Add_workflow_for_techpubs |
---|
AUTH1 | UserResourceIdentifier{userKey=8a00a0c86e9b2550016ec54396b5000a8a00a02355cd1c2f0155cd26cd5909df, userName='null'} |
---|
JIRAIDAUTH | SBX-1109431134133 |
---|
REV5 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e98a00a02355cd1c2f0155cd26cd5909df, userName='null'} |
---|
REV6 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e98a00a02355cd1c2f0155cd26cd5909df, userName='null'} |
---|
REV3 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cbfd06fb8a00a0c86573c09001659db4327e0018, userName='null'} |
---|
REV1 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cbfd06fb8a00a0c86573c09001659db4327e0018, userName='null'} |
---|
|
Include Page |
---|
| _Clear_upgrade_directory_warning |
---|
| _Clear_upgrade_directory_warning |
---|
|
Include Page |
---|
_Clear_upgrade_directory_warning | _Clear_upgrade_directory_warning | Info |
---|
|
To recover from the default indices, refer to Recovering from Default Indices in 1:1 HA SBC SWe, if applicable.This section describes the different methods to upgrade
the the
(SBC 7000 series and SBC SWe) application application.
When an
upgrade is available, the software is posted on the Ribbon Support Portal. Refer to
Downloading Software from the Ribbon Support Portal for more information.
Prerequisities
Prior to performing an upgrade on the
, ensure the following activies are accomplished.
For SBC Core (in general)
:For :
SBC SWe
Info |
---|
|
The E1000E network interface type is unsupported in VMware. |
On setups, the active node takes more time than expected for the services to come up after an upgrade from 11.1.0x. Before performing an upgrade from 11.1.0x, apply the following steps:
- Confirm that the cnixpmadmin password is not default by running the following command as root on the active and standby nodes:
Code Block |
---|
[root@SBC]# $ENCRYPTED_STORE_SH cnxipmadmin |
Info |
---|
|
The command must not show the default password "Cnx1PmAdm1n " |
- If the password is still the default, randomize the password by running the following command as root on the active node:
Code Block |
---|
[root@SBC]# $CHANGE_DEFAULT_PASSWDS_SH |
- Verify the cnxipmadmin password is updated to a random one on both the active and standby nodes:
Code Block |
---|
[root@SBC]# $ENCRYPTED_STORE_SH cnxipmadmin |
Live Software Upgrade (LSWU)
LSWU allows a user users to upgrade the
application application software on HA pairs without impacting service (dropping calls). This is mainly recommended for HA SBC systems. You can also perform a an LSWU on the the EMA and in EMA Platform Mode. Refer to Live Software Upgrade using CLI and System Administration - Software Install-Upgrade for more information.Non-Live Software Upgrade (Non-LSWU)
The non-LSWU upgrade process requires taking the SBC system offline to perform an application upgrade. This refers to upgrading the
application in a standalone or HA configuration using EMA Platform Mode. Refer to Upgrading SBC Application using EMA Platform Mode for more information.
Info |
---|
|
Once the upgrade is complete, rediscover the SBC from the EMS/RAMP, if present, and edit any modified attributes that may have been modified post-upgrade. Attributes are listed under the EMS page at: . |
pagebreakIf the SBC is configured and registered in RAMP, the connection may be lost after the first server upgrade. RAMP may take time to show the SBC as Registered again until both servers are completely upgraded. |