Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca7f046c2c909b309109945b01912fd89e540006, userName='null'}
JIRAIDAUTHSBX-88873127240
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e98a00a02355cd1c2f0155cd26cd5909df, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a0c8606235800160682f2d6800018a00a0c8674c8a57016753eb895d0007, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c90701ea8a00a0c8674c8a57016753eb895d0007, userName='null'}



Panel

In this section:

Table of Contents
maxLevel2



Info
iconfalse

Related articles:

Children Display


This object displays the user-configured LI Call Data Control Channel.

To

View the Call Data Channel

To view the Call Data Channel, log on as a "Calea" user. For more information, refer to Users and Application Management - User and Session Management.

On the SBC main screen, navigate to Configuration > Intercept > Call Data Channel.

The Call Data Channel can be checked for default Address Context. Use the drop-down box to select the default Address Context .The and open the Call Data Channel window is displayed.

To

Edit the Call Data Channel

To edit any of the Call Data Channel Channels in the list, click the radio button next to the specific Call Data Channel name. The This opens the Edit Selected Call Data Channel window is displayed below.


Make the required changes and then click Save.

To

Create a Call Data Channel

To create a new Call Data Channel, click the New Call Data Channel tab on the Call the Call Data Channel List panel. The This opens the Create New Call Data Channel window is displayed.

Image Removed

Info
titleNote

The displayed fields depend on the values selected for Intercept Standard and Vendor ID fields. If a parameter is visible, then it is supported for that LI configuration.


Before proceeding to create an LI configuration, note the following LI flavors and configuration, which are possible with different combinations of Intercept Standard and parameter values.

Anchor
InterceptFlavors
InterceptFlavors
 
Intercept Flavors and Configuration Details

Configuration Settings


LI Flavor/Characteristic

Intercept Standard
Vendor ID
PacketcableNone/Group Two Thousand/Utimaco/Verint Legacy LI (default)
PacketcableSs8PCSI LI
Three Gpp/Etsi

None/Group Two Thousand/Utimaco/Verint

IMS LI


Use Refer to Intercept Flavors and Configuration Details to decide a configuration and set the parameter values accordingly. For value for the desired configuration. For example, select Packetcable as the Intercept Standard and Ss8 as the Vendor ID to set PCSI LI configuration.


Call Data Channel Parameters

Use the to Use the to

Parameter

Description

Name

Specifies the name of the IP interface group used to stream to the LI Server.

Intercept Standard

Specifies the intercept standard used. The options are:

  • Etsi
  • Packetcable  (default)
  • Three Gpp

Refer to Intercept Flavors and Configuration Details

 to set the value for the desired configuration.

Vendor ID

Specifies the vendor of the LI server used. The options are:

  • None (default)
  • Group Two Thousand
  • Ss8
  • Utimaco
  • Verint

Refer to Intercept Flavors and Configuration Details

 to set the value for the desired configuration.


Info
titleNote

The remaining parameters depend on the values selected for Intercept Standard and Vendor ID parameters. If a parameter is visible, then it is supported for that LI configuration.


Pri State

Specifies if the communication to the primary LI Server is enabled or not.

  • Disabled (default)
  • Enabled

Sec State

Specifies if the communication to secondary LI Server is enabled or not.

  • Disabled (default)
  • Enabled

Pri Mode

Specifies the mode of the primary server.

  • Active
  • Standby
  • Out of service (default)

Sec Mode

Specifies the mode of the secondary server.

  • Active
  • Standby
  • Out of service (default)

Pri IP Address

Specifies the primary LI Server's IP address where Call Data Channel messages are sent. Default - 0.0.0.0

Sec IP Address

Specifies the secondary LI Server's IP address where Call Data Channel messages are sent. Default - 0.0.0.0

Pri Port

Specifies the primary LI Server's UDP port where Call Data Channel messages are sent. Default - 0

Ka Timer

Specifies the Keep Alive Timer in seconds. Default - 5

Retries

Specifies the number of retries before LI Call Data Channel is considered failed. Default - 3

IP Interface Group Name

Specifies the name of the IP interface group used to stream to the LI Server.

Li Pol Dip For Regd Ood Msg

Specifies that the policy dip to PSX for the Out-Of-Dialog messages of the registered user is enabled or not.

  • Disabled (default)
  • Enabled
RTCP InterceptionThis flag indicates whether RTCP information is intercepted or not.
  • Disabled (default)
  • Enabled
Media IP Interface Group NameThe name (1-23 characters) of the IP interface group that is used to stream media packets to the LI server.
Dsr Protocol Version

Signifies the intercepted X2 signaling protocol version towards the mediation servers. The default value 0 maintains backward compatibility with SBC Core 8.0 or earlier

  • 0 (default)
  • 1
SIP Trunk Group Supported List

Sip Trunk Group Exempted List

Trunk Groups with CALEA-compliant lawful intercept (LI) rules may intercept a call on each leg of the call. To prevent this, you can identify a specified leg of a relevant trunk group (TG) to either a Supported TG List, or to an Exempted TG List, assuring that calls are only intercepted once.

These are mutually exclusive lists, and entries can only appear on one list, never both. Entries on these lists are leaf references to SIP TGs that apply across the entire system, and will apply to all addressContext objects and zones.

Select pre-configured trunk groups from the drop-down menu.

Available_since
TypeAvailable Since
Release12.1.4


Copy a Call Data Channel

Info
titleNote

The user calea with the role "Calea" is not allowed to perform the "Copy" operation.

To

Delete a Call Data Channel

Info
titleNote

If the Call Data Channel which you wish to delete is configured for PCSI or IMS, then ensure the following before performing the below this procedure. 

  • Media and Signaling (for IMS configuration only) mode are Out of Service.
  • Media and Signaling (for IMS configuration only) state are Disabled.

Refer Media - TCP and Media - UDP to and Media - TLS to edit media profile and Mediation Server - Signaling to edit signaling.


To delete any of the created Call Data Channel, click the radio button next to the specific Call Data Channel.

Click Delete at the end of the highlighted row . A and respond to the delete confirmation message appears seeking your decision.

Click Yes to remove the specific Call Data Channel from the list.