Page History

Using the Easy Config wizard to configure the

NTT DOCOM Officelink, SoftBank ConnecTalk, SoftBank White Office, and Telstra Enterprise SIP Connect are supported in SBC Edge 1000-2000 only.

Make sure the

Type a short description for the SIP Trunk ↔ IP PBX setup.

Click the country from which the SIP Trunk ↔ IP PBX originates.

The E911 Elin number from the CompanyName field configured in Lync location services is used as the authoritative Callback Number for outgoing E911 calls, and is always the preferred configuration. Specifically, the Elin number takes precedence over any Callback Number configuration in the Lync setup. For more information, refer to Creating and Modifying Entries to Transformation Tables.

Defines the Emergency Services for outgoing numbers. For the purpose of this illustration above, Emergency Services is not selected. Field definitions are defined below.

Options:

• ELIN Identifier
• E911/E112
• None

Specifies the Callback Number in string format. This field displays only when you select the ELIN Identifier or E911/E112 of Emergency Services.

Specifies the second Callback Number in string format. This field displays only when you select the ELIN Identifier or E911/E112 fields of Emergency Services.

Defines the Public Safety Answering Point Number. Specify a valid entry of 1 - 127 characters.

Specifies the type of SIP trunk used for connection to the IP PBX. Valid options include the following SIP trunk types:

• ATT SIP Trunk
• KDDI SIP Trunk
  
• NTT DOCOMO Officelink
• Other SIP Trunk
• SoftBank ConnecTalk
• SoftBank White Office
  
• Telstra Enterprise SIP Connect
• Verizon SIP Trunk
  
  

The SIP Trunk selected determines the field options displayed in Step 2.

Valid options:

• Cisco CUCM
• Other IP PBX
• Avaya SM/CM

Type the FQDN or IP address for the Session Border Controller the Remote Peer service provider.

Choose the IP protocol to use for sending and receiving SIP messages between SBC and the Border Element Server. Valid entries are UDP and TCP.

The pre-defined SIP Server Port number used for sending and receiving SIP messages between SBC and the Border Element Server.

Enables or disables the secondary Session Border Controller secondary Remote Peer service provider configured. 

Specifies the Secondary Border Element Service provider. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Border Element Server is Enabled.

Specifies the protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP. This field displays only when Use Secondary Border Element Server is Enabled.

Specifies the Port Number used for sending and receiving messages between SBC and the Secondary Border Element server. This field displays only when Use Secondary Border Element Server is Enabled.

Specifies the Port Number used for sending and receiving messages between SBC and the Secondary Border Element server. This field displays only when Use Secondary Border Element Server is Enabled.

Enables or disables support for the AT&T Simultaneous Ring service. Select Yes to enable or No to disable the service.

Enables/disables the AT&T Toll Free option. Valid options are: Enabled or Disabled.

The Toll Free Access Number tro use when the AT&T IP Toll Free option is enabled.

Host IP or FQDN.

The Protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled.

The IP PBX port number used for sending and receiving SIP messages.

Enable or Disable use of a secondary server.

The host IP address or FQDN of the primary SIP server.

The host IP address or FQDN of the secondary SIP server.

The method to connect networks. This field has the following options: Routerless and Router.

The user-specified IP address for SIP signaling messages.

The ID that authenticates with the router at the gateway of the network.

The password that authenticates with the router at the gateway of the network.

Re-enter the password for the router that serves as the network gateway.

The IP or FQDN of the SIP Profile and Contact Registrant Table.

This field automatically generates using the Gateway ID at the From/To Header Host.

The FQDN or IP Address of the host.

The protocol that communicates with the Secondary Border Element Server. This field has the following options: UDP and TCP.

The pre-defined IP PBX port number that sends and receives SIP messages. The default value is 5060.

Enables or disables the use of a secondary server. This field has the following options:

• Disabled
• Enabled

The FQDN or IP Address of the secondary server host. This field appears only if you enable Use Secondary Server.

The protocol that communicates with the Secondary Border Element Server. This field has the following options: UDP and TCP. This field appears only if you enable Use Secondary Server.

The pre-defined IP PBX port number that sends and receives SIP messages. The default value is 5060. This field appears only if you enable Use Secondary Server.

