Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Panel

In this section:

Table of Contents
maxLevel3
minLevel2


Include Page
_SBC 5100 5110 5200 5210 Unsupported
_SBC 5100 5110 5200 5210 Unsupported

SBC 5000 Series Hardware Platforms

Ribbon

Spacevars
0series
is available in four different platforms. The 
Spacevars
0series
platforms are similar as they use the same types of components, but different models provide different hardware and capacity capabilities. All SBC 5000 hardware platforms support the Ribbon SBC application software.

  • SBC 5100 Platform—Small to medium session count deployments. The capacities make this product particularly well suited for medium enterprises and small to medium service providers.
  • SBC 5110 Platform—This is a modular form SBC that targets small and medium count deployments. This SBC model allows you to field install digital signal processor (DSP) cards as their network expands.
  • SBC 5200 Platform—Medium to large session count deployments. The capacities make this product particularly well suited for large enterprises and medium to large service providers.
  • SBC 5210 Platform—This is a modular form SBC that targets medium to large session count deployments. This SBC model allows you to field install digital signal processor (DSP) cards as their network expands.
  • SBC 5400 Platform—The
    Spacevars
    0model5
     hardware platform comes equipped with four media ports and is available in three models based on the media port configuration. You must purchase the appropriate model based on their interface and capacity requirements. The media ports are enabled on the chassis depending upon the network interface license installed. For SBC 5400 Hardware information, refer to Installing SBC 5000 Series Hardware.

Hardware Specifications

SBC 5100

Caption
0Figure
1SBC 5100 Front View


Caption
0Figure
1SBC 5100 Rear View


Caption
0Table
15100 Specifications


Front PanelRear PanelExpansion StorageMemory Power Option
  • Status Indicators Front Panel LEDs
  • Single USB V2.0 interface
  • Two 10/100 Management Ports
  • Two Media Ports
  • Two High Availability Ports
  • Single Field Service port with RJ45 connector
  • Locator LED
  • Alarm port with DB15 connector
  • Single serial craft DB9 port
DSP expansion card
(SPS100 / SPS100DB) 

80 GB (minimum), 120 GB, or 128 GB Solid State Disk (SSD)

 


12 GB RAM  AC and DC 




SBC 5110

Caption
0Figure
1SBC 5110 Front View


Caption
0Figure
1SBC 5110 Rear View


Caption
0Table
15110 Specifications


Front PanelRear PanelExpansion (Modular) StorageMemory Power Option
  • Status Indicators Front Panel LEDs
  • Single USB V2.0 interface
  • Two 10/100 Management Ports
  • Two Media Ports
  • Two High Availability Ports
  • Single Field Service port with RJ45 connector
  • Locator LED
  • Alarm port with DB15 connector
  • Single serial craft DB9 port

Up to four DSP 25 cards, or
one DSP 20 card

80 GB (minimum), 120 GB, or 128 GB Solid State Disk (SSD) 24 GB RAM  AC and DC 




SBC 5200

Caption
0Figure
1SBC 5200 Front View
3SBC 5200 Front View


Caption
0Figure
1SBC 5200 Rear View


Caption
0Table
15200 Specifications


Front PanelRear PanelExpansion StorageMemory Power Option
  • Status Indicators Front Panel LEDs
  • Single USB V2.0 interface
  • Two 10/100 Management Ports
  • Four Media Ports
  • Two High Availability Ports
  • Single Field Service port with RJ45 connector
  • Locator LED
  • Alarm port with DB15 connector
  • Single serial craft DB9 port

DSP expansion card
(SPS100 / SPS100DB)

256 GB (minimum) or 300 GB Solid State Disk (SSD)

24 GB RAM AC and DC 




SBC 5210

Caption
0Figure
1SBC 5210 Front View


Caption
0Figure
1SBC 5210 Rear View


Caption
0Table
15210 Specifications


Front PanelRear PanelExpansion (Modular) StorageMemory Power Option
  • Status Indicators Front Panel LEDs
  • Single USB V2.0 interface
  • Two 10/100 Management Ports
  • Four Media Ports
  • Two High Availability Ports
  • Single Field Service port with RJ45 connector
  • Locator LED
  • Alarm port with DB15 connector
  • Single serial craft DB9 port

Up to four DSP 25 cards,
or one DSP 20 card

256 GB (minimum)  or 300 GB Solid State Disk (SSD)

24 GB RAM  AC and DC 



Note

Note:

  • The HA mode can support mix SSD capacity.
  • The show table system hardDiskStatus may show different SSD sizes.

  • The shipped SSD size is determined based on availability.

Chassis

The Ribbon 

Spacevars
0series
 2U rack-mounted chassis can be front or center mounted in standard 19” or 23" wide racks.

The SBC 5100/5200 chassis accommodates following modules:

  • Motherboard
  • Optional DSP base card
  • Up to two optional DSP expansion cards (SPS100 / SPS100DB)

The SBC 5110/5210 chassis accommodates following modules:

  • Motherboard
  • Up to four DSP 25 modules or one DSP 20 modules
Note

The chassis must be installed in adherence with the environmental specifications and power source requirements listed in Post Installation Checklist.

Front Panel

The 

Spacevars
0series
chassis includes a front panel on which the various input/output ports and LEDs are located.

