Page History
add_docset_workflowworkflow_for_techpubs | ||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Panel | ||||
---|---|---|---|---|
In this section:
|
...
Configuring the ASM Network Settings with DHCPv4 Disabled
Info |
---|
ASM configuration is also completed under Tasks > Lync™ Survivable Branch Appliance > Setup SBA> ASM Config. |
If you wish to statically define the IP address of the ASM, follow these instructions:
...
Panel | ||||
---|---|---|---|---|
| ||||
Specifies the IP address mode that is assigned for the interface used by the ASM. Choices are IPv4 or IPv4 and IPv6. Depending on the mode selected, specific configuration fields are displayed; these are noted where applicable. When the IPv4 and IPv6 option is selected, IPv4 and IPv6 configuration is available.
|
DHCPv4 Enabled
Panel | ||||
---|---|---|---|---|
| ||||
Specifies whether DHCPv4 is enabled on the interface through which the ASM communicates. When this field is set to No, the IP configuration fields are displayed. |
...
Panel | ||||
---|---|---|---|---|
| ||||
Specifies the primary IPv6 address for the port through which the ASM communicates. This entry is in a colon-hex notation (i.e., 2001:db8:10::100). Note: In order to configure IPv6 on the ASM, the ASM must be running Windows Server 2012R22019. Field is displayed only when DHCPv4 Enabled for Network Adapter 1 is set to No. |
...
Panel | ||||
---|---|---|---|---|
| ||||
Specifies the IP address mode that is assigned for the interface used by the ASM. Choices are IPv4, IPv6 or IPv4 and IPv6. Depending on the mode selected, specific configuration fields are displayed; these are noted where applicable. When the IPv4 and IPv6 option is selected, both IPv4 and IPv6 configuration is available.
|
DHCP Enabled
Panel | ||||
---|---|---|---|---|
| ||||
Specifies whether DHCP is enabled on the interface through which the ASM communicates. When this field is set to No, the IP configuration fields are displayed. |
...
Panel | ||||
---|---|---|---|---|
| ||||
Specifies the primary IPv6 address for the port through which the ASM communicates. This entry is in a colon-hex notation (i.e., 2001:db8:10::100). Note: In order to configure IPv6 on the ASM, the ASM must be running Windows Server 2012R22019. Field is displayed only when DHCPv4 Enabled for Network Adapter 2 is set to No and IP addressing Mode is set to IPv6 or IPv4 and IPv6. |
...
Note | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
The IP address assigned by the DHCP server must be on the same subnet as
If there is no DHCP server answering requests, a 169 addressing scheme is assigned to the ASM after a timeout period. | ||||||||||||||||
Info | ||||||||||||||||
ASM configuration is also completed under Tasks > Lync™ Survivable Branch Appliance > Setup SBA> ASM Config. |
Enable DHCP:
- In the WebUI, click the Settings tab.
In the left navigation pane, go to Application Solution Module > ASM Configuration. For field definitions, see ASM Configuration - Field Definitions.
The example below shows DHCP disabled for IPv4 on Network Adapter 1 and enabled for IPv4 on Network Adapter 2.
Network Adapter 1 ASM Configuration - DHCP EnabledFrom DHCPv4 Enabled, select Yes. Depending on the IP Addressing mode selected, IPv4 and/or IPv6 options are displayed. See below:
DHCPv4 Enabled, Configuration Options
Network Adapter 1DHCPv4 Enabled IP Addressing Mode Configuration Options Available Yes IPv4 None Yes IPv4 and IPv6 IPv6 Configuration
Network Adapter 2DHCPv4 Enabled IP Addressing Mode Configuration Options Available Yes IPv6 IPv6 Configuration Yes IPv4 None Yes IPv4 and IPv6 IPv6 Configuration - Update configuration (see Network Adapter 1 Configuration - Field Definitions and Network Adapter 2 Configuration - Field Definitions.
- Click Apply.
...