|
| 0 | Figure |
|---|
| 1 | AT&T IP Flexible Reach |
|---|
|  Image Removed
|
|
|
|
Border Element Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The FQDN or IP address of the Session Border Controller service provider. |
Protocol (Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The IP protocol used for sending and receiving SIP messages between Sonus SBC 1000/2000 and the Border Element Server. Valid entry UDP or TCP. |
Port Number (Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The SIP Server Port number used for sending and receiving SIP messages between Sonus SBC 1000/2000 and the Border Element Server. |
Use Secondary Border Element Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Enables or disables the secondary Session Border Controller service provider configured. |
...
| Defines the number of users. Valid entry 1 - 1000. |
Protocol (IP Phone)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the IP phone. Valid entry: UDP or TCP. |
Port Number (IP Phone)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Port Number used for sending and receiving messages between SBC and the IP phone. Default entry: 5060. |
IP Phone Network Addresses
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Configure a network address and Netmask for the host or subnet in in which the IP phones reside. Network IP. IP address for the destination host or subnet in which the IP phone resides. Netmask. The network mask of the destination host or subnet in which the IP phones resides. To create a network address, click the ( Image Added) icon. Enter the Network IP and Network Mask and click OK. | Caption |
|---|
|  Image Added
|
|
SoftBank White Office - Field Definitions
These fields apply if you selected SoftBank White Office in Step 1 - Select Scenario.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | SoftBank White Office |
|---|
|
 Image Added
|
WAN Link
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Specifies the Secondary Border Element Service provider. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Border Element Server is Enabled. |
...
The method used for connecting networks. Options are: Routerless and Router. On selection of Routerless, the Easy Config displays the Signaling/Media Source IP field and the SIP Server field. On selection of Router, the Easy Config displays the SIP Server field only. |
Signaling/Media Source IP
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled. |
...
user-specified IP address to be used for SIP signaling messages. The Signaling/Media Source IP field does not display when the option selected for the WAN Link field is Router. |
SIP Server
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Port Number is used for sending and receiving messages between Sonus SBC 1000/2000 and the Secondary Border Element server. This field is available only when Use Secondary Border Element Server is Enabled. |
...
host IP address or FQDN for the SIP server. |
Gateway ID
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The ID used for authenticating with the router at the gateway of the network. |
Gateway Password
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Enables/disables AT&T Forking Feature. Valid option: Yes or No. |
...
The password used for authenticating with the router at the gateway of the network. |
Confirm Password
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Enables/disables the AT&T Toll Free option. Valid option: Enabled or Disabled. |
...
Re-entry of the password for the router serving as the network gateway. |
Address of Record URI
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Toll Free Access Number to use when the AT&T IP Toll Free option is enabledpublic address that points to the domain for users, for use in the Contact Registrant Entry. For example, specify: GatewayID@SIPServer. |
IP Phone Numbering Plan
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Selects Defines the IP phone numbering plan to be used. Valid options: E.164, National, or Extension. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Define Defines the number of users. Valid entry 1 - 1000. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the IP phone. Valid entry: UDP or TCP. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Port Number used for sending and receiving messages between Sonus SBC 1000/2000 SBC and the IP phone. Default entry: 5060. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Configure a network address and Netmask for the host or subnet in in which the IP phone residesphones reside. Network IP. IP address for the destination host or subnet in which the IP phone resides. Netmask. The network mask of the destination host or subnet in which the IP phones resides. To create a network address, click the ( Image Removed Image Added) icon. Enter the Network IP and Network Mask and click OK. |
| Panel |
|---|
|
| Caption |
|---|
| Image Modified |
|
...
Telstra Enterprise SIP Connect - Field Definitions
These fields apply if you selected Verizon Managed Service in Telstra Enterprise SIP Connect in Step 1 - Select Scenario.
...
...
...
Image Removed
...
| Telstra Enterprise SIP Connect Trunk |
|
 Image Added
|
NAT Public Interface
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The FQDN or IP address of the Session Border Controller service provider. |
...
public interface used for Network Address Translation (NAT). |
State
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The IP protocol used for sending and receiving SIP messages between Sonus SBC 1000/2000 and the Border Element Server. This value is fixed at UDP. |
...
state to use in configuring the outbound proxy for the Provider SIP Trunk. Options include: Australia Capital Territory, New South Wales, Northern Territory, Queensland, South Australia, Tasmania, Victoria, and Other (a user-specified FQDN). |
Protocol and Port
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The SIP Server Port number used for sending and receiving SIP messages between Sonus SBC 1000/2000 and the Border Element Server. |
...
Hard coded as UDP and Port 5060. |
SIP Connect DNS IP
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Selects the IP phone numbering plan to be used. Valid options: E.164, National, or Extension. |
...
The IPv4 address used to create a Split DNS entry for the Telstra domain. |
SIP Connect Domain/Realm
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Define the number of users. Valid entry 1 - 1000. |
...
The SIP Connect Domain or Realm to which the specified IP address will map. |
Authentication User ID
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the IP phone. Valid entry: UDP or TCP. |
...
