Page History

...

1. In the WebUI, click the Settings tab.

2. In the left navigation pane, go to Node Interfaces > Ports.

   Panel
   borderStyle none
   Caption 0 Figure 1 Port Table View Image Modified

FXS Long Loop

By using the FXS long loop feature, the maximum length of the local loop supported by SBC1K/2K FXS line cards can be extended to 3000 meter. To accomplish this, you must configure the Long Loop on per FXS line card. The FXS port on this line card supports devices connected using up to 3000 meters long cables.

...

1. In the WebUI, go to Settings > Node Interfaces > Ports.
   The Port Table View window appears.

   Panel
   borderStyle none
   Caption 0 Figure 1 Port Table View 3 Port Table View Image Modified

2. Select SET FXS Local Loop Type option on the top of the window. The following window appears.

   window

   Panel
   borderStyle none
   Caption 0 Figure 1 Local Loop Type	Window 3 Local Loop Type window Image Modified

3. Select the FXS long loop for FXS line card in Slot 1 and Slot 3.

   Note
   You can select FXS long loop for FXS line card in Slot 1, Slot 3, and Slot 5, based on your requirement. There are two available options: Long Loop and Standard.

4. Click OK.

   A confirmation window appears. You are prompted to confirm the changes.

   Panel
   borderStyle none
   Caption 0 Figure 1 Confirmation Window 3 Confirmation Window Image Modified

5. Click OK.

   Note
   If you want to discard the changes, click Cancel.

   Once this selection is submitted, all the changes are applied to the FXS Line card in each slot. The  The following Port Table View window shows port type for each slot. The Port Type is changed form FXS to FXS Long Loop in slot 1 and slot 3.
   Also, the FXS line card in slot 2 and slot 4 are disabled and are unavailable to handle calls. This infers that the upper FXS cards in the system are disabled if long loop is applied. 

   Panel
   borderStyle none
   Caption 0 Figure 1 Port Table View After Applying FXS Long Loop 3 Port Table View After Applying FXS Long Loop Image Modified

Viewing Monitor Tab

The following image shows that the FXS Module 2 and FXS Module 4 are not displayed under Sonus SBC 1000 Main Board.

Viewing Overview Tab

The following image shows that Telco Module 2 and Telco Module 4 are disabled.

Viewing Ports Inventory

The following image shows that Telco Module 2 and Telco Module 4 are disabled.

Configuring FXS Long Loop on SBC 2000

1. In the WebUI, go to Settings > Node Interfaces > Ports.
   The Port Table View window appears.

   Panel
   borderStyle none
   Caption 0 Figure 1 Port Table View 3 Port Table View Image Modified

2. Select SET FXS Local Loop Type option on the top of the window. The following window appears.

   Panel
   borderStyle none
   Caption 0 Figure 1 FXS Long Loop Type 3 FXS Long Loop Type Image Modified

3.  Select the FXS long loop for FXS line card in Slot1 and Slot 2.

4. Click OK.

   A confirmation window appears. You are prompted to confirm the changes

   Panel
   borderStyle none
   Caption 0 Figure 1 Confirmation Window Image Modified

Once this selection is submitted, all the changes are applied to the FXS Line card in each slot. The following Port Table View window shows port type for each slot. You can see that the Port Type is changed to FXS Long Loop.

Viewing Monitor Tab

Viewing Overview Tab

The Port Status panelshows that the Port Type is changed to FXS Long Loop.

Viewing Ports Inventory

The Ports panelshows that the Port Type is changed to FXS Long Loop.

Modifying a Port

To modify a Port:

Identification/Status - Field Definitions

...