 The SBC 5000 Series Hardware Platform Specifications#Front Front Bezel and LEDs of SBC 5100/5110 Series figure shows the front panel LEDs with and without Bezel mounted on the front panel of SBC 5100/5110.

Anchor
FP-5100
FP-5100

Caption
0Figure
1Front Bezel and LEDs of SBC 5100/5110 Series
3Front Bezel and LEDs of SBC 5100/5110 Series

The SBC 5000 Series Hardware Platform Specifications#Front Front Bezel and LEDs of SBC 5200/5210 Series figure shows the front panel LEDs with and without Bezel mounted on the front panel of SBC 5200/5210.

Anchor
FP-5200
FP-5200

Caption
0Figure
1Front Bezel and LEDs of SBC 5200/5210 Series
3Front Bezel and LEDs of SBC 5200/5210 Series

The SBC 5000 Series Hardware Platform Specifications#Front Front panel LEDs Description table lists the front panel LEDs on the

Spacevars
0series
. The default state of all LEDs are during a reset.

Caption
0Table
1Front panel LEDs Description
3Front panel LEDs Description


Illustration

LED

Color

Description

1

Power

Amber/Green

Power status indicator of all voltages generated on the module:

  • Green = All Power on
  • Amber = BMC Power on
  • Off = All Power is Off
2

Status

Amber/Green

Module Status indicator

  • Green = Module is Healthy

  • Amber = Module is Unhealthy

3ActiveAmber/Green

Module Redundancy State Indicator:

  • Green = Module Active and Protected
  • Green Blinking = Module Active and not protected
  • Off = Module is in standby mode

  • Amber = Module is Core Dumping

4

Alarm

Amber/Red

Module Critical/Major Failure Indicator:

  • Red = Critical Alarm
  • Amber = Major Alarm

  • Off = No Alarm Conditions

5

Locator

WhiteModule identifier indicator
6

Fan

Green

Fan module indicator:

  • Green = Module is Healthy
  • Off = Module is not working


Network Ports and Connection

The 

Spacevars
0series
chassis comprises the following external input and output ports:

  • Alarm contacts are provided on the outside of the chassis via a single shielded male DB15 connector.
  • A standard USB connector on the front of the chassis.
  • Front and rear jacks for standard ESD straps.
  • Cable management.
Note

The SBC 5000 system supports USB 2.0.

Rear Panel

The following figures list the rear panel LEDs on the

Spacevars
0series
. The default state of all LEDs is during a reset. The rear panel layout and LEDs are as depicted in the SBC 5000 Series Hardware Platform Specifications#Rear Rear Panel LEDs for SBC 5200 Series figure:

Caption
0Figure
1Rear Panel LEDs for SBC 5200 Series


Caption
0Figure
1Rear Panel LEDs for SBC 5210 Series


Caption
0Figure
1Rear Panel LEDs for SBC 5100 Series


Caption
0Figure
1Rear Panel LEDs for SBC 5110 Series

The SBC 5000 Series Hardware Platform Specifications#Rear Rear Panel Description table lists the Ethernet port LEDs. Each of the Management ports, Media ports, HA ports, and FSP port support the following LEDs.

Caption
0Table
1Rear Panel Description
3Rear Panel Description


Component

Cable Requirement

Description

Alarm Port

Customer supplied cable

Alarm contact via a single shielded male DB15 connector. A single alarm port is present in SBC 5100 platform.
This software release does not support the Alarm Port.

Management Ports

CAT5e cable

Two 10/100 Copper Ethernet Ports which process Management traffic and perform protocol termination.

Locator

 

Module identifier indicator

Media Ports

Single mode or Multi mode fiber Copper CAT5e cable

Two copper SFP or fiber SFP ports for media and signaling traffic.

High Availability Ports

Single mode or Multi mode fiberCopper CAT5e cable (NON-CROSSOVER TYPE ONLY)

Two copper SFP or fiber SFP ports for redundancy synchronization traffic. The platform supports box level redundancy via communication paths provided by the external HA Ethernet ports.

Serial Port

Male DB9 connector

An RS-232 port used by BMC and control plane. The serial port uses a DB9 connector accessible from the rear panel.

Field Service Port

Copper CAT5e cable

A single Field Service Port.

Power Input

 


Power Supply. The following are the descriptions of the power supply LED functions:

  • Off: No power input to the supply.
  • Amber: Power supply fault.
  • Blinking Amber: Main system power output fault.
  • Blinking Green: Standby power to BMC is ON but main system power is not enabled.
  • Solid Green: Both standby power to BMC and main system power are ON and OK.



Warning

Ribbon-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.


Note

CAT6 cabling may be required in environments where there is unusually high Electro-Magnetic interference (EMI) from power lines, manufacturing equipment, or certain types of lighting.


Caption
0Table
1Ethernet Port LEDs Description
3Ethernet Port LEDs Description


Illustration

Port Type

Color

Description

1

Mgmt0 and Mgmt1

Green

Checks if the link and activity is present.

  • Green = Link
  • Flashing = Activity

2

Media ports 0 and 1

Green

Checks if the link and activity is present.

  • Green = Link
  • Flashing = Activity

3

HA ports 0 and 1

Green

Checks if the link and activity is present.

  • Green = Link
  • Flashing = Activity

4

Field Service Port

Green

Checks if the link and activity is present.

  • Green = Link
  • Flashing = Activity



Pagebreak