Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH2UserResourceIdentifier{userKey=8a00a0c85f4199b1015f7edf811e000e, userName='null'}
AUTH1UserResourceIdentifier{userKey=8a00a0c8613a801e016167f8a31a002b, userName='null'}
REV5UserResourceIdentifier{userKey=8a00a0c85f4199b1015f7ea6e836000d, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a0c85f4199b1015f7ea6e836000d, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a0c866dc3dee01670fed916200308a00a02355cd1c2f0155cd26c8a10148, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a0c866dc3dee01670fed916200308a00a02355cd1c2f0155cd26cb1f0553, userName='null'}

Overview

Use this procedure to restore from backup the configuration settings of your Edge 8000 device. The sys-tools config restore command restores the system to a previous backup configuration. The command also restores the settings of all the components that were active in the device, including 

  • Analog Manager -  SIP User Agent, SIP Gateway, and PRI Settings (8300 only)
  • Routing - All configuration settings

  • SBC SWe Edge - This is a pre-installed KVM virtual machine (VM), so the complete VM is saved in this process, including the running configuration.


  • User Management - Users and Passwords

Multiexcerpt include
MultiExcerptNameThis procedure applies to all E8k devices
PageWithExcerpt_Operations_excerpts

Info
titleNote

You can also save and download the SBC SWe Edge running configuration separately using the SWe Edge GUI interface.


Info
titleAttention

For a full recovery of all the system software of the Edge 8000 device, including the operating system software, refer to Performing Disaster Recovery.

Multiexcerpt include
MultiExcerptNameWarning - interruption of service
PageWithExcerpt_Operations_excerpts

Prerequisites

  • Access to the backup file . (The backup command saves the backup file in directory /E8000/backup_config/. Your system administrator knows the location of the off-site backup directory.)created from running the prior backup procedure.
  • System Administrator login access to the
    Spacevars
    0product
    CLI, SSH, or Console port.
  • Physical access to the GE 7 port of the
    Spacevars
    0product
    device.

Start

  1. Connect the management computer to port GE 7 at the front of the
    Spacevars
    0product
    device.
    The computer will receive a DHCP IPv4 Address on the Edge 8000's management subnet, 192.168.122.0/24.
    If the system's management network is reachable from the remote management computer, then SSH directly to the management IPv4 Address.
  2. Open a secure shell (ssh) session to the system's management IPv4 address. The default IP address is 192.168.122.1.
  3. Log in to the
    Spacevars
    0product
    CLI as System Administrator (sysadm) and enter the password.
  4. Change permission to root user by enteringsudo -i. Then enter the sysadm user password.

  5. Execute the system tools (sys-tools) command to restore the configuration settings from backup.
    Syntax:
    sys-tools config restore <backup_file_name>
     

    Code Block
    titleExample
    # sys-tools config restore 05102023v1_2023-05-10-11.01.23.tgz
Config restore will interrupt voice services for approximately 60 seconds.
Current calls will be disconnected, Continue (yes/no)?
yes
Domain 'SBCSWeEdge' destroyed

umount disk
disconnect /dev/nbd5
/dev/nbd5 disconnected
virsh start SBCSWeEdge
Domain 'SBCSWeEdge' started
...
virsh start SBCSWeEdge  ====> Success.
systemctl stop evagent.service  ====> Success.
systemctl stop emtunnel.service  ====> Success.
[root@e8000 /]#


  6. Exit the CLI session and remove the physical connection from the GE 7 port.