Versions Compared

Old Version 2

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
JIRAIDAUTHSYM-23168
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ce320b29, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ce340b42, userName='null'}

Include Page
Not_for_SWe
Not_for_SWe

To create or modify an existing ISDN Signaling Group:

  1. Click the expand (Image Added) icon next to the entry you wish to modify.
  2. Edit the entry properties as required.

Excerpt IncludeManaging ISDN Signaling GroupsManaging ISDN Signaling GroupsnopaneltrueModifying an ISDN Signaling Group Include Page_Modify_Entry_Modify_Entrynopaneltrue

  1. Click the expand (Image Added) icon next to the entry you wish to modify.
  2. Edit the entry properties as required.

BRI vs. PRI (T1) Ports

...

width750px

There is a subtle but very important difference in the UI between ISDN/BRI (Basic Rate Interface) Signaling Groups and ISDN/PRI (Primary Rate Interface) Signaling Groups. These differences appear in the Port and Protocol panels.

...

Caption
0Figure
1Port

...

and Protocol

...

Image Added

...

Configuration Field

PRI (T1)

BRI

Fractional

(tick)

(error)

TEI Assignment

(error)

(tick)

TEI

(error)

(tick)

Creating an ISDN Signaling Group

To create an ISDN Signaling Group:

  1. From the Create Signaling Group drop down box at the top of the Signaling Group Table, select ISDN Signaling Group.

    Panel
    borderStylenone

    Caption
    0Figure
    1Create ISDN Signaling Group

    Image Modified

     

    Anchor
    properties
    properties

...

Port and Protocol - Field Definitions

...

Panel
titleJump to Field Definition
Table of Contents
maxLevel4
minLevel4

Port Name

Panel
bgColor#FAFAFA
borderStylenone

Specifies the physical T1/E1 port used for this Signaling Group.

...

Panel
bgColor#FAFAFA
borderStylenone

Specifies whether or not the port is fractional. If selected, you must add a list of channels

Channel list Selection

...

bgColor#FAFAFA
borderStylenone

Specifies to which channels the Signaling Group is applied if the port is fractional

...

.

Caption
0Figure
1Channel List Selection

...

Image Added

 

Switch Variant

Panel
bgColor#FAFAFA
borderStylenone

Specifies the ISDN variant for this signaling group.

...

Panel
bgColor#FAFAFA
borderStylenone

Specifies when to generate local ring back

  • Auto on Alert: Depends if inband audio is available when processing alert
  • Auto on Alert/Progress: Depends if inband audio is available when processing Alert or Progress
  • Always on Alert: Always generate inband ringback when processing Alert
  • Always on Alert/Progress: Always generate inband ringback when processing Alert or Progress
  • Never: Never generate inband ringback when processing Alert or Progress

Service Msg Capability

Panel
bgColor#FAFAFA
borderStylenone

Specifies if service messaging is used on the signaling group. Only valid for ATT 4ESS, ATT 5ESS, NI2 and INS Sonus 1500 Switch Variants.

...

Panel
bgColor#FAFAFA
borderStylenone

Specifies the TEI to assign for BRI when set to user side. 0 through 63 are absolute values to assign. If signaling group is PRI or network side BRI this parameter is not used. This field is available only when the TEI Assignment Type is set to Static.

Note
  The value of 0 for Static TEI is valid only for NTT. Other BRI specifications allow a value of 0 through 63 for Static TEI.

 

Send Calling Name

Panel
bgColor#FAFAFA
borderStylenone

Specifies whether or not the Q.931 SETUP message is sent to the far-end should include the DISPLAY Information Element (IE).
Available only when ISDN Side is set to User and the Switch Variant is set to NI2 or Euro-ISDN.

If this option is enabled, the DISPLAY IE is populated for NI2 or Euro-ISDN switch types, otherwise the DISPLAY IE is not populated for these switch types.

In general, the DISPLAY IE is populated according to ISDN communication standards. The NI2 and Euro-ISDN specifications state that the DISPLAY IE should not be populated. This option allows you to override that configuration for your environment.

Add

...

