Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version 2

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH2UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca7f046c, userName='null'}
AUTH1UserResourceIdentifier{userKey=8a00a0c85bb25531015bc4122a4f0003, userName='null'}
JIRAIDAUTHSBX-86216
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ccbb08c9, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ccbb08c9, userName='null'}

Panel

In this section:

Table of Contents
maxLevel4

 

This section describes 

Spacevars
0product2
 hardware and software requirements and recommendations.

To install and configure 

Spacevars
0product2
, make sure the Virtual Machine (VM) host meets the following recommended hardware, server platform and software requirements.

Warning
titleWarning

The recommended hardware and software settings are intended to ensure optimum 

Spacevars
0product2
stability and performance. If the recommended settings are not used, 
Spacevars
0product2
system may not behave as expected.

SBC SWe for KVM Hypervisor – Server Hardware Requirements

Multiexcerpt
MultiExcerptNameSBC SWe for KVM Hypervisor – Server Hardware Requirements

The following table lists the server hardware requirements.

Caption
0Table
1KVM Hypervisor Server Hardware Requirements

 

Configuration Requirement
Processor

Intel Xeon processors (Nehalem micro-architecture or above) with 6 cores and above (processors should support hyper threading).

Info
titleNote

Ribbon recommends using Westmere (or newer) processors for better SRTP performance. These processors have the AES-NI instruction set for performing cryptographic operations in hardware.

Info
titleNote

The supported CPU Family Number number is 6 and CPU Model Number number must be newer than 26. Refer to the Intel Architecture and Processor Identification document for more information.


 RAMMinimum 24 GB
Hard DiskMinimum 500 GB
Network Interface Cards (NICs)
Minimum 4 NICs.
Info
titleNote

Make sure NIC has NICs have multi-queue support which enhances network performance by allowing RX and TX queues to scale with the number of CPUs on multi-processor systems.

Info
titleNote

The Intel I350, x540, x550, and 82599 Ethernet adapters are supported for configuring as SR-IOV and DirectPath I/O pass-through devices.


Ports

Number of ports allowed:

  • 1 Management port
  • 1 HA port
  • 2 Media ports

Warning
titleWarning

The 

Spacevars
0product2
software runs only on platforms using Intel processors. Platforms using AMD processors are not supported.

BIOS Setting Recommendations

Ribbon recommends the following BIOS settings for optimum performance:

Caption
0Table
1Recommended BIOS Settings for Optimum Performance
BIOS ParameterRecommended
Setting		Details
Intel VT-x (Virtualization Technology)EnabledFor hardware virtualization
Intel Hyper-ThreadingEnabled 
Intel Turbo BoostEnabled 
CPU power managementPower ManagementMaximum Performance 

For example, the BIOS settings are shown below are recommended for HP DL 380p DL380p Gen8 servers. For BIOS settings of other servers, refer to the respective vendor's website.

Caption
0Table
1BIOS Setting Recommendations for HP DL380p Gen8 Server Servers
BIOS ParameterRecommended
Setting		Default Value
HP Power ProfileMaximum PerformanceBalanced Power and Performance
Thermal ConfigurationMaximum CoolingOptimal Cooling
HW PrefetchersDisabledEnabled
Adjacent Sector PrefetcherDisabledEnabled
Processor Power and Utilization MonitoringDisabledEnabled
Memory Pre-Failure NotificationDisabledEnabled
Memory Refresh Rate1x Refresh2x Refresh

Pagebreak

Multiexcerpt
MultiExcerptNameSBC SWe for KVM Hypervisor – Software Requirements

SBC SWe for KVM Hypervisor – Software Requirements

Following The following are KVM hypervisor and SBC SWe software requirements for a KVM hypervisor environment:

Caption
0Table
1KVM Requirements
SoftwareVersionTested or Qualified Version
KVM Module 3.10.0 or above3.10.0
QEMU Emulator  1.5.31.5.3
libvirtd (libvirt)1.1.11.1.1
virt-manager0.10.00.10.0

Downloading the SBC SWe Software Package

For more information, see Downloading the SBC SWe Software Package.

Info
titleNote

Processors and VM configuration (CPUs, RAMsRAM, Virtual Hard Disk, NICs, and bridge SettingsBridge settings) must be identical for an SBC SWe HA pair.

Info
titleNote

BIOS settings and recommendations must not be changed once it is they are applied on the server.

KVM Configuration Recommendations 

Caption
0Table
1KVM Configuration Recommendations


 vCPU

Minimum 4 vCPUs required. Any number of vCPUs may be configured depending upon the call capacity requirements, but the number should be even (4, 6, 8, etc.) to avoid impacting performance.  

 vRAM

Reserve the memory based on call capacity and configuration requirements. Refer to benchmarking data for supported call capacities with different configuration limits.

Virtual Hard Disk 

Set Hard Disk (virtual) size as 100 GB or more (based on requirements of retaining CDRs, logs, etc. for number of days).

 

Note: Hard disk size cannot be changed after the SBC SWe software is installed.

vNICs

Set number of virtual NICs as 4 (1-MGMT, 1-HA, 1-PKT0 and 1-PKT1).

  • Use only Virt-IO driver.
  • Associate each vNIC to separate bridges.



Info
titleNote
  • Processors, KVM hypervisor version and VM configuration (vCPUs, vRAMsvRAM, Virtual Hard Disk, vNICs, and vSwitch Settings) must be identical for an SBC SWe HA pair.
  • BIOS and KVM hypervisor settings and recommendations must not be changed once it is they are applied on the server.

 

Pagebreak