User ID for use in authentication. |
Authentication Password
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Port Number used for sending and receiving messages between Sonus SBC 1000/2000 and the IP phone. Default entry: 5060. |
...
password to use when authenticating with the User ID. |
Confirm Password
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Configure a network address and Netmask for the host or subnet in which the IP phone resides. Network IP. IP address for the destination host or subnet in which the IP phone resides. Netmask. The network mask of the destination host or subnet in which the IP phones resides. To create a network address, click the ( Image Removed) icon. Enter the Network IP and Network Mask and click OK. |
| Panel |
|---|
|
| Caption |
|---|
| Image Removed |
|
KDDI SIP Trunk - Field Definitions
These fields apply if you selected KDDI SIP Trunk in Step 1 - Select Scenario.
Image RemovedThe re-entered password for confirmation. |
Trunk Pilot Number
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The 9-digit pilot number Telstra assigned for use with the SIP Connect trunking service. |
IP Phone Numbering Plan
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Defines the IP phone numbering plan to be used. Valid options: E.164, National, or Extension. |
Number of Users
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Defines the number of users. Valid entry 1 - 1000. |
Protocol (IP Phone)
...
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| The FQDN or IP address of the Session Border Controller service provider. |
...
The Protocol used for communicating with the IP phone. Valid entry: UDP or TCP. |
Port Number (IP Phone)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The IP protocol Port Number used for sending and receiving SIP messages between Sonus SBC 1000/2000 and the Border Element Server. Valid entry UDP or TCP. |
...
IP phone. Default entry: 5060. |
IP Phone Network Addresses
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Configure a network address and Netmask for the host or subnet in in which the IP phones reside. |
| The SIP Server Port number used for sending and receiving SIP messages between Sonus SBC 1000/2000 and the Border Element Server. |
Call Prefix
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| ??? |
Address of Record URI
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| ??? |
Static Host
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Address of Static Host. Valid options: FQDN[:port] or IP4 [:port] or [IP6]:port |
Authentication ID
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| ??? |
Network IP. IP address for the destination host or subnet in which the IP phone resides. Netmask. The network mask of the destination host or subnet in which the IP phones resides. To create a network address, click the ( Image Added) icon. Enter the Network IP and Network Mask and click OK. | Caption |
|---|
| Image Added |
|
Verizon SIP Trunk - Field Definitions
These fields apply if you selected Verizon Managed Service in Step 1 - Select Scenario.
| Section |
|---|
| Column |
|---|
| | Panel |
|---|
| | Caption |
|---|
| 0 | Figure |
|---|
| 1 | Verizon Managed Service |
|---|
| Image Added |
|
|
|
Border Element Server
...
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| ??? |
...
The FQDN or IP address of the Session Border Controller service provider. |
Protocol (Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| ??? |
...
The IP protocol used for sending and receiving SIP messages between SBC and the Border Element Server. This value is fixed at UDP. |
Port Number (Border Element Server)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| IP address (IPv4 or IPv6) of the DNS server. |
Domain Name
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Domain name associated with the DNS IP address The SIP Server Port number used for sending and receiving SIP messages between SBC and the Border Element Server. |
IP Phone Numbering Plan
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Selects the IP phone numbering plan to be used. Valid options: E.164, National, or Extension. |
Number of Users
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Define Define the number of users. Valid entry 1 - 1000. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the IP phone. Valid entry: UDP or TCP. |
Port Number (IP Phone)
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| The The Port Number used for sending and receiving messages between Sonus SBC 1000/2000 and the IP phone. Default entry: 5060. |
IP Phone Network Addresses
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Configure a network address and Netmask for the host or subnet in which the IP phone resides. Network IP. IP address for the destination host or subnet in which the IP phone resides. Netmask. The network mask of the destination host or subnet in which the IP phones resides. To create a network address, click the ( Image Removed Image Added) icon. Enter the Network IP and Network Mask and click OK. |
| Panel |
|---|
|
| Caption |
|---|
| Image RemovedImage Added |
|
noprint
...
Back to top
Broadsoft Trunk - Field Definitions
...
| Section |
|---|
| Column |
|---|
| | Panel |
|---|
| | Caption |
|---|
|  Image RemovedImage Added
|
|
|
|
Server Domain
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The FQDN of the server domain. |
...
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Enables/disables Enterprise Trunking. This field is available only when Enterprise Trunking is selected in the Broadsoft Trunk Type field. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Selects the IP phone numbering plan to be used. Valid options: E.164, National, or Extension. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
| Define the number of users. Valid entry 1 - 1000. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Protocol used for communicating with the IP phone. Valid entry: UDP or TCP. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
The Port Number used for sending and receiving messages between Sonus SBC 1000/2000 and the IP phone. Default entry: 5060. |
| Panel |
|---|
| bgColor | #FAFAFA |
|---|
| borderStyle | none |
|---|
|
Configure a network address and Netmask for the host or subnet in which the IP phone resides. Network IP. IP address for the destination host or subnet in which the IP phone resides. Netmask. The network mask of the destination host or subnet in which the IP phones resides. To create a network address, click the ( Image Removed Image Added) icon. Enter the Network IP and Network Mask and click OK. | Caption |
|---|
| Image Removed |
|
| Noprint |
|---|
Back to topImage Added |
|
Step 3 - Confirm and Submit Configuration
...
| Section |
|---|
| Column |
|---|
| | Panel |
|---|
| | Caption |
|---|
| Image Added Image Removed |
|
|
|