Indicates the method to use for connecting networks. Options are: Routerless and Router. Upon selection of Routerless, the Easy Config displays the Signaling/Media Source IP field and the SIP Server field. On selection of Router, the Easy Config displays the SIP Server field only.

The user-specified IP addresses to use for SIP signaling messages. The Signaling/Media Source IP field does not display when the selected value for the WAN Link field is Router.

The host IP address or FQDN for the SIP server.

The ID used for authenticating with the router at the gateway of the network.

The password used for authenticating with the router at the gateway of the network.

Re-entry of the password for the router serving as network gateway.

The public address that points to the domain for users, for use in the Contact Registrant Entry. For example, specify:  GatewayID@SIPServer.

IP address or FQDN for the host.

The Protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled.

The pre-defined IP PBX port number used for sending and receiving SIP messages.

Enables or disables use of a secondary server.

The public interface used for Network Address Translation (NAT).

The state to use in configuring the outbound proxy for the Provider SIP Trunk. Options include: Australia Capital Territory, New South Wales, Northern Territory, Queensland, South Australia, Tasmania, Victoria, and Other.

Hard coded as UDP and Port 5060.

The IPv4 address used to access the DNS server in the Telstra domain.

The SIP Connect Domain or Realm to which the specified IP address will map.

The User ID for use in authentication.

The password to use when authenticating with the User ID.

The re-entered password for confirmation.

The 9-digit pilot number Telstra assigned for use with the SIP Connect trunking service.

IP or FQDN for the host.

The Protocol to use for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled.

The IP PBX port number used for sending and receiving SIP messages.

Disables or enables use of a secondary server.

The FQDN or IP address of the Session Border Controller the Remote Peer service provider.

The IP protocol used for sending and receiving SIP messages between SBC and the Border Element Server. Valid entry UDP or TCP.

The SIP Server Port number used for sending and receiving SIP messages between SBC and the Border Element Server.

Enables or disables the secondary Session Border Controller secondary Remote Peer service provider configured. 

Specify the FQDN or IP address for the service provider's Secondary Border Element Service. Valid entry: IP Address or FQDN. This field is available only when Use Secondary Border Element Server is Enabled.

The Protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled.

The Port Number used for sending and receiving messages between SBC and the Secondary Border Element server. This field is available only when Use Secondary Border Element Server is Enabled.

The IP address or FQDN for the host.

The Protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP. This field is available only when Use Secondary Border Element Server is Enabled.

The IP PBX port number used for sending and receiving SIP messages.

Option to use a secondary server.

The FQDN or IP address of the Session Border Controller service provider.

The IP protocol used for sending and receiving SIP messages between SBC and the Border Element Server. Valid entry UDP or TCP.

The SIP Server Port number used for sending and receiving SIP messages between SBC and the Border Element Server.

Used for setting up transformation rules for the FMC service.

Address of Static Host. Valid options: FQDN[:port] or IP4 [:port] or [IP6]:port

Specifies a user name to use in response to a challenge.

The password for the Authentication ID.

Re-enter the password for the Authentication ID.

Host IP or FQDN.

The Protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP.

The IP PBX port number used for sending and receiving SIP messages.

The FQDN or IP address of the Session Border Controller the Remote Peer service provider.

The IP protocol used for sending and receiving SIP messages between SBC and the Border Element Server. This value is fixed at UDP.

The IP PBX port number used for sending and receiving SIP messages.

Host IP or FQDN.

The Protocol used for communicating with the Secondary Border Element Server. Valid entry: UDP or TCP.

The IP PBX port number used for sending and receiving SIP messages.

For an IP PBX as the user end point, Easy Configuration loads a generic template which follows the “National Numbering Plan” guidelines.

Host IP or FQDN.

The Protocol used for communicating with the IP PBX. Valid entry: UDP or TCP.  

The IP PBX port number used for sending and receiving SIP messages.

Option to add a secondary server. Valid entry: Enabled or Disabled.

Host (FQDN or IP) used for communicating with the Secondary Border Element Server. This field is available only when Use Secondary Border Element Server is Enabled.

Protocol used for communicating with the Secondary Border Element Server. Valid entry: TCP or UDP. This field is available only when Use Secondary Border Element Server is Enabled.

The SIP Server Port number used for sending and receiving SIP messages between SBC and the Secondary SIP Server. Default value: 5062. This field is available only when Use Secondary Border Element Server is Enabled.