Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ccb8089c, userName='null'}
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd0f0958, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cc7d083d, userName='null'}

 

Note
iconfalse
titleNote

An ESXi VMware console is used as an example for this procedure, other consoles may look slightly different.

Info

To assign a virtual NIC to a physical network adaptor, refer to the respective third-party documentation:

KVM Hypervisor: http://www.linux-kvm.org/page/HOWTO

Microsoft Hyper-V: https://technet.microsoft.com/en-us/library/mt169373(v=ws.11).aspx

VMware ESXi: https://www.vmware.com/support/pubs/

Note
iconfalse
titleNote

Access the console by: 

    • Clicking the Console tab, or
    • Clicking the Summary tab, and then clicking the Open Console link. (The 
      Spacevars
      0series3
             must be powered on for this to work).

...

  1. Log in as user netconfig with password as Config!. Change the password when prompted.

    Note
    iconfalse
    titleNote

    Passwords must be at least six characters in length and include uppercase and lowercase characters, and numerals.

     

    Caption
    0Figure
    1Modify Password
    3Modify Password

    Image Modified

    Caption
    0Figure
    1Static or DHCP IP
    3Static or DHCP IP

    Image Added

  2. Choose DHCP or enter a static IP address.

    Code Block
    Would you like to configure a static IP address for Initial Setup on the Admin interface? This is only required if DHCP is unavailable (y/[n]): n

     

    Note
    iconfalse
    titleNote

    Sonus recommends that you first connect the admin port to a network with DHCP server enabled, otherwise you will need to enter a static IP address when prompted for an IP address.  

  3. Enter the interface name to map the interface as shown in the WebUI when prompted by the interface mapping shell script.

     

    Info
    icontitlefalseInfo

    The interface mapping shell script requests that the user provide the interface name to map the interface as shown in the WebUI.

    Use the MAC address (identified previously in the virtual machine editing portion during Installing SBC SWe Lite on your specific platform) in order to correctly map the interface. The interface name and MAC address are required to properly activate the interface and have it appear on the WebUI.

  4. Enter an admin interface name. Example: mgt0.

  5. Enter an Ethernet 1 Media interface name. Example: pkt0.

  6. Enter each subsequent Ethernet Media interface Name, and then apply the changes.

Caption
0Figure
1Saving Interface Mapping
3Saving Interface Mapping

Image Modified

  

Info
iconfalse
If the network mapping and connection are correct, the Admin IP address will display on the console port. If the Admin IP address does not display, check the connections and network mapping.

...

Note
iconfalse
titleNote
If DHCP is used, 
Spacevars
0series3
 will automatically reboot before initial setup.  If  If a static IP address is set, 
Spacevars
0series3
 will automatically reboot after SBC SWe Lite Initial Setup  from the WebUI.
Note
iconfalse
titleNote
If  this If this is the first time interface mapping is being done, the system will automatically reboot. Any future remapping of interfaces will not automatically trigger a reboot, but will inform the user that they need to do so in order for the changes to be placed into affect.

...