PI to Setup

Panel
bgColor#FAFAFA
borderStylenone

This configuration option enables the ISDN Signaling Group to add/configure a Progress IE to the outbound SETUP message if it is not present. Options are as follows:

  • None (a Progress IE is not added if there is none present, and not modified if present)
  • Not end to end ISDN (call is not end to end ISDN)
  • Destination not ISDN (destination address is not ISDN)
  • Origination not ISDN (originiation address is not ISDN)
  • Return to ISDN (call has returned to the ISDN)
  • Interworking Encountered (interworking has been encountered)
  • Inband Information (in-band information or appropriate pattern now available)
  • Delay Encountered (delay in response at destination interface)

Default entry: None.

Early Media for PI: 2(Dest not ISDN)

Panel
bgColor#FAFAFA
borderStylenone

Defines how PROCEEDING/PROGRESS/ALERT messages are treated for Early Media. Valid options:

Enabled. The PI:2 (Destination not ISDN) value would be treated as if early media was received.in PROCEEDING/PROGRESS/ALERT messages.

Disabled. The PI:2 (Destination not ISDN) value would be treated as if there were no early media received in PROCEEDING/PROGRESS/ALERT messages.

Include Channel Interface

...

identifier

Panel
bgColor#FAFAFA
borderStylenone

Specifies whether to include the Interface Identifier in the Channel Identification Information Element.

...

Panel
bgColor#FAFAFA
borderStylenone

Specifies whether or not to include the Network Facility Extension and Interpretation APDU in ASN.1 for QSIG. All QSIG specific ISDN Signaling groups must be configured the same system-wide for this field.

 

Channels and Routing - Field Definitions

...

Panel
bgColor#FAFAFA
borderStylenone

In the event of a "No Channel/Circuit available" release cause code, the specified cause code will be sent to the relevant protocol module. For more information see the list of Cause Codes.

NOTE: This attribute relates only to Inbound calls on the Signaling Group where applied.

 

Play Inband Message post-disconnect

...

Timer

Timer Definition

T301

Started when an ISDN call enters the alerting state (i.e.receive an ALERT message) and if it expires clears the call. Prevents the call from ringing forever.

T302

Specifies the time between digits in overlapped dialing.  If it expires it is assumed all digits have been received.

T303

Specifies the time after sending a ISDN SETUP message to wait for a response. First expiration will resend the SETUP and second expiration will fail the call.

T305

Specifies the time to wait after sending an ISDN DISCONNECT message to wait for the RELEASE message response. If it expires we then send an ISDN RELEASE message.

T308

Specifies the time to wait after sending an ISDN RELEASE message to wait for the RELEASE COMPLETE message response. First expiration will resend the RELEASE message and second expiration will send a RELEASE COMPLETE message.

T309

Specifies the time to wait after the D channel goes down for B channels with calls in the active state to wait for the D channel to come back up. If it expires and the D channel has not come back up the call on the B channel is cleared.

T310

Specifies the time to wait after receiving a CALL PROCEEDING message to wait for some form of call progress, i.e. a PROGRESS, ALERT or CONNECT message. If it expires the call is cleared.

T313

Specifies the time for user side ISDN to wait after sending a CONNECT message to wait for the CONNECT ACKNOWLEDGE message. If it expires then the call is cleared.

T314

Specifies the time to wait between SEGMENT messages for segmented message support in QSIG. If it expires all previously received SEGMENT messages are discarded and ignored.

T316

Specifies the time to wait after sending a RESTART message to wait for the RESTART ACKNOWLEDGE. First expiration will resend the RESTART message and second expiration will put the channel in local maintenance state for protocols that support service messaging. For protocols that don't support service messaging channel will be returned to the idle state.

T322

Specifies the time to wait after sending a STATUS ENQUIRY message to get the STATUS message response. First expiration will resent the STATUS ENQUIRY message and second expiration will clear an active call. Only started if T309 doesn't expire and the D channel comes back up before T309 expires on B channels with active calls.

T3M1(T323)

Specifies the time to wait after sending a SERVICE message to get the SERVICE ACKNOWLEDGE response. If it expires the SERVICE message will be resent. For NI-2 this is a maximum of 3 attempts before leaving the B channel in the state it was before and not changing its state.

Pagebreak