Page History

Internal_display_only

sbsarkar

Add_workflow_for_techpubs

AUTH2

AUTH1	pmuthuUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca7f046c, userName='null'}
REV5	bscogginsUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909df, userName='null'}
REV6	bscogginsUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909df, userName='null'}
REV3	gswamyUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c90601df, userName='null'}
REV1	ggundluriUserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cbba0641, userName='null'}

panel

Panel

In this Section:

Table of Contents

To Configure

Earlier, in

Spacevars

0	series

/

Spacevars

0	series2

, only the management interface group was used to handle the external PSX traffic. Now, the Packet Interfaces handle the external PSX traffic. The following three new parameters are added to Global Configuration of Policy Server as an enhancement:

type
addressContext
interfacesGroupId

To View and Edit

Global Config

On the SBC main screen, go navigate to Configuration > System Setup >Policy Server > Global Config. The Global Config window is displayed.

Type: ip

By default, the Edit Global Config window is displayed with the parameter Type as set to Mgmt.

Caption

0	Figure
1	Policy Server - Global Config MgmtIP

Image Added

Image Removed

Type: mgmt
When you set the parameter Type to IP, some additional parameters are displayed.
Caption
0 Figure
1 Policy Server - Global Config IPMgmt
Image Added

Image Removed
Make the required changes and click Save to save the changesconfiguration, or Clear to cancel them.
The following fields parameters displayed are displayed:
Caption
0 Table
1 Policy Server - Global Config parameters

type "ip"NOTE: This parameter is only visible when the attribute, type is set to "ip".
Specifies all the valid Management Interface Groups available to communicate with external PSX.
This parameter is only visible when the attribute, type is set to "mgmt"
Parameter
Length/Range
Description
Reconnect Timeout
1-3600
Specifies the time interval in seconds for re-attempting the connection to Policy Server which is in the enabled state. The value ranges from 1 - 3600 seconds and the default value is
Default value: 10 seconds.
Switch Over Mode N/A
Specifies the means to connect to the active Policy Server. The options are:
automaticAutomatic: Retries to the previously ACTIVE Policy Server after a switch over
manualManual: Does not retry to connect after a switch over.
Congestion Control Control
N/A
When enabled, SBC throttles the sending or Policy Requests to either active or standby PSX. The options are:
disabled Disabled (default)
enabledEnabled
Type
N/A
Specifies the type of Interface Group used. The options are:
mgmtMgmt (default)ip
IP
Mgmt Interface Group N/A
Specifies all the valid Management Interface Groups available to communicate with external PSX.
NOTE: This parameter is only visible when the attribute, Type is set to Mgmt.
Address Context N/A
Specifies all the valid Address Contexts.
Note
NOTE: This parameter is only visible when the attribute, Type is set to IP.
Ip IP Interface Group N/A
Specifies all the valid IP Interface Group that belongs to the configured Address Contexts.
Note
Mgmt Interface Group
Note
Type is set to IP.
IP Var 1-255
Use this parameter to specify a metavarible name (from the PSX’s metavariable table) used to provide an IP address for the SBC SWe Cloud for connecting to the PSX. When the IP Var field is blank, the SBC SWe Cloud picks any random IP address from the configured interface to connect to the PSX.

NOTE: Use this parameter for SBC SWe Cloud configurations only.
SBC Gateway Name N/A The name of the SBC gateway that processes the request.
DNS Group N/A
The name of the DNS group to associate with the policy server global configuration to allow PSX FQDN resolution with a particular DNS group.
Refer to Configuring DNS Groups for a configuration example.
To View Policy Server Status
On the navigation pane, navigate to Monitoring > Dashboard > System Status > Policy Server Status.
Caption
0 Figure
1 Policy Server Status
Image Added

For parameter descriptions, refer to Policy Server section in Show Status System page.

Pagebreak

Space shortcuts

Page tree

Versions Compared

Old Version 4

New Version Current

Key

To Configure

Global Config

Type: ip

To View Policy Server Status

Parameter	Length/Range	Description
`Reconnect Timeout`	1-3600	Specifies the time interval in seconds for re-attempting the connection to Policy Server which is in the enabled state. The value ranges from 1 - 3600 seconds and the default value is Default value: 10 seconds.
`Switch Over Mode`	N/A	Specifies the means to connect to the active Policy Server. The options are: `automaticAutomatic`: Retries to the previously ACTIVE Policy Server after a switch over `manualManual`: Does not retry to connect after a switch over.
`Congestion` Control `Control`	N/A	When enabled, SBC throttles the sending or Policy Requests to either active or standby PSX. The options are: `disabled` `Disabled` (default) `enabledEnabled`
`Type`	N/A	Specifies the type of Interface Group used. The options are: `mgmtMgmt` (default)`ip` `IP`
`Mgmt Interface Group`	N/A	Specifies all the valid Management Interface Groups available to communicate with external PSX. NOTE: This parameter is only visible when the attribute, `Type` is set to `Mgmt`.
`Address Context`	N/A	Specifies all the valid Address Contexts.
Note
NOTE: This parameter is only visible when the attribute,	`Type` is set to	`IP`.
Ip `IP Interface Group`	N/A	Specifies all the valid IP Interface Group that belongs to the configured Address Contexts.
Note
`Mgmt Interface Group`
Note
`Type` is set to `IP`.
`IP Var`	1-255	Use this parameter to specify a metavarible name (from the PSX’s metavariable table) used to provide an IP address for the SBC SWe Cloud for connecting to the PSX. When the `IP Var` field is blank, the SBC SWe Cloud picks any random IP address from the configured interface to connect to the PSX. NOTE: Use this parameter for SBC SWe Cloud configurations only.
`SBC Gateway Name`	N/A	The name of the SBC gateway that processes the request.
`DNS Group`	N/A	The name of the DNS group to associate with the policy server global configuration to allow PSX FQDN resolution with a particular DNS group. Refer to Configuring DNS Groups for a configuration example.