Page History

...

1. In the WebUI, click the Settings tab.
   
   
2. In the left navigation pane, go to SIP > SIP Server Tables.
   
   
3. Create a new IP Server Table. Click on the Create () icon.
   The SIP Server Tables page is a table of SIP Server Tables.
   
   

4. Configure the new SIP Server Table as shown in the illustration below.

   Panel
   borderStyle none
   Caption 0 Figure 1 Create SIP Server Table

    

    

5. In the left navigation pane, go to SIP > SIP Server Tables > (The table you created in the previous step).
   
   
6. Click the Create SIP Server > IP/FQDN.
   
   
7. Enter the IP address of the eUM Server in the Host as shown below.
   
   

8. Click OK.

   Panel
   borderStyle none
   Caption 0 Figure 1 Create SIP Server Entry Image Modified

Transformation Table

1. In the WebUI, click the Settings tab.
   
   
2. In the left navigation pane, go to Transformation.
   
   
3. Click the Create () icon.
   
   

4. Create a new Transformation Table.

   Panel
   borderStyle none
   Caption 0 Figure 1 Create Transformation Table Image Modified

    

    

5. In the left navigation pane, go to Transformation >(the table created in the previous step).
   
   

6. Add an entry as shown below.

   Panel
   borderStyle none
   Caption 0 Figure 1 Add Entry Image Modified

Call Routing Table

1. In the WebUI, click the Settings tab.
   
   
2. In the left navigation pane, go to Call Routing Table.
   
   

3. Create two entries (Calls from ISDN, Calls to ISDN) as shown below.

   Panel
   borderStyle none
   Caption 0 Figure 1 Create

   Two

   two Entries Image Modified

Port Configuration

1. In the WebUI, click the Settings tab.
   
   
2. In the left navigation pane, go to Node Interfaces > Ports.
   
   
3. Click the port that you wish to connect to the physical PRI line.
   
   

4. Fill in the fields as shown below.

   Panel
   borderStyle none
   Caption 0 Figure 1 Port Configuration Image Modified

Signaling Groups

1. In the WebUI, click the Settings tab.
   
   
2. In the left navigation pane, go to Signaling Groups.
   Click Create Signaling Group and select ISDN Signaling Group text at the top of the table.
   
   

3. Fill in the fields as shown below.

   Panel
   borderStyle none
   Caption 0 Figure 1 Create ISDN Signaling Group Image Modified

    

    

1. In the WebUI, click the Settings tab.
   
   
2. In the left navigation pane, go to Signaling Groups.
   
   
3. Click Create Signaling Group and select SIP Signaling Group.
   
   

4. Fill in the fields as shown below.

   Panel
   borderStyle none
   Caption 0 Figure 1 Create SIP Signaling Group Image Modified

    

    

The Signaling Groups should appear like the following after adding the ISDN and SIP Signaling Groups:

Panel
borderStyle none
Caption 0 Figure 1 Signaling Group Table Image Modified

 

Call Routing Table Entries

1. In the WebUI, click the Settings tab.
   
   
2. In the left navigation pane, go to Call Routing Table > (call route entry for ISDN).
   
   

3. Fill in the fields as shown below.

   Panel
   borderStyle none
   Caption 0 Figure 1 Call Route Entry

   For

   for ISDN Image Modified

1. In the WebUI, click the Settings tab.
   
   
2. In the left navigation pane, go to Call Routing Table > (call route entry for SIP)
   
   

3. Fill in the fields as shown below.

   Panel
   borderStyle none
   Caption 0 Figure 1 Call Route Entry

   For

   for SIP Image Modified

System Timing Configuration

1. In the WebUI, click the Settings tab.
   
   
2. In the left navigation pane, go to System > System Timing.
   
   

3. Configure the Clock Source either as System or the Network, depending on your PBX timing settings.
   In this exercise, the Sonus SBC 1000/2000 node is reading the system time from the network therefore the configuration is done as shown below:
   For more information about system timing see, Configuring the System Clock Source.

   Panel
   borderStyle none
   Caption 0 Figure 1 System Timing Configuration Image Modified

Exchange 20xx UM Server Configuration Steps

...

• Logon to Exchange / UM Server PC
• Launch Exchange Management Console
• Create a New Dial Plan using the following information:

Subscriber Access Number

Panel
borderStyle none
Caption 0 Figure 1 Subscriber Access Number Image Modified

 

Dialing Rule Group for 4 digit dialing used in this example:

Panel
borderStyle none
Caption 0 Figure 1 Dialing Rule Group Image Modified

 

Dialing Restriction

 

Panel
borderStyle none
Caption 0 Figure 1 Dialing Restriction Image Modified

 

UM Mailbox Policy

 

Panel
borderStyle none
Caption 0 Figure 1 UM Mailbox Policy Image Modified

 

UM IP Gateway

 

Panel
borderStyle none
Caption 0 Figure 1 UM IP Gateway Image Modified

 

UM Auto Attendants

Panel
borderStyle none
Caption 0 Figure 1 UM Auto Attendants Image Modified

Panel
borderStyle none
Caption 0 Figure 1 Dialing Restriction Image Modified

 

Associating Dial Plan to UM Server

• Logon to Exchange / UM Server PC.
• Launch Exchange Management Console.

• Associate the relevant dial plan with the UM Server as shown below:

  Panel
  borderStyle none
  Caption 0 Figure 1 Associate Dial Plan Image Modified

SBC Edge Signaling Group Status Verification

After having completed both 

Spacevars
0 product

and Exchange 20xx Unified Messaging Server configuration steps, using the monitor view, ensure both PRI and SIP ports are up and in idle as shown below:

Panel
borderStyle none
Caption 0 Figure 1 Monitor View Image Modified

 

Common Use Case

In a PBX – 

Spacevars
0 product

– eUM Server scenario the following configuration steps allow PBX users to have UM voice mail boxes:

1. On the PBX, a user must be configured with a diversion number as the Subscriber Access Number (i.e: 6255).
   This number is configured in the Exchange Management Console >> Organization Configuration >> Unified Messaging >> UM Dial Plan >> Subscriber Access tab.
   
   

2. On the eUM, the relevant user entry must be enabled for Unified Messaging as shown below:

   Panel
   borderStyle none
   Caption 0 Figure 1 eUM Image Modified

3. When a PBX user-1 receives a call (i.e., from PBX user-2) and does not answer, the call is diverted by the PBX to the diversion number (6225). The call arrives at the

   Spacevars
   0 product

   , and the 

   Spacevars
   0 product

   sends an INVITE to the UM Server. Once the call reaches the UM Server, the Calling Party can leave a message in PBX user-1's voice mail box.
   
   
4. In addition, PBX user(s) can call a Subscriber Access (SA) Number (6255) and an Auto Attendant (AA) Number (6256) via 4 digit dialing in above setup to navigate UM prompts via DTMF or voice commands

...