Page History

...

...

This section describes configuration required for M-SBC to make basic call

...

1. Validating the Meta Variable Table

2. Creating an IP Interface Group and an IP Interface
3. Creating Static Route
4. Creating D-SBC SigPort
5. Creating DNS Group and DNS Server
6. Creating a NTP Server
7. Creating a Load Balancing Service

...

:

...

1. Select the Media SBC Cluster.Click Configuration tab.

2. Click New Configuration, the . The new configuration window is displayed.

3. Select Version and Master Configurator from the drop-down menu. Enter the Configuration Name.

   Caption
   0 Figure 1 M-SBC Configuring

4. Click Create (the . The configurator clears db and reboots. Rebooting might take 2-4 approximately five minutes).
5. Click Open Editor to launch SBC Configuration Manager.
6. To validate the meta variable table, see Validating the Meta Variable Table.

7. To create an IP interface group and an IP Interface, see Creating an IP Interface Group and an IP Interface.

8. To create static routeStatic Route, see Creating Static Route.
9. To create D-SBC SigPort, see Creating D-SBC SigPort.
10. To create DNS group and DNS server, see Creating DNS Group and DNS Server.
11. To create a an NTP server, see Creating a NTP Server.
12. To create a load balancing Load Balancing service, see Creating a Load Balancing Service.

13. Click Applied Saved Changes and click Close.

14. In the Cluster Management page click Activate Configuration.

    Caption
    0 Figure 1 Activating Configuration

    
     A message Configuration Activated is displayed.

...

To validate the meta variable table, click All > System > Meta Variables. The Meta Variable page displays.

Caption
0 Figure 1 Meta Variables

...

Creating IP Interface Group

1. Log on to into EMS SWe as admin user.
2. In Network Management, click Cluster/VNF Management. The Manage Cluster/VNFs list is displayed.
   
3. Select Media SBC Cluster and navigate to the Configurations tab.
   
4. Select Configuration from the list.

5. Click View Configuration. The SBC Configuration Manager page displays.

   Caption
   0 Figure 1 M-SBC Configuration Manager

   
   

6. Click All tab.
   

7. Select Address Context > IP Interface Group.   The IP Interface Group List page displays.

8. Select default from the Address Context drop-down menu.

9. Click New IP Interface Group. The Create New IP Interface Group section displays.

10. Enter an IP interface group name. For example. Example: MLIG1.

11. Click Save.

    Caption
    0 Figure 1 IP Interface Group 3 IP Interface Group

    
    The Object created successfully message displays. 

12. Repeat step 7  through step 11 to create another interface group. For example, Example: MLIG2. The two interface groups are listed.
    

    Caption
    0 Figure 1 Created IP Interface Group

...

1. On the navigation pane, click Address Context > IP Interface Group > IP Interface. The IP Interface List page displays. 

   1. Select default from the Address Context drop-down menu.
   2. Select an interface group created from the IP Interface Group drop-down menu. For example, MLIG1.
   3. Click +New IP Interface. The Create New IP Interface section displays.
   4. Enter a name for the interface. For example, MLIF1.
   5. Enter IP Meta key for IP Var V4, Prefix Var V4, IP Public Var V4, IP Var V6, IP Prefix Var V6, IP Public Var V6, and IP VLAN Tag Var fields.
   6. Select Mode as In Service.
   7. Select State as Enabled.
   8. Enter the CE Name.
   9. Select pkt0 port from the Port Name drop-down menu.

   10. Click Save.
       

       Caption
       0 Figure 1 IP Interface List 3 IP Interface List
       Image Modified

    
   The Object created successfully message displays.

2. Repeat step 1 to add an interface for MLIG2 interface group for pkt1 port.  The two interfaces are listed:

   Caption
   0 Figure 1 Created IP Interface

   Pagebreak

Anchor
static_route static_route

Creating Static Route

1. Select Configuration > System Provisioning > Static Route. The Static Route List Page is displayed.
2. From the Address Context drop-down menu, select default.
   
3. Click + New Static Route. The Create New Static Route section displays.
   
4. Enter the Destination IP Address (IPv4/IPv6).
   
5. Enter the Prefix value.
   
6. Enter the Next Hop IP Address (IPv4/IPv6).
   
7. Select the IP Interface Group Name from the drop-down menu.
   
8. Select the IP Interface Name from the drop-down menu.
   
9. Enter the Preference Value, default value is 100.
   

10. Click Save.
     

    Caption
    0 Figure 1 Static Route List 3 Static Route List

    
    The Object created successfully message displays.

...

To create a D-SBC SigPort for MLIG2:

1. Select System > Dsbc > Dsbc Sig Port. The Dsbc Sig Port page displays.
2. Select MLIG2 from the IP Interface Group drop-down menu.

3. Click Save.

   Caption
   0 Figure 1 D-SBC SigPort for M-SBC

   
   The Updated Successfully message displays.

...

Anchor
step3 step3

Creating DNS Group and DNS Server

...

Creating DNS Server

1. Select Address Context > DNS Group > Server. The Server page displays. 

2. In Server section, select default from the Address Context drop-down menu.

3. Select the DNS group created from the DNS Group drop-down menu. For example, Example: D-SBC_DNS.
   

4. Click + New Server. The Create New Server section displays.

5. Enter the server name.

6. Select State as Enabled.
   

7. Enter the DNS server IP in the IP Address V4 or V6 field.
   

8. Click Save.
   

   Caption
   0 Figure 1 DNS Server Group

   
   The Object created successfully message displays.
   

...

Anchor
step4 step4

Creating a NTP Server

1. Select System > NTP > Server Admin. The Server Admin page displays.

2. Click + New Server Admin. The Create New Server Admin section displays.
3. Enter server IP address.
4. Select State as Enabled.
5. Select Version as Version4.

6. Click Save.

   Caption
   0 Figure 1 NTP Server Admin

   
   The Object created successfully message displays.
   
   

7. Select System > NTP > Time Zone. The Time Zone page displays.

8. Select the instance from the list. The Edit Selected Time Zone section displays.

9. Select an appropriate time zone from the Zone drop-down menu.

10. Click Save.

    Caption
    0 Figure 1 Configuring Time Zone

    
    The Updated Successfully message displays.

Anchor
step5 step5

Creating a Load Balancing Service

To Configure Load Balancing Service:

1. Select System > Load Balancing Service. The Load Balancing Service page displays.

2. Enter the group name. For example, Example: msbc.lbs.com.

   Note
   The Management fixed IP address should be added as A record in DNS server.

   Caption
   0 Figure 1 Load Balancing Service

   
   The Updated Successfully message displays.

...