Include Page |
---|
|
add |
docset |
workflowAUTH2 | jharvey |
---|
AUTH1 | jharvey |
---|
DEV1 | jharvey |
---|
LDEV1 | jharvey |
---|
SVT1 | jharvey |
---|
LSVT1 | jharvey |
---|
|
|
...
This technical guide shows how to configure the SBC Edge with a Tenor AF/AX for fax connection.
This document provides basic guidelines, and assumes the user has a working knowledge of the following products:
- The SBC 1000/2000
- Tenor AFM200
Deployed software versions in this document are:
...
Basic configuration information for these products can be found in the Best Practices section.
Configure
...
the (SBC)
Note |
---|
This procedure detailing configuration of the SBC 1000/2000 and Tenor AFM200 assumes configuration in the country of France using G711A / G.711A / a-law. Other countries such as USA and Japan use the corresponding G711U / G.711U / µ-Law. Verify you are using the proper protocol for the country in which the configuration is taking place. |
...
Perform the steps below to configure the SBC 1000/2000 for the interconnection scenario.
Use the SBC 1000 web interface and search for the objects below to help with navigation.
...
Note |
---|
The T.38 protocol optimizes the interconnection reliability of a fax over IP networks. |
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | T38 Media Profile |
---|
|
|
|
...
SIP Registrar Table
- Create an SBC 1000/2000 SIP Registrar table so the Tenor can register each of its analog ports as a SIP User Agent into the SBC 1000/2000.
- Enter as many number of Users as expected analog ports to be registered:
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Creating a SIP Registration Table |
---|
|
|
|
Tenor Call Routing Table
Create a Call Routing Table for Tenor, as shown below to route a fax call from Tenor to PSTN through the SBC Edge.
...
- Create the Tenor SIP Signaling Group which allows the SBC 1000/2000 to send and receive SIP calls to/from the Tenor with the following parameters (created previously).
- Verify that the values in the Port and Protocol fields in the Listen Ports panel configured for the Tenor are the same when configuring the SBC1000/2000.
...
Create a dedicated transformation table to be able to receive a fax on the SBC 1000 and forward it to the Tenor, depending on the fax numbers to be routed from the SBC 1000 to Tenor.
Info |
---|
For example, to route all calls from extension range 1xxx to Tenor, enter similar data in the Description field as shown in figure below. |
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Creating a Dedicated Tenor Transformation Table |
---|
|
|
|
...
Panel |
---|
|
Caption |
---|
|
|
|
- Select Confirm/OK after making changes.
- Select the "red star button" to apply changes to the Tenor:
...
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | SIP Signaling Group 1 of 3 |
---|
|
|
|
On the Advanced tab, make sure the protocol matches the one configured previously in the Tenor Signaling Group:
...
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Edit User Agent 1 of 2 |
---|
|
|
|
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Edit User Agent 2 of 2 |
---|
|
|
|
...
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Edit DN Channel Map 2 of 2 |
---|
|
|
|
Codec
Enter at least one G.711A codec:
...
Verify the fax section of the IP Routing Group menu is configured as shown below, and matches what was created on the SBC 1000/2000 for the T.38 codec:
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | IP Routing Group-default |
---|
|
|
|
...
- Select the Advanced Explore tab.
- Expand VoIP Configuration.
- Select Gateway.
Check the Use Routing Table checkbox, if it is not already checked.
Note |
---|
The system will ask for a backup and reboot if this is the first time the Routing Table mode is activated. |
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Number Table-Tenor-SBC 1 of 2 |
---|
|
|
|
...
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Number Table-Tenor-SBC 2 of 2 |
---|
|
|
|
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Number Table - New |
---|
|
|
|
...
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Edit Routing Table Entry 1 of 2 |
---|
|
|
|
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | Edit Routing Table Entry 2 of 2 |
---|
|
|
|
These tables only look for and can adapt the called number in the above example, but you can also adapt the calling number.