...
Caption |
---|
0 | Figure |
---|
1 | Creating a SIP Registration Table |
---|
|
Image RemovedImage Added |
Tenor Call Routing Table
Create a Call Routing Table for Tenor, as shown below to route a fax call from Tenor to PSTN through the SBC Edge.
Note |
---|
If the call format doesn't does not need to be transformed (Ex. 1001 to +133123451001), use any “Passthrough untouched” transformation table. |
Caption |
---|
0 | Figure |
---|
1 | Creating a Call Routing Table for Tenor |
---|
|
Image RemovedImage Added |
Tenor Signaling Group
- Create the Tenor SIP Signaling Group which allows the SBC 1000/2000 to send and receive SIP calls to/from the Tenor with the following parameters (created previously).
- Verify that the values in the Port and Protocol fields in the Listen Ports panel configured for the Tenor are the same when configuring the SBC1000/2000.
Tenor Transformation Table
...
Caption |
---|
0 | Figure |
---|
1 | Creating a Dedicated Tenor Transformation Table |
---|
|
Image RemovedImage Added |
PSTN Incoming Call Routing Table entry table adaptation
...
Caption |
---|
0 | Figure |
---|
1 | Call Routing Entry: From PSTN to Tenor |
---|
|
Image RemovedImage Added |
Note |
---|
This call routing entry needs to be re-ordered at the top of the Call Routing Table “From PSTN to Tenor” if there are multiple entries, if not, it will never be evaluated and the calls to 1xxx will never go to the Tenor. |
...
Select the Advanced Explore tab to access all parameters.
Image Removed Caption |
---|
|
Image Added |
- Select Confirm/OK after making changes.
- Select the "red star button" to apply changes to the Tenor:
Note |
---|
Each time a screenshot has a non default parameter, it displays or is highlighted in purple as shown below. |
Caption |
---|
0 | Figure |
---|
1 | IP Routing Group-default |
---|
|
Image RemovedImage Added |
Dial Plan
- Adapt the Dial Plan to the one necessary for the appropriate country.
- Select a generic Dial Plan and remove the other prefixes.
Caption |
---|
|
Image RemovedImage Added |
SIP Signaling Group
...
Caption |
---|
0 | Figure |
---|
1 | SIP Signaling Group 1 of 3 |
---|
|
Image RemovedImage Added |
On the Advanced tab, make sure the protocol matches the one configured previously in the Tenor Signaling Group:
Caption |
---|
0 | Figure |
---|
1 | SIP Signaling Group 2 of 3 |
---|
|
Image RemovedImage Added |
On the User Agent tab, create as many User Agents as analog ports to register as SIP UA:
Caption |
---|
0 | Figure |
---|
1 | SIP Signaling Group 3 of 3 |
---|
|
Image RemovedImage Added |
Caption |
---|
0 | Figure |
---|
1 | Edit User Agent 1 of 2 |
---|
|
Image RemovedImage Added |
Caption |
---|
0 | Figure |
---|
1 | Edit User Agent 2 of 2 |
---|
|
Image RemovedImage Added |
DN Channel Map
...
Caption |
---|
0 | Figure |
---|
1 | Edit DN Channel Map 1 of 2 |
---|
|
Image RemovedImage Added |
Caption |
---|
0 | Figure |
---|
1 | Edit DN Channel Map 2 of 2 |
---|
|
Image RemovedImage Added |
Codec
Enter at least one G.711A codec:
Caption |
---|
|
Image RemovedImage Added |
Codec Profile
Verify the default codec profile is configured with the previously created codec:
Caption |
---|
0 | Figure |
---|
1 | Codec Profile-default |
---|
|
Image RemovedImage Added |
IP Routing Group
...
Caption |
---|
0 | Figure |
---|
1 | IP Routing Group-default |
---|
|
Image RemovedImage Added |
Gateway - Routing Table Mode
...
Caption |
---|
0 | Figure |
---|
1 | Number Table-Tenor-SBC 1 of 2 |
---|
|
Image RemovedImage Added |
Note |
---|
When the Routing Table mode is activated, the following menu displays to configure matching incoming/outgoing patterns/rules. Asterisks (*) in the Incoming Pattern and Outgoing Pattern configures the Tenor to route all calls. |
Caption |
---|
0 | Figure |
---|
1 | Number Table-SBC-Tenor |
---|
|
Image RemovedImage Added |
Create or rename a Number table by clicking the Number Tables drop-down list or any item on the list.
Caption |
---|
0 | Figure |
---|
1 | Number Table-Tenor-SBC 2 of 2 |
---|
|
Image RemovedImage Added |
Caption |
---|
0 | Figure |
---|
1 | Number Table - New |
---|
|
Image RemovedImage Added |
Create entries in the Routing Table to route calls from Tenor to SBC 1000 (LCRG-phone to UA-101 below) and reverse (ip to LCRG-phone below):
Caption |
---|
|
Image RemovedImage Added |
Caption |
---|
0 | Figure |
---|
1 | Edit Routing Table Entry 1 of 2 |
---|
|
Image RemovedImage Added |
Caption |
---|
0 | Figure |
---|
1 | Edit Routing Table Entry 2 of 2 |
---|
|
Image RemovedImage Added |
These tables only look for and can adapt the called number in the above example, but you can also adapt the calling